Reviews
For the do-it-yourself maintenance group, this is a good one to have.
Restore of immovable ESTRELLA.
Final touches, Tappet adjustments.
Oil leak is gone but Engine noise is annoying.
However, I need to prepare Thickness Gauge for Tappet adjustment, so I bought this one.
[What happens if I don't make the Tappet adjustment?
Of course, if the tappet noise is too loud, it will bother you, but if you leave it as it is, the wider the gap, the stronger the impact of the blow, and the tappet clearance will widen more and more, which will cause the starting performance to deteriorate and the motorcycle to gradually go out of tune, so adjustments are necessary. 。
What is a mismatch in Tappet clearance?
When the Valve clearance (Tappet) gap becomes Large, a hammering sound begins to be heard. 。 Sound is emitted when Engine is cold, but disappears when warmed up. 。 In such a case, the gap is large, but as it warms up, the gold expands and the gap becomes small, and the sound disappears.
Symptoms
When I stopped at a traffic light, the car stalled while holding the clutch and dropping the GEAR.
In accordance with the Fat Engine Rotation "Tinkle, tinkle, tinkle." and strange noise.
Procedure 〜For ~ESTRELLA
(1) Unload the Tank from the vehicle body.
↓
(2) Cook must be Off 。 By turning it Off, you can lower the hose without wasting Gasoline dripping out (some Gasoline in the hose will come out immediately after the hose is removed).
↓
(3) ESTRELLA can be adjusted to the upper dead center by removing the Cover and turning this Screw. 。 Top dead center is simply the state where the Piston is at the top.
When adjusting the tappet, the position of the piston must be adjusted to the upper dead center. 。
↓
(4) Remove the Plug so that no compression is applied.
I have to move it with no Engine on it.
↓
5) Front Tappet Cover. 。 It can be adjusted by removing here.
↓
(6) Loosen the lock nut attached to the head first, and when the center screw can be turned, it is OK. 。
At this point, it is normal to move the Tappet by hand and hear a chica-chica sound. 。 If it does not sound kachica-chi, either the upper dead center is not correct or the adjustment is gapped considerably.
↓
(7) Insert the Thickness Gauge into the gap and align it. 。 Strictly speaking, this is the process of adjusting the gap between the Valve and the Arm that is pushing the Valve to the proper value.
↓
Clearance on the exhaust side is 0.17 to 0.22mm 。 If the Gauge is pinched by inserting 0.20mm of Thickness Gauge and closing the Screw at the Center, the Gauge will be pinched, and if the Gauge is moved in that state and it feels a little stuck, it is OK. 。
↓
Clearance on the intake side is 0.10 to 0.15mm 。 The intake side may be a little more difficult to do because it is more intricate in location.
↓
(10) To be sure, make one more rotation of the screw with the upper dead center aligned, and then align it again.
[After adjustment
When I drove it, it no longer stalled and blew up better!
I think a single cylinder can be done by an amateur.
View detail
To adjust valve clearance
The feel is perfect.
After use, moisten it with engine oil and place it in a small bag to prevent rusting.
View detail
This is a good product that is inexpensive and easy to find.
[How is it used?
To the Deer Baron. "The old Motorcycles are getting pretty crazy with Valve Clearance. I was ad-vise and bought it in a hurry.
It used to be a regular item at the nearby Home center car parts corner...
Was the one you received as per Image?
Simple & Compact, as per Image.
How was your experience with it?
It's nothing to write about, it's just a normal chic Snes Gauge, because the purpose of using this tool is clear. "It's so easy to use." And "It's so hard to use. I don't think you can make a product that says
[Points to note]
If you handle it roughly, the Plate will be bent and it will be difficult to use the same Plate next time.
Well, if it gets bent and hard to use, you can just buy a new one...
How did it compare to other products?
Since the purpose of use is clear and limited, there is little difference from other companies' products.
Other items that would be helpful
[ITEMS TO BUY TOGETHER
I think that the person who needs this tool is already able to do some maintenance, and I don't think that it is necessary to buy it.
[Opinions and requests to Manufacturer
I hope you will continue to sell it at an affordable price.
View detail
I think it's good
I haven't used it yet, but it seems to work fine. View detail
Engine for Clearance
This is my first time buying a Thickness Gauge
0.I was looking for 08?s and didn't find any in the neighborhood
I thought they were arranged in order, but there's a thin Size in the middle, and a thicker Size in between them There is a
Perhaps a toolbox or something to prevent it from getting bent out of shape? Various patterns are available, so you can't go wrong with this product
View detail
Value for money
Very satisfied with this thickness gauge,good quality yet reasonable price.I am using this to adjust my Yamaha sr400 valve clearance,everything went smoothly during the whole process and my bike become less noisy and ride smoother.A must have in a toolbox if u enjoying service motorcycle at home.Thank you WeBike View detail
Required enough for SR 400's Tappet adjustment
I bought it for adjusting the Tappet of SR 400.
It is necessary and sufficient as Gauge, there is also a sense of security that it is domestic production.
It can also be used as a consumable item because it is cheap ◎
View detail
For Valve clearance measurement ...
In the item description, "measurement range 0. 04mm 0. 05mm 0. 06mm 0. 07mm 0. 08mm 0. 1mm 0. 30mm Quantity : 1 Set of 7pcs. There is, but 0. 15 mm and 0. Since there are 2 pieces of 20 mm, Quantity : 1 Set of 9pcs. is. This item, Length is 100 mm and somewhat longer and easy to use.
In the opened state, the root is hard and the Thickness Gauge is difficult to put in and out. First of all, applying Oil or a rust preventive penetrating agent etc. to this root part makes it possible to rotate the thrusul and the Thickness Gauge, making it easier to use. 【Made in Japan】 I feel reliable!
View detail
It is a lifetime if you use it with Motorcycle
【What made you decide the purchase?】 It was cheap in JAPAN.
【How was it actually used?】 It can be used without waste.
【Was it difficult to install? (Hard parts case)】 nothing special.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Be careful with rust. Wiping off the oil lightly when measuring. If you can not respond to Size please use several sheets in combination.
[Is there anything I was disappointed about?] None
【Hope for Manufacturer - Please tell me if there are any improvement points】 None
【Have you compared items?】 Asian cheap Gauge
[Others]
It was the only condition of Kowa if it was a condition that it was exactly good at domestic production and Compact.
It is made with very high precision, and it fits snugly when you folding it.
Although I have bought Asia's cheap Synness with another business, although I can measure it
It was hard to put in and out and it was hard to use.
I might think that the performance of loading and unloading is not related to the measurement, but wait a moment!
Since there are many times to use multiple sheets in a stack, the performance of taking out and taking out is related to Large as usability convenience!
This is a bad thing to do Sickness is getting irritated.
The durability is also quite high "Do not rust" "Do not press hard" "Do not fold" The three iron rules of
I think that it is lifelong if you protect it. Indeed, I myself used for 23 years without any problem. so much
Although it is not used frequently.
It is a pleasure to buy such a high precision measuring instrument at around 500 yen.
Ultra is recommended.
View detail
It is satisfied with a Cost performance. Since it did not use usually [ ], the cheap thing was looked for. If it is likely to rust if an Oil is not applied unlike quality articles, but a Cost performance is considered, I will think that it was goo
It is satisfied with a Cost performance.
Since it did not use usually [
], the cheap thing was looked for.
If it is likely to rust if an Oil is not applied unlike
quality articles, but a Cost performance is considered, I will think that it was good now.
View detail
If there is a size like this, first of all, it will not be troubled. They are necessaries at Tappet adjustment.
If there is a size like this, first of all, it will not be troubled.
They are necessaries at
Tappet adjustment.
View detail
It is used for Tappet adjustment of a MONKEY. Since the Schickness gauge is businesslike with consumable goods, the required Size has gathered and I think that what has a cheap price is the best. I think in that respect that the Gaug
It is used for Tappet adjustment of a MONKEY.
Since the
Schickness gauge is businesslike with consumable goods, the required Size has gathered and I think that what has a cheap price is the best.
I think in that respect that the Gauge of this KOWA maintains the Balance very much.
View detail
It purchased to disassembly in the MONKEY on the waist. Even if also making is solid and it does not use the high thing of the other company, I think that this product is enough.
It purchased to disassembly in the MONKEY on the waist.
Even if also making
is solid and it does not use the high thing of the other company, I think that this product is enough.
View detail
It purchased for Tappet adjustment of a SEROW. Although it was the first work, it was able to finish satisfactorily especially. Since it was setting out with the comparatively cheap price, it considered it is OK ? in quality, but it also seemed
It purchased for Tappet adjustment of a SEROW.
Although it was the first work, it was able to finish satisfactorily especially.
Since it was setting out with the comparatively cheap
price, it considered it is OK ? in quality, but it also seemed to be groundless apprehensions.
Because it is cheap, even if it breaks, it can be said that what is necessary is just to replace.
Although the tool of
Kowa energy machine uses the Tire lever and the Glasses wrench for others, the touch referred to as simple and sturdy may be sufficient as it.
View detail
It is very much satisfied with the High cost performance. Although it does not always use, it will be troubled if there is nothing.
It is very much satisfied with the High cost performance.
Although it does not always use, it will be troubled if there is nothing.
View detail
It purchases in order to adjust a Valve clearance. -- it is cheap -- -- it is easy-to-use and is also putting accuracy in order! It is one [ highest ] without the complaint.
It purchases in order to adjust a Valve clearance.
-- it is cheap --
-- it is easy-to-use and is also putting
accuracy in order! It is one [ highest ] without the
complaint.
View detail
[Webike Monitor] To Valve-clearance adjustment, the Size has also gathered enough and is cheap positively!!
[Webike Monitor] To
Valve-clearance adjustment, the Size has also gathered enough and is cheap positively!!
View detail
It purchased for the tappet adjustment of NSF100. Although purchased from the low price of the price, anything does not have fault, either and I think that they are good goods. In the direction which asks for cost performance, it is a recommend!
It purchased for the tappet adjustment of NSF100.
Although purchased from the low price of the price, anything does not have fault, either and I think that they are good goods.
In the direction which asks for cost performance, it is a recommend!
View detail
It purchases in order to challenge the tappet adjustment of KSR110. It is as cheap as it says, It says by such a cheap tool. Are the die length, form, and user-friendliness of a gauge as perfect as uncertain (smile) considering the tool used by th
It purchases in order to challenge the tappet adjustment of KSR110.
It is as cheap as it says, It says by such a cheap tool.
Are the die length, form, and user-friendliness of a gauge as perfect as uncertain (smile) considering the tool used by the work which determines the engine engine performance at it?
Although there are also goods with many kinds of thickness of a gauge inexcessively, to put it bluntly, it is useless.
If there is even a kind of required gauge, it is sufficient for Koto.
It is made required and enough, if that meaning is also this product.
Let's take out * five pieces without a complaint!
View detail
The die length of the feature of this schickness gauge is a long time moderately. It can work like a photograph also at the time of adjustment of valve clearance, being able to have a margin. Although the shorter gauge was used before, troubles we
The die length of the feature of this schickness gauge is a long time moderately.
It can work like a photograph also at the time of adjustment of valve clearance, being able to have a margin.
Although the shorter gauge was used before, troubles were suffered without the ability to perform flexible bending like a photograph.
I think that they are goods excellent in cost performance.
View detail