Reviews
Fits: HONDA GORILLA (GORILLA), HONDA GORILLA (GORILLA), HONDA GORILLA (GORILLA), HONDA GORILLA (GORILLA), HONDA GORILLA (GORILLA), HONDA GORILLA (GORILLA), HONDA Monkey (MONKEY), HONDA Monkey (MONKEY), HONDA Monkey (MONKEY), HONDA Monkey (MONKEY), HONDA Monkey (MONKEY), HONDA Monkey (MONKEY), HONDA Monkey (MONKEY), HONDA Monkey (MONKEY), HONDA Monkey (MONKEY)
NTB Flasher relay for 2 wheels 6V
This is a smaller type than the OEM Product, but the performance is almost the same. I removed the battery case, put the bracket over it, and installed the relay when I installed the regulator, so it fits nicely inside the Left SideSide cover. View detail
For terminals of 4.0sq cord for charge current
I bought a battered 900SS (900SL) and am Restore.
The harnesses are also in bad shape, so we cut and re-created the damaged parts of each section.
The very thick wire for the Starter motor and the carburetorTire wire connecting the Engine and Chassis are also deteriorating over time and are crumbling and falling apart.
The internal core wire was also corroded by moisture that had entered the wire and was spewing GreenBlue, so it was re-created.
After the terminals are crimped with Electric Works Pliers, solder is applied to the terminals for secure wiring, and these terminals are protected with Shrinkable Tubes to prevent shorts.
The tube is coated with an adhesive that melts when heated and shrinks to make it Completely Waterproof, preventing moisture from entering the cord through the terminals.
It also serves as a Cover for the terminals, so using different colors of this Shrinkable Tube (Red and Black) helps to prevent accidental wiring.
It is especially effective when used in the terminal section that conects directly to the Battery terminal.
Φ9.5 is quite thick for Motorcycle wiring, so there are not many uses for it, but it is ideal for terminal protection for Starter and Earth.
Although it is possible to purchase a similar product at a wiring store at a much lower price, considering the time and effort required to go there and the use of multiple mail order sites, I think it is most cost-effective for ordinary people to buy a DAYTONA product at Webike, even if it is a little more expensive.
View detail
Trust.
It claims to be weather resistant, so trust it anyway.
I have always been an Emon believer.
… I don't think it's any different than the others, … (laughs)
2sq for Grounding Wire.
View detail
for Replacement
Relay on headlight relay kit suddenly broke
Purchased two Relay replacements because it's not a Wiring problem.
The product is an ordinary product with no negatives or positives.
I replaced the Relay so I can use it safely for the time being.
View detail
Effective
I purchased this for a power supply for a Grip heater that is attached by wrapping it around.
In the summer, I remove the Grip heater, so I use this Connector for One-touch power supply.
The waterproof specification is safe and secure.
The terminals are small and can be damaged if you are not careful when crimping through wiring.
View detail
Fits: KAWASAKI GPz1100, KAWASAKI Z1000J, KAWASAKI Z1000R, KAWASAKI Z1100GP, その他 , KAWASAKI Z750-D1 (KZ750D), KAWASAKI Z1100 R (US), KAWASAKI Z1000 MkII, KAWASAKI Z1000 A1-A2(US), KAWASAKI Z1-R, KAWASAKI Z750-D1 (KZ750D), KAWASAKI Z1100 R (US), KAWASAKI Z1000 MkII, KAWASAKI Z1000 A1-A2(US), KAWASAKI Z1-R
Essentials for old cars
It was introduced as a countermeasure for KATANA's vehicle inspection. It has already been installed in NINJA and GOOSE, which I also own. View detail
for storing wires or cables as needed It is chrome color, the material is springy, easy to use. View detail
About the same thickness as Car's Audio systemWiring
0.5sq, as the Title suggests, is ideal when thicker Wiring is not required!
I'm surprised (and grateful) that Webike also handles it.
View detail
Bigli handled by Web!ke
0.The thickness is 5sq, which is often used for car audio system decks and the like. View detail
Essential for DIY of electrical components
It's a must for DIY electrical components.
RedBlackDouble is easier to compile during Wiring!
These are the parts you want to keep in your toolbox along with Bullet Terminal and Electric Works Pliers.
View detail
Tidies the wire system on your handlebar
Installation was easy and it can be customed to the desired length. Looks wise, it creates a singular and more neater at the steering area. Material is also sturdy and it stays at the position where you set it. View detail
Cosmetic Items for DIY
[How is it used?
I purchased DAYTONA's Power Unit D-UNIT+ for my XJR400R.
In this process, the stag beetle terminals were modified to Round Type Terminals, and Heat Shrink Tubes were used for waterproofing and terminal protection.
How was your experience with it?
The product was easy to use.
I didn't have a heat gun, so I used a Chuckerman to apply heat, but the shrinkage was firm.
The quantity is so large that I don't think we will run out of it in the foreseeable future.
How did it compare to other products?
Some products are sold as a single item in 6cm increments, but this product is easy to use because you can cut it to any length you like. Also, the package itself plays the role of reel, so it is easy to store.
[Points to note]
It does not have a clear waterproof effect, so care should be taken where it is used.
Also, the shrinkage rate is not that high, so choose the Size according to the actual Wiring you will use.
One concern is that the package is larger than expected, making it somewhat bulky when stored.
View detail
For SUPER SHERPA.
SUPER SHERPA does not have a hazard switch, so I was afraid when I had to stop for traffic or construction at night on the highway, but now that the hazard switch is on, I can tour with peace of mind. I am really glad I bought it. It's like a good luck charm. As expected, there were some positioning problems with Wiring and Relay, but I managed to get it to fit nicely. It's a ba direct, so you have to be careful not to forget to turn it off or play tricks with it. View detail
usual
I think it is a standard Wiring.
I can't compare whether it is good or bad, as I have only used this one, but I am fully satisfied with it.
I will continue to use it if I need anything in the future.
View detail
It's good.
I bought it because I just needed a code. It is Emon, a trustworthy company. View detail
Handy Ring Terminal Lead to Ground Universal Accessories to the Grom
About quality and texture: I am happy with the quality of ring terminal lead from SP Takegawa made from a ring terminal, male bullet connector and small section of wire About the feeling of use: Makes connecting a ground to universal accessories like my temperature guage that is not Grom specific a breeze and there is no premanently cut wires if the accessory is removed in the future. Products to buy together: An electro tap would also be desirable to purchase along side the ring terminal lead so that a power can be provided to the accessory via the motorcycles wiring harness. Difficulty of installation: The process to install takes about 5 minutes, the accessory will need a female bullet connector fitted and simply connect the bullet connectors and bolt the ring terminal down onto a section of the Grom's frame that is free from paint for a good connection. Not difficult to do. Cost performance and comparison with other products: Good costing as you are getting two leads complete with connectors to save you the time preparing these yourself as compared to purchasing all the items individually which will be cheaper if you need numerous leads. About shipping and packaging: The faster shipping options are too expensive for myself so I just have to wait for my part to arrive via sea freight. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: This is a relatively short lead and if you are needing different lengths search grounding cable for many more options. View detail
Easy to use
[How is it used?
The Heat Shrink Tube I had on hand went somewhere, so I bought one.
I chose this product because it is a sizeφ3.2mm, which is often used in Wiring, has a length of 3m, and is relatively inexpensive.
How was your experience with it?
The required length can be taken out and used immediately.
Heat gun (or writer) The work can be done easily by anyone who has
Shrinkage is not a problem, and Wiring looks great, so I recommend it.
[Points to note]
What is ReelPackage? I was wondering, but you can use it without taking it out of Package.
I opened the Package once without understanding, but please be careful if you are going to use it in the future.
How did it compare to other products?
I've been using it for a while now. (probably Emon's). There was no particular difference between the two.
It is long enough for amateur DIYers, so it is nice to not have to worry about buying more.
【Review】
It is easy to use, long enough and cost-effective.
If you are processing Wiring yourself, you should have one to make your Wiring look better.
View detail
It uses, when changing the present blinker a hazard and with a position.
It uses, when changing the present blinker a hazard and with a position. View detail
When touring with friends, turn on Hazard and stop
It is a good product with detailed instructions and easy installation for those who are somewhat familiar with Wiring. View detail
Hazard kit
Purchased to install Hazard on 400KATANA.
There is an instruction manual and it was easily completed.
Now I am looking forward to seeing how long it will last.
View detail