Reviews
Chain cleaning essentials
[How is it used?
Used to clean Chain every 500 km.
Chain cleaner is sprayed on and then shakily scrubbed.
Was the one you received as per Image?
As per image.
If they cost more than 1,000 yen each, a little more BALIetc. surface treatment would be nice, but it does not affect the performance.
How was your experience with it?
The size is just right for MotorcycleChain, and the back and underside of the chain can be easily cleaned.
[Points to note]
Spraying and scrubbing with the Cleaner will clean the Plate surface of the Chain and feel good, but it is important to use a Large amount of force to avoid damaging the Seal Ring more than necessary.
How did it compare to other products?
I think DAYTONA and others are almost the same in shape and performance, but the Brush part seems to be interchangeable.
Other items that would be helpful
Items to buy together
・Maintenance Stand
・Chain cleaner
・Chain lube
・Dustcloth
Rubber gloves etc.
I think Chain maintenance can be done anyway if there is a
View detail
moment
It was removed in an instant with a special tool.
It is oiled to prevent rust, and comes with a small amount of grease (pack) to prevent biting. A small amount (pack) of grease is also included.
View detail
I can't think of anything else.
This Cable Louver and Bell Hammer will make you happy!
Lubrication of the wire cable is completed in one stroke.
Clutchetc. operation system, even if you don't ride Off, the lighter the better, of course.
It is pricey, but well worth the purchase.
View detail
Prices are high because there are no competing products.
I bought it because I can't get UNIT's Shocker Punch, but it is overpriced.
The function is good to be able to adjust Motorcycle by hitting it through the gap without ROSE.
I used it on my CRF250L. UNIT's products are priced right.
View detail
Use it and you'll be convinced!
I gave high marks to Costa, but at first I thought it was expensive!
But if you use it, you will be convinced and impressed, that's all!
No more frustration with Injector!
I definitely want you to use it!
View detail
It's easier to work with, but...
Found from WeBig's imprint.
I wanted to see it used myself and bought it lol.
I used it right away.
Certainly, the grease leaks less than the one I used to use. However, the grease spray inlet is too small to fit the grease spray that I have, and it leaked from there.
I wonder if it would be easier to use if I could devise a little more.
View detail
The Wire lube injector lives up to its reputation.
[How is it used?
Used for refueling Wire
Was the one you received as per Image?
Yes
How was your experience with it?
The lubricant reached the tip of Wire better than I had imagined.
[Points to note]
Note the direction of the wire's leak-proof rubber.
How did it compare to other products?
The unit price is high! But after using it, I am convinced. I don't think I will ever use Injector again!
Other items that would be helpful
Opinions and requests to Manufacturer I would like to see the rubber parts issued as Repair Parts, as their lifespan is unknown.
View detail
Best, but not omnipotent.
I became interested in it through a feature article on webike and bought it.
It is significantly better than the common Aluminum Injector, but not completely problem-free.
First of all, it takes time to put it on. The Packing is put through the Cable and the Body is tightened, but the amount of tightening is large and must be turned many times.
When the body is full, the remaining oil leaks out from the slide portion when the body is removed, so curing and dustcloth preparation are essential.
Naturally, it cannot be used with the Cable with Throttle's Guide (the same applies to the conventional product).
I am concerned about the durability of the spiral Cut Packing as it is a special shape and not sold individually.
However, there is nothing better than this in terms of oil feed capacity, and since pressure can be applied at the slide, even hardened old oil can be pushed out at once.
View detail
It can also be used for car washing.
One thing that always accompanies an off-road motorcycle is, after all, washing the car. It would be nice if we could use the car wash machine at Course to wash the car immediately after riding, but that is not always possible.
It would be nice if you could wash the car right away, but if you leave the car for a while, the mud will harden and make the car wash even more Large strange. Therefore, it is recommended to wash the car at the timing when the mud is still dry after driving, so that the mud can be easily removed.
It can also be used with the Moto Spade in one hand while scraping mud out of the car wash. The Brush part is especially easy to use when washing the car.
It is a well thought-out form and easy to use, as only the Brand "Motion pro" can do.
The only drawback is that it is a bit expensive.
I try to carry it with me by shoving it in my car's Off supplies box.
View detail
Thank God!
I used to use a Wire injector of the type often sold at supply stores, but I couldn't get it to refuel properly, so I bought this one.
I was a little bit worried about the wire injector, but it turned out to be the right decision.
I used Bell Hammer for the Oil and was pleased with how well it penetrated from entrance to exit.
View detail
Special Tool is now a discontinued MODEL.
This tool is used for hammering in Stem bearing.
Exclusive Design makes it easy. (and beautifully) Bearing race can be installed.
If the Manufacturer tool is already discontinued, you can have it.
View detail
You can throw away all the other W's except this one.
[How is it used?
The number of large motor cycles with cable-type clutches has increased to two, and although we had a conventional wire injector, it was no longer useful and was left unattended.
I was thinking it was time to clean and lubricate Cable and then I saw the Webike introduction article.
I thought, "This is it! I thought, "This is it! It took more than a month for delivery, but I finally received it the other day and tried to use it right away.
Was the one you received as per Image?
It was bigger than I expected. w The length is about as long as a box of Cigarette.
It seems to be a California-based manufacturer, and although it was manufactured in China, I think the quality is not bad.
How was your experience with it?
Compared to the conventional type of wire injector, Quantity:It takes time and effort to Set.
The procedure is
Turn the body and separate it into two pieces→Pass the Cable through→Attach the black rubber part by wrapping it around the Cable→Screw the separated Body→Lubricate it
I had to shave the tip of the tube to make it thinner, but it is better than too thick because it can cause leakage.
Quantity:Set is time-consuming, but it is possible to properly set theQuantity:If you set the wire injector, it will not leak all over the place and not enter the Cable at all, as is the case with conventional wire injectors.
Every drop of the blow is injected into the Cable and blown out from the other side, which is Large strange and pleasant.
Stress-free.
[Points to note]
Quantity of Rubber parts inside:If the set-up is not properly done, it will leak. Since the structure is sealed at three points including the O-ring and other rubber parts, it will leak if it hardens over time.
There is some concern about durability in that area.
How did it compare to other products?
It is incomparable to conventional wire injectors in terms of leak-free and reliable lubrication.
Exactly Throw away everything but this." W
It is expensive, so it depends on how long you can use it, but I think you will be happier buying this rather than getting frustrated with Gold for a tool you can't use.
View detail
Necessary for disassembling and assembling Engine.
The price is a bit expensive, but it is necessary for disassembling and assembling off-road engines for competition use. The Blue Anodized is like Motion pro, and the Parenthesis is nice. View detail
Better than ever!
[How is it used?
I used it to make the clutch a little lighter and to prevent the wire from rusting, since the clutch yawer was replaced.
Was the one you received as per Image?
I'm using it for the first time. YouTube." I tried it after watching the video at
How was your experience with it?
Installation was easy and lubrication came out the other side of the Wire with no leaks.
[Points to note]
Be careful of the direction of the rubber packing that fits into the wire, and press the top part at the end to drain out any remaining lubricant inside.
It is
How did it compare to other products?
The Injector I used to use leaked lubricant from the entrance even when the screw was tightened, and only about half of the lubricant flowed out.
It was like they were not coming.
I don't think I will ever use the old Injector again.
View detail
Overhaul of Master Cylinder
It is very useful when doing overhaul of the brake master cylinder.
It is a Copy product of HondaOEM tool, but it is durable and easy to use.
I use it a lot for my work, so the price is not expensive and well worth it.
View detail
It's the only way
I had another wire injector, but when I used it, the oil leaked out and it was no good at all. This one, however, did not leak any oil and did exactly what it was supposed to do. The price may be high, but this is the only way to go. View detail
Fits: HONDA XR650 L, HONDA XR650 L, HONDA XR250 R, HONDA XR250 R, HONDA VT750 CD2, HONDA VT750 CD, HONDA VT750 C, HONDA VT750 C, HONDA VT750 C, HONDA VT600 CD, HONDA VT600 CD, HONDA VT600 C, HONDA VT600 C, HONDA FT500(82-83), HONDA GB500, HONDA NT650, HONDA NX650, HONDA RVT1000R, HONDA TL250(75-76), HONDA VF1000F(84)
VFR750F Flywheel removal!
Must-have item to remove the Flywheel due to StatorCoil failure! The puller itself looks like just a thick bolt, but the screw threads and texture are solid! It's a good time to be able to find tools like this quickly, as the number of old motorcycles increases and special tools are suddenly needed. View detail
The best, but maybe not all-purpose.
Rumored Cable injector guy.
It is actually well thought out and much easier to use than the traditional Injector.
However, the size of the Cable's length adjustment nut is too large because it is made to enhance sealing. (about M8) In some cases, such as in the case of a Cable, the Injector may not be able to bite into the Cable's sheathing thanks to that section.
Also, sticking Wire× I could not penetrate the Grease with Wire grease with high viscosity.
Anyway, it seemed to work well with low viscosity GreaseorOil, and it is a much better tool than the existing Injector.
View detail
Seal mounting is easier.
I am concerned about the durability of plastic, so I prefer DRC's Stainless Steel tool, but it has been out of stock for a long time. I would prefer to use DRC's Stainless Steel gloves, but they have been out of stock for a long time. It is inexpensive, so I can just give up and buy a new one if it breaks. View detail
As a primer to make car washing easier.
I used to put my off-road motorcycle on the transporter after a race and ride it home without cleaning the dirt off the body. However, by the time I arrived home, the dirt had hardened into a stubborn stain, making it difficult to wash the bike each time... (And mud falls in the Transporter...) If that's the case, why don't you just clean up the dirt there? So why don't we just clean the dirt off the car locally? I bought this to clean the dirt that gets into the back of the Fender, the footpeg, and the tight spots on the body at the site! I will use it in the future when I have a chance. View detail