Reviews
To prevent Axle Nut from loosening on older cars.
I used this as a split pin to prevent the Axle Nut from loosening, which is common on older cars. I always do this because it is easier to purchase than to look up the OEM Product No. and order one at a time.
For Motorcycle, the 3 sizes included in this kit should be sufficient for Large.
View detail
Ideal for Driven Sprocket Nut
I purchased the 12mm to replace the Driven Sprocket on my KLX125.
As a result, I am satisfied with Large!
If you have ever replaced the Driven Sprocket on a KLX125, you will know that when holding the Nut on the Driven Sprocket, the Neck is where the Rim/Tire is located.
LongGlasses/Spanners interfere with the Rim/Tire, so the tool must be hung on the Slant, while ShortGlasses and normal length Spanners are too short to hang the Torque.
I had been using Long spanner, but I thought it was not a good idea, so I bought this one.
Good point #1.:Moderate Offset
The handle and Glasses section are moderately offset so that the Nut can be held without interfering with the Rim/Tire.
Good point #2.:thin
Related to (1), it is made thin and does not interfere with the Rim/Tire.
Good point #3.:No counterbore in the Glasses area.
They have eliminated the counterbore, so the Nut can be held firmly even at this thinness.
Good point #4.:Simply cool
I like UNIT tools and have several of them, they are cool.
The ruggedness of the black color, the UNIT logo shining on it, and the gentleness of the handle covered with rubber.
It's a hobby of mine, but I just can't get enough of this coolness.
It is not so frequently used for personal use, but it is very useful when replacing a Driven Sprocket! It is a very useful tool when you need to replace a Driven Sprocket.
When in doubt, buy. Please try it out at Su Chest in
View detail
Niche tool but Large active!
True to its name, the Brake Pads Opener is a great tool for widening the gap between Brake Pads.
In our house, this one has been used from One Side 1 pot of Hara 2Scooter to 6 pots of Large type On road facing each other.
How often do you use it that often? You might think,
It is used unexpectedly frequently for assembly after cleaning the brake caliper or reinstallation of the wheel after removing it for tire replacement, etc.
In my case, I also have an off-road motorcycle, which I use for both touring and racing, and I prepare separate wheels for touring and for racing and set up tires on each wheel, and then change each wheel depending on the application.
I change the wheels for RaceWheel about 3 times a year and change them for TouringWheel when the race is over. Therefore, the Opener is a big help to me.
It's not bulky, and it's a really useful tool to have, so it's a recommendation!
View detail
Expect durability
I bought this because my long-time Socket was getting a little licky. 900SS Cowl removal is 4mm, so I use it a lot. I tried it out right away and the new one chews very well indeed, no more worries about Bolt licking it. View detail
If you're not good at it, you'll break it. You're not good at it.
Hit it straight, don't rush, and take your time.
I didn't expect it to break... I wish I had a couple of spares.
I don't think we are in a hurry.
The work doesn't stop and it doesn't take time to make arrangements.
Do not make the mistake of matching the Chain size!
View detail
This eliminates the need to search for tools.
Rose and kept it in my toolbox. Separate from the tools for my main job,
It is stored in the Motorcycle garage. I use it by hooking it to the Neodymium Hook as shown in the picture, considering that it is easy to understand and within easy reach.
View detail
Drumstickn, Drumstickn!
I often make my own parts for ZEPHYR400 and CUB90. I often use Aluminum plate as material.
For the cutout, we used different tools depending on the thickness:Gold scissors tend to bend the object while cutting, and an iron saw tends to blur the cutting line. It took a lot of time and effort to make the final correction and polish it to make it less noticeable.
I had never seen SK-11's Hand nibbler tool in person, so I did not have an Image to use it. I had never seen a hand nibbler before, so I did not have an image of using it. I purchased it and found it easy to use, and I enjoyed cutting aluminum and steel plates. It is not like cutting with a normal scissors, but with a drumstick, a drumstick, a drumstick.
The blade is a sturdy Square Type with a thickness of approximately 6mm. The blade is clamped between the blade and the board, and the blade moves down and cuts off the board in one grip. The grip force varies depending on the material and thickness to be cut; even aluminum plates are quite tiring. It is easier to cut by gripping the blade or placing the lower side of the fixed grip against the flat surface of the worktable and pushing the working grip in with your arm strength.
I had a person with a weak grip use it; he could not cut a 1mm Aluminum board with one grip. I think it has something to do with the strength. I'm afraid that if I force myself to grip it too tight, I'll hurt my fingernails." I was told. I could use a leather hand, but it is dangerous and difficult to slip.
Because of the thickness of the blade, the cut will drop about 6mm worth of cuttings. In the case of an iron saw, it will be about 2mm worth of iron dust. It is better to use different tools considering the labor and the processing time after cutting.
The blade bite was good when new, but the blade is starting to round off a bit. It would be nice to replace or polish the blade, but since it is inexpensive, it may be a good idea to replace it.
If you want to make longer cuts, you can choose an electric saw. However, for small workpieces, SK-11's Hand nibbler is sufficient.
View detail
Convenient to carry
Compact and very good for motorcycle loading View detail
Expensive but good product.
I bought it for a place where I really want to fix Wiring.
It's Titanium, so it's expensive, but I'm satisfied.
View detail
The knock pin are a part that do tend to sustain damage and is advisable to replace when this the case
About quality and texture - The pair of knock pins from K-Pit are made from steel and raw surface finish, the quality from the overall fit and finish is perfect. About the feeling of use - The knock pin is a part that do tend to sustain damage and is advisable to replace when this the case. This will ensure easier installation and removal of parts like the cylinder head, cylinder and crankcase halves when it comes time to overhauling the engine, as this is where they are used on the Honda Grom. Products to buy together - Key products to purchase when overhauling the engine would be gaskets and O-rings, all which are available from K-Pit here on Webike for the Honda Grom. Difficulty of installation - The installation of the knock pin is an simple task that took 0.1 of an hour to complete. Common sense and the use of your hands is all that is required to clean the mating surface and press the knock pin into place. Cost performance and comparison with other products - I find the cost of all the products K-Pit sell to great value when compared to what most other companies sell their products for and the knock pin is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the knock pin, I chose EMS for an earlier arrive date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - Webike Japan is the first place I look to for all my motorcycle needs. From service parts to performance products and even motorcycle gear and apparel, Webike always seem to satisfy my needs in regards to availability and pricing. View detail
no problem
There were no problems, and the product could be used normally. View detail
Only special tools can do this.
In order to revive the immobilized YamahaRZ350, I set out to overhaul it, but the Pulley remover I had on hand was not enough to get the job done. I knew the power of the special tool from my previous experience of removing a bicycle without a co-sauce, so I searched for it and found this YamahaOEM tool at a reasonable price. The feeling is that there is no rattling, and I can put a lot of power into it. However, it didn't shake, probably because it was an old motorcycle, so I applied more force with the Expander and was able to remove it safely. There was no sign of overworking the tool, and I am glad I purchased it. View detail
Easy to use
Purchased for Small TypeRatchet, cost performance is high with Holder set. Easy to use even in tight spaces. View detail
Purchased for Torque wrench
Purchased for Torque wrench. However, the Holder cracked rather easily if I didn't pinch it properly. View detail
Torque also has a Quantity:Set is convenient
I wanted a Torque set and found the other SK11Socket easy to use, so I bought this one. View detail
Maintenance
Quantity:I was contemplating the purchase of a set tool and it was on sale, so I didn't hesitate to buy it.
The glossy finish gives it a luxurious feel and the display is easy to read.
It is very useful for installation and maintenance of custom parts.
I think Spanner will be sufficient for some work.
The stop Bracket of the lid is easy to come off, so I made it functional Minus 1.
View detail
![Axle shaft sockets [4 sizes]](https://img.webike-cdn.net/catalogue/images/95068/yk022001_TS.jpg)
Necessities
Purchased for front axle shaft removal and attachment for tire replacement on GSX-R1000. It is very accurate, perfect fit, and safe to use. View detail
Small Water Resistant Paper 100pcs.
Large size is easy to work with, even for small scratches!
Outclassing is a pre-treatment for Motorcycle Cowl before painting!
This Quantity:Set has made a lot of progress in preprocessing!
I would like to buy again.
Thank you for the Large change!
View detail
Small but...
It was smaller than expected, but considering the purpose, it is natural that it was small.
I bought it for another purpose but I am satisfied with YOSHIMURA Logo.
View detail
Inexpensive but effective parts
The fastening Bolt of BMWOEMBrake Caliper was rusting, so I replaced it with Titaniumium Bolt from Rise Corporation during Overhaul.
A certain Oak Auction has a Bolt made of SUS304 Stainless Steel for Caliper fastening, but considering the fracture strength of the material, I think it is very dangerous and has a high possibility of breakage.
This Titaniumium bolt should have no problem in terms of strength, and the screw threads are beautifully machined.
View detail