Reviews
Fits: HONDA CB50, HONDA MONKEY, HONDA DREAM50, HONDA DREAM50, HONDA DREAM50, HONDA SUPER CUB 50, HONDA GORILLA, HONDA APE 50, HONDA APE 100
It is used infrequently.
It is still easier to use dedicated tools. View detail
Required for Flywheel removal
Used to loosen the center bolt when removing the flywheel.
Functionality is fine.
The restrains on the Adjustment Bolt were reluctant to move and could not be fixed properly without support.
View detail
For Motorcycle commuting to school
Purchased for Motorcycle to use to get to school in the rain. Never used.
Tools are not objects, so the molding is what it is.
View detail
It's good enough unless it's really sticking or something.
This is very useful if the Torque can be removed without applying that much Torque.
It is a good choice for many sizes, so I would say that this one is all you need.
However, if it is super sticky, it is better to use a shape product that can use Impactetc. instead of this kind of Type.
If you extend it with Pipe and apply Torque, it will indeed bend.
View detail
Protection.
I purchased this product to protect and prevent scratches and scuffs on the Exhaust System part.
It is thick and seems to be heat resistant, so I am installing it with high expectations.
I hope it will be somewhat durable, sticky, and long lasting.
If the size were a bit larger and cheaper, it would be helpful for consumables.
View detail
Maintenance
I purchased this product for maintenance of Clutch Wire. View detail
No problem
Used to replace Plug in LITTLE CUB.
Clearance was also of minimal quality and was replaced immediately with no problems.
Personally, I rarely use on-board tools, so I think this is about right.
View detail
Spring Remove
Used for Spring Remove during Chamber maintenance.
Since the price was not that expensive, I thought it would be better to have 1 pc. and bought KITACO.
Difficult to remove, difficult to use the handle part turns when force is needed? Is it good or bad? It seems like it would have been better if it was an integrated unit.
View detail
Buy it.
I bought it because it was inexpensive, but I had to do some additional work because I could not use it on my KTM250SX-F. View detail
If you have it, it's safe.
OEM parts are expensive, so I used them on my Z125PRO.
It is used only to prevent the clutch from turning when assembling the clutch.
Some people bite on Wrench or something, but it's too late to do it after it's broken.
View detail
AGUSTA
I purchased this product to prevent Cowl from flapping. I am glad that it is more firmly than I expected. I was able to adjust the length and widen the hole diameter to about Large. It is a pity that Red and Blue are no longer sold. View detail
Not when it's hard...
It is difficult but useful when the Plug is sticking. View detail
for Replacement
I bought this one to try for Hose clampfor Replacement.
Stainless SteelMaterial is good, but hang to remove, hard to do if you are not used to it? It seems to be.
It would be easier if the Clip end was a little larger.
The quantity is also half, Quantity:It would be helpful if it was cheaper at about 5pcs.
View detail
Good, but not great.
I'd like to get a Torque wrench, but I'm not sure if it's a cheap one from Home centeretc. …
I think it's good for people who
I think the range of Torque measurement is also just right for Motorcycle.
The only complaint I have is that it is difficult to understand the feeling of the power escaping when you reach the specified torque.
It's not a problem once you get used to it, but it may be confusing at first!
View detail
so-so
Just enough to get the dirt off.
It's not a wire brush so it's going to be tough to remove the rust.
View detail
For Gasoline Refueling
[How is it used?
I bought this for Gasoline refueling at Circuit.
I use it to calculate fuel consumption and to set the fuel to the smallest limit before the Race.
Was the one you received as per Image?
Image is correct, I use the same one for Oil.
How was your experience with it?
It has become the most recommended jug with lid and Cap at the end.
Garbage is hard to get mixed in, so the one I use with Oil won't get covered in dust and junk as long as I keep the lid tightly closed.
[Points to note]
When pouring, be careful not to close the mouth tightly or it will leak.
How did it compare to other products?
I recommend it with a lid and a Cap on the end to keep it clean and ready to use.
View detail
Expected
[How is it used?
I used it only once to change the engine oil.
Was the one you received as per Image?
It was smaller than I thought it would be.
How was your experience with it?
Until now, engine oil has been used in the lower part of the engine.
I had to adjust it while staring at it, but it was better to put it in after measuring it well.
It's convenient and gives you a different sense of security.
However, one thing that I thought I failed was that my Motorcycle, SB250, was
You need at least 1.2Liter when changing Oil, so you need to divide Oil into two times.
It's something you have to put in.
1.I should have bought a product that measures up to 5 liters...
[Points to note]
The lid is attached as an accessory, but it doesn't close that tightly.
Not to be used for spilling liquids.
Use it to prevent dust from getting in during storage. (Failure to do so)
How did it compare to other products?
This is my first purchase of Oil Jug, so I have nothing to compare it to.
1.If you have a 5Liter product, buy that one.
View detail
The capacity of the 250cc Motorcycle is just right.
[How is it used?
Oilfor Replacement
Was the one you received as per Image?
It was stronger than I thought.
How was your experience with it?
With a 250cc Motorcycle, the capacity is just right.
[Points to note]
If you have a four-cylinder, large type, it is smoother to buy the Oil Jug of large threshold size.
How did it compare to other products?
Cheap
View detail
If you want to change the oil.
【good point】
An easy-to-use 4-liter jug.
Motorcycle Oil is Large body and this size is just right.
[Bad point]
nothing special
[Summary]
If you use a jug when you change the oil, it will be less likely to spill and
You can manage the quantity properly, so if you often replace it yourself, you'll want to have it.
View detail
Flexible and unrestricted
If you drop a Bolt or Nut in a tight spot, the magnet makes it easy to pick it up when it's out of reach. It can be changed into any shape and is very effective. View detail