Reviews
You look good.
[How is it used?
XR230 Used for Valve Matching
Was the one you received as per Image?
Image
How was your experience with it?
We have completed the Valve matching process without any problems.
[Points to note]
It is a small package, but there is so much in it that you can't use it all.
No problem!
View detail
No wasting Gasoline
The Breather Hose 650mm 6mm Diameter on the tank cap of the KLX230R does not have a valve, so when it falls over, gasoline leaks out. However, I wanted to prevent leakage by attaching a valve to the tank cap to prevent physical exertion if I rushed to wake the tank cap up. Actually, I bought a Short Type with a Valve on the tip of the Hose before this one, but when I fell down, Gasoline dripped out of it. It is a pity that I cannot match the color with Kawasaki. View detail
I can't connect to the dedicated Site at all, so no.
If you don't improve Site, it will be useless. View detail
Solid easily adjustable but sprockets smaller than I required
This tool is multi-purpose; You can use it to remove the variator, flywheel, front sprocket and clutch. This was purchased to enable me to remove the front sprocket for bike. Although it did work, it was rather fiddly to use and the assistance of an additional pair of hands to held was needed. Product solid and quality.The tool itself is looks as though it will last long time. View detail
It backfired a little, but I was able to lubricate it successfully.
Lubricated when replacing Clutch Wire. Used Bell HammerSpray. View detail
Material:It is Stainless Steel, so it is durable!
[How is it used?
I bought it to replace the Split Pin on the Rear Tandem Footpeg and the fixed Bolt on the Rear brake.
Was the one you received as per Image?
The quantity is small, but the quality is fine, as per Image.
Was the installation difficult?
The Split Pin is simply replaced with a Split Pin for easy installation.
How was your experience with it?
Steel ones rust quickly, but this Pin is Material:It is Stainless Steel, so it will not rust and is durable.
[Included Parts:were they on?
There is nothing else as shown in the image.
[Was there anything that disappointed you?
Nothing in particular, but the quantity may be small.
▼ I would like to see One size and TwoSizeSmallest Pin included in the Lineup already.
View detail
Spring in one shot.
I purchased this product for use in Silencer replacement.
Before I bought this product, I had to struggle with pliers and my fingers to finally install it, but I was able to install it in one shot.
It is a part that I am tempted to be stingy with because I don't use it often, but I think there is no harm in buying it because it makes things much easier.
View detail
I use it a lot.
It is useful to have one. Used for minor repairs and electrical custom work. I have not used it for a long time, so I am not sure, but I think there will be no adhesive residue. It is very easy to use and I like it. View detail
Essentials for Hose Replacement
Fuel Hose hardens and deteriorates, but so does the Clip:Rust, broken, spreading. It's also cosmetically good! View detail
It worked!
[How is it used?
I purchased this to remove the Pulley area of my PCX125 JF56 as part of a drivetrain refresh.
Was the one you received as per Image?
It was solid and sturdy as per Image.
The weight was quite heavy.
How was your experience with it?
It worked normally. However, I think it was replaced by Air impact, so I didn't have much of a chance to use it.
I would use it again when messing with weight roller etc.
[Points to note]
How did it compare to other products?
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
As an old Motorcycle Spare
Since Fuel Hose and Fuel fliter were purchased, Band was also purchased,
Unifying Manufacturer gives a sense of security.
View detail
Challenge to Valve Matching
I bought this to Challenge for my first Valve Matching. I think it is good to try everything, but I personally thought that this area should be left to PRO. Also, I think it is not a good way to do it, but the Suction Cup is easy to come off from Valve. I think it is a good cosmetic product because it comes with two types of Compound. View detail
I have been using it for a long time because it has a good fit.
I have been using it for a long time because it has a good fit.
I usually use Black, but it seems to be out of stock, so I bought this one.
I am always worried about rust since it is not Stainless Steel.
Material of the same Size from before.:Waiting for Stainless Steel.
View detail
For automotive use
I have a short plug wrench of similar shape, Manufacturer unknown. It is easy to use for everyday work and I was able to use it on my previous CT110 HUNTER CUB and HUSTLER50 etc. I bought it for my car because I thought it would be good to have a similar tool on my new CUB90. I bought it for my CUB90 for my car because I didn't have an on-board tool for my CUB90, which I received as a gift.
I checked the difference between KIJIMA's new Wrench and the old Wrench of unknown manufacturer. The length is a fewmm shorter, but the construction is the same. Disassembling for storage is as easy as removing the bracket from the Wrench. This type of Wrench is a Universal Product, so there seems to be little difference even if the Manufacturer is different. To the old Wrench "Japan" but the new Wrench had no indication of the country of production on Body or Package.
I used the new Wrench with CUB90 to confirm.
Insert the Plug to remove it. The bracket that is inserted afterwards does not go in properly, and the bracket hits the leg shield. If you force it in, the WrenchBody is pushed at an angle by the Bracket and cannot be rotated properly. If I use it carefully, I can turn it, but it is not comfortable. If I use an old Wrench of almost the same size, I can turn it without any problem.
If you look closely, you will notice that the position of the hole where the bracket is inserted is different between the old and new Wrench. The new Wrench has the hole about 5mm inside of the old Wrench. This is why the bracket hits the leg shield when turning.
It is a little difficult to turn with my CUB90, but even with a CUB without a leg shield or with a leg shield, there is no problem if the mounting bolt and bracket on the bottom side are removed and the play is increased to a larger size.
KIJIMA may have designed the plug wrench not to drill holes where force is applied. A plug wrench is not designed to be turned by force all the time, but it may be used as a tool for other applications. However, it may be used as a tool for other applications. It is just my impression, but it is fun to think that there might be different reasons for the different designs of each manufacturer. There may be no significant reason. But I like to tinker with machines.
The new Wrench is fine considering its Large size, disassembly and storage, and the frequency of use of in-vehicle tools. I have tried many things and have figured out how to turn it. I will use it as an in-car tool as planned.
View detail
Peace of mind knowing the status of Battery
The battery for two-wheeled vehicles is smaller in capacity than that for four-wheeled vehicles,
Access to BatterySpace is so bad,
It is difficult to know Condition easily.
But with this product,
Highly accurate voltage information can be obtained via smartphone.
Use with Battery Charger,
Even Motorcycle without Kick starter,
We have been able to use the system without excessive worry about battery uptime.
The same product would be used on two Motorcycles,
If they are parked close to each other, there is a possibility of mixed signals.
If improved, it will be easier to use.
View detail
Chain cut easily and conveniently
[How is it used?
Purchased to Cut the Chain purchased with the Restore of the LITTLE CUB that was given to us.
I used to cut the joints of the Piece with an electric sander etc., but by using this product, I can easily chain cut in a short time, which is very convenient.
Was the one you received as per Image?
This product, which is used by our friends and our shop, is reasonably priced and easier to obtain than other products, and can be used for most chains, as it is available in 420, 428, 520, and 525 sizes.
Was the installation difficult?
It may be a little confusing when you are not used to it, but if you read the Instruction Manual carefully before working on it, you will be able to cut it really easily.
It is a safe place to keep in the toolbox of those who like to Restore and those who need Setting, including back and forth Sprocket.
How was your experience with it?
If you read the Instruction Manual carefully before use, the process will be easy.
[Included Parts:were they on?
All the items are shown in the attached picture. I don't know the name of each Parts, so please refer to the picture.
[Was there anything that disappointed you?
I have only used the product a few times, but I have no disappointment or dissatisfaction with the product as expected.
Other items that would be helpful
Point and hang of installation
On the bottom of the Instruction Manual. Cutting the bolt with a cut bolt will damage the tip of the bolt. Use a sander or similar tool to scrape off the crimp. Also, be sure to position the pin so that the tip of the pin is in the center of the crimp. It is stated that
To be honest, even if you use this product out of the blue, you can cut a 420 or 428 size without any problem, but if you want to use the tool for a long time, you should use it according to the Instruction Manual.
If you are still not confident, do not hesitate to ask for a PRO.
[Notes]
With this product. "Disking operations." It is only a tool to Cut Chain.
Please make sure to confirm the number of pieces to be cut in advance to ensure that there are no mistakes.
If you make a mistake and cut too many pieces, the chain will be too short to use.
Also, do not reuse a chain that has been stretched by overuse until it is cut, because the spacing between the pieces has also been stretched, which may lead to wear and tear on the sprocket and damage to the chain even if its strength is within the manufacturer's recommended engine displacement volume. The spacing between the pieces has been elongated, which may cause the Sprocket to wear differently.
[ITEMS TO BUY TOGETHER
A new Chain, each Chemical product needed for its maintenance, and Dustcloth are also useful.
[Opinions and requests to Manufacturer
Please continue to sell this product as long as possible, as it is easy for buyers to afford with Reasonable pricing and a wide range of uses.
View detail
nonfunctional
I understand that you use a syringe to decompress the Tank and suck it out.
It does not work at all.
In the end, it was a normal Air extraction while holding Lever.
View detail
Used in RZ250 Fuel Hose replacement
I also bought Clip to go with KIJIMA's Hose that I purchased.
I matched it to the diameter, but did not use it this time for fear of Gasoline leakage because the Clip was not nearly as effective as the diameter of the Cook's Nipple when it was installed.
The same product is bundled with KIJIMA's Hose that I purchased, but the diameter of the clip is slightly different from this, or maybe the included clip works properly and is usable.
I bought it with peace of mind because of the claim that it could be used with phi;00 Hose, but this time it was a disappointment.
View detail
Bottle will be dented.
I purchased this product because I wanted to do the Fluid replacement myself.
As per everyone's impressions, use a syringe to set the Bottle's air pressure.
If you lower the Lever, the Bottle will be dented.
It may be better to work while niggling.
View detail
Harnessfor repair or minor tear repair of sports bags
The harness tape on the bottom of the tank deteriorated after six months, so I chose this one, although it is a bit expensive.
As a result, I was generally satisfied with the texture (I had imagined it was stiff like E Corp.'s Binding Tape until I actually received it).
The adhesive strength is solid, and once it is applied, it cannot be removed easily, so it can be used in tough places.
It seems to me that the method of reinforcing little by little while shredding rather than rolling all at once is more suitable.
However, it is not flexible and cannot be used for moving parts. If you want to use it for moving parts, it is better to wrap it with Cell Wrap and use this Tape for fixation.
This is a slightly unusual use, but it can also be used to repair a slightly frayed sports bag, etc.
Waterproofness was not specified, but it is expected to be waterproof enough unless the product is constantly immersed in water.
View detail