Reviews
Heat and scratch protection
The evaluation did not seem to be bad, so I bought it to try it out.
Since it seems to have high heat resistance, it is used to prevent heat deformation and scratches on the inside of cowls. The price is not that much, and there are a few meters, so it can be used to some extent. I would like to check the adhesiveness for a while.
View detail
Protection.
I purchased this product to protect and prevent scratches and scuffs on the Exhaust System part.
It is thick and seems to be heat resistant, so I am installing it with high expectations.
I hope it will be somewhat durable, sticky, and long lasting.
If the size were a bit larger and cheaper, it would be helpful for consumables.
View detail
Since it can cut in a favorite form easily and a rear face has an adhesive, it is good to be able to stick immediately. I think that sticking on a deep curved surface is unsuitable since it is thick. A glass fiber is torn easily. A glass fiber
Since it can cut in a favorite form easily and a rear face has an adhesive, it is good to be able to stick immediately.
I think that sticking on a deep curved surface is unsuitable since it is thick.
A glass fiber is torn easily.
A glass fiber may be stuck in the skin and there is CHIKUCHIKU [ it ] since [ thin ] it is hard.
CHIKUCHIKU when touched empty-handed.
I think that it is easy to disperse in the air lightly like the fiber of feathers since it is light.
I think that handling requires cautions enough.
Silicon coking was given to all the cutting planes after sticking on a cowl, since the glass fiber of the cut-off cutting plane was torn easily.
View detail
Highly effective insulation
Wrapped so that the heat from the exhaust pipe does not affect the Cowl, etc.
Stainless Steel Wire is included for secure wrapping.
The heat insulation was also very effective and mitigated the heat.
View detail
It's good to have some comfort.
[How is it used?
It was just installed the other day. Practical durability performance will be verified in the future.
Was the one you received as per Image?
It is close to Image, but the thickness is thinner than I imagined w
How was your experience with it?
After I changed to Earls Gear's Full Exhaust System, I was worried about heat distortion of Lower cowl because Exhaust pipe, RightLower cowl and Clearance became narrower. I found this insulation tape on Webike, so I tried it. I found this insulated tape on Webike and gave it a try.
Easy to apply and perfect adhesive strength. Because it is not thick, the tracking of the curved surface seems to be good.
But what about the important insulation performance? This is my feeling.
[Points to note]
Since it cannot be reapplied, the surface to be applied must be thoroughly cleaned and degreased.
How did it compare to other products?
I haven't compared them because Webike didn't give me any other choice. However, the OEM insulating seat material on the lower cowl of Kawasaki ZX-14R is quite thick, so the insulating effect may be a little less than that.
Other items that would be helpful
It is better to prepare the cleaning tools such as Silicon-off and Parts cleaner.
It would have been nice to be able to choose the thickness of the Heat Insulating Material as a product Variation.
View detail
At least it's insulated.
I bought it to wrap around my 2-stroke Chamber.
Wire and wire twister are necessary. It is necessary to make the appearance beautiful. It becomes a heat-shielding, but I am not sure whether the performance has improved.
View detail
[Webike Monitor] Since the sheet was hot, it stuck on the back side. if it runs for 2 hours although the sheet becomes difficult to get hot -- -- it is ineffective. I thought whether it was Massey whether it is the lay which is not.
[Webike Monitor] Since the
sheet was hot, it stuck on the back side.
if it runs for 2 hours although the
sheet becomes difficult to get hot --
-- it is ineffective.
I thought whether it was Massey whether it is the lay which is not.
View detail
It has a rectangle of 5 cm x 100 cm, and since the flesh side of pasteboard is paper, it can use a Magic. since -- it is best to make and cut off a model. Thickness was stuck inside the Undercowl so that it might not melt about 1.5 mm with the heat of t
It has a rectangle of 5 cm x 100 cm, and since the flesh side of pasteboard is paper, it can use a Magic.
since -- it is best to make and cut off a model.
Thickness was stuck inside the Undercowl so that it might not melt about 1.5 mm with the heat of the
[attachment and the effect
] and a Muffler.
The marks where the Cowl and the heat insulating material burned are nothing so that the heat-resistant effect may be enough.
It stuck on the Carbon sheet of
.0.3mm, and stuck it on the Rear frame.
When it sees targeting the exothermic fall from a Frame, heat is felt although it came to touch empty-handed.
Since it was thick, the
[general comment]
and thickness have expected that the heat-resistant effect was 1.5 mm.
Since it is merely a rectangle, it is troublesome to make a form.
View detail
Since a muffler and cowl were near, I purchased for preventing heat purpose. It is as expected.
Since a muffler and cowl were near, I purchased for preventing heat purpose. It is as expected. View detail
Since the accident in which it melted in an instant when a rainwear is equivalent to a muffler, since the muffler was replaced with the custom muffler occurred, in order to carry out somehow, it decided to roll this tape. Melting at the moment of [ th
Since the accident in which it melted in an instant when a rainwear is equivalent to a muffler, since the muffler was replaced with the custom muffler occurred, in order to carry out somehow, it decided to roll this tape.
Melting at the moment of [ the ] touching safely, although it was operative was lost.
Although it was good, even if it rolls this, to the extent that it cannot touch by hand yet becomes only temperature.
Don't you carry out as perfect heat insulation as a pure muffler?
This product is a double-stick tape type in practice, although wire is reflected with the photograph.
It is better to check in written form firmly.
It is the adhesive power of the grade of being easy to wind since a double-stick tape type adheres when twisting, and too, if an end is not pressed down with wire, it will separate.
About nine months have passed since it wound, but surface silver separates and a lower white portion is becoming unreserved.
View detail
Work good considering a price is done and there is well. Work is also easy and should just have scissors. I wound around the brake hose passing through the neighborhood of piping of a muffler. Although it is unknown, isn't it profitable which
Work good considering a price is done and there is well.
Work is also easy and should just have scissors.
I wound around the brake hose passing through the neighborhood of piping of a muffler.
Although it is unknown, isn't it profitable which actually works if big sense of security can be got in this amount of money?
View detail