Reviews
We're using it to our advantage
Although it's not a regular use, Straight (STRAIGHT) It is installed on the Rear Stand of a manufacturer
It's perfect I have no complaints
In the L-TypeArm, it interferes with the exhaust system and (In my motorcycle.) The STAND itself was not available
But thanks to this OffsetArm, I didn't have to throw away the STAND
The arm's insertion point is just 20mm per side, and it's tight, but it's straight and I was able to plug it in while tapping it lightly with the Hammer
OffsetArm is also available from Ethos Design, but that one is 25 it is not compatible with the Straight and AstroDacts Rear Stand as it is too small for the Straight and AstroDacts I didn't buy it
The shape of the Rubber uke part is round, but there was no slippage when I lifted it
(I don't know if it will deteriorate... But I don't mind if it doesn't.)
Also, is it because the Straight's Rear Stand originally lifted the body slightly higher? and OffsetArm, the power required for the lift has increased
It's too much trouble, so I have to ask for help from others, but if you do it alone, be careful not to knock the car over It seems to me that the
The texture is rather lumpy, the welds are solid and look strong
I guess it's not too expensive for 2,000 yen a piece for this quality
Since I bought it, it will be the rainy season from now on, ChainMaintenance I will do my best not to skip it
View detail
Is good
It's J-TRIP's Short roller stands so it's the one to buy
I bought it for a CB without Hook
I wish I had bought it sooner
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
ZrX1200ZrX1200Lift up ZrX1200 DAEG with ease, Large I'm satisfied!
Before purchasing this product, I had had it for some time
VHook Uke, Lift the ZrX1200ZrX1200 DAEG
I have tried to up, but the weight is too heavy
It didn't go up at all
So, I bought a ZrX from We-Big
I used this product, which is specially designed for this purpose, and it was easy to lift
We're up!
It's as good as the ZrX, and the texture is good, and the construction is
I am very happy with it
View detail
Fits: DUCATI 1098, MV AGUSTA Cantilever Swing Arm All Cars, DUCATI 1098, MV AGUSTA All models with cantilever swing arm, MV AGUSTA All models with cantilever swing arm
too expensive
Although I purchased it without any help even if I searched for others, 7700 yen was too high for just iron bar. Accuracy is unquestionable to fit in STANDBody, but Motorcycle shakes with considerable width, whether it is too thin with respect to the hole on the hub side with the Motorcycle Lift. I thought that I would collapse for a moment and chilled the liver. In the case of cantilevered swing arm it is unknown whether this is normal, but there is no Merit that uses Tire as much as it can shake so much. View detail
It became easy to use
Since I used L-Type receiver in the past, it was not easy to STAND-UP like Swap Arm and still not Gap according to Swing Arm.
With this product, setting ? Both STAND-UP have no anxiety, even those who are new will be able to use easily.
View detail
Appropriate or inappropriate by Motorcycle
I bought and used Nanja 1000 for the Chinese character,
If you do not pay attention to Stand Hook Bolt, it interferes with the heat-resistant Plate of the Exhaust System and interferes with the interference or Swing Arm, so I need to be careful. I tried including HEMO bolt including various OEM products, but it does not go well.
Cutting of heat-resistant Plate may be the best.
That is why I used the character bracket, but care must be taken when using it. (OEM case) I will hurt you..
Right Side is like Quantity : The place to set is limited, attention is required for Rear brake Pipe.
Left Side is Quantity : If the place to set is too far forward, it hurts the Exhaust System and it will hurt.
Different from character receipt Quantity : It is easy to shift back and forth when setting (Since there is Hook bolt, it is not shifted back and forth) , Quantity : Pair (for Left and Right) As we can easily shift about, we must be careful to be parallel with Tire (Even if it is silent letters are made parallel) And before and after Quantity : Pair (for Left and Right) And need attention. Actually the corner Pipe hit the Exhaust System and the bottom of the Exhaust System dented.
Although the OEM Hook bolt is shown in the picture, it is installed in a way different from the original so as not to go before getting a letter hit.
However, since Right Side has Pipe of Rear brake, it is not useful..
Although I am using J-trip by trial and error as above, Exhaust System exchange may be the best solution
Conclusion is that NINJA 1000 needs sufficient attention to use, it is not used in winter keeping.
Eliminator 125 can be used without any problems.
View detail
It's a nice product.
"JTrip for the first time STAND" I was using
Because it became necessary to remove Rear tire
I purchased this item.
I thought of receiving V
Hook boltetc. It is also necessary to purchase
I made this product.
Product L2 - There are 42 kinds.
Do not make a mistake
View detail
If you purchase unit's Rear stands, please come with us!
I do not know how it is now but when I purchased unit's Rear stands the L shaped hook was standard equipment.
This L-shaped Hook is a thing that is hard for me to use, perhaps Engine Displacement Volume of Motorcycle (weight) I think that it is hard to use in proportion to - - -
Motorcycle of Ritter Class will bow and become unstable.
So, if you are planning to use it in Large Motorcycle, I think that it is better to have this U-shaped Type absolutely.
In fact, the U-shaped Type was stuck firmly and felt stable.
As Demerit, it is necessary to create a Hook bolt in Swingarm and the U shape Hook is made by Gold Genre and it is BALIBALI, so the above mentioned Hook bolt becomes garish.
Well, it's not a big problem.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
ZrX Without this.
As expected it was exactly as it is written exclusively for ZrX.
You can Lift up without difficulty.
Just to say difficult, the tip Rubber cover is easy to take off, when you can notice it when you take it, but when you do not notice it
It seems to be lost.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
It is sold separately, expensive, and it does not have a good texture.
Required for Maintenance of ZrX1100. I bought it together with Short wide Body.
Basically I can lightly lift without problems at all. It is very convenient and frequently used.
However, ZrX requires this dedicated hook, the discount rate is low only for this hook, and the result total Gold amount is quite expensive.
As this Hook, Plating Specification I bought it expecting rust prevention, but when I look at the actual thing Plating seems to be thin, this is worrying about durability. I see the state while regularly rust-proofing.
Also, although others have been pointed out, the Red Protection Rubber at the tip easily falls off. From now on think about handling such as binding with Tie Wrap.
However, since it is necessary to Lift ZrX, I do a good job with Body Set, so I recommend it to those who do ZrXMaintenance.
View detail
Fits: KAWASAKI NINJA H2, KAWASAKI NINJA H2R, KAWASAKI Ninja H2, KAWASAKI Ninja H2R, KAWASAKI Ninja H2, KAWASAKI Ninja H2R
Good
Things are very good but expensive
Since it can not be Lift up without it, it can not be helped, but is not the price setting too appropriate compared to other Size?
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
I think that things are solid.
Since I did not use the exclusive thing before lifting ZrX with Maintenace Stand before, I knocked down. Also, I did not do the same thing so I bought it. I have not used it yet, but I think that I can work safely with this. View detail
Firm making
When I lost color of Front stand and I was at a loss, I found out the existence of this item and purchased.
Can be used without problems, quality is better than the original one. Lineup of such Parts is appreciated.
View detail
A round bar of free is sufficient.
Let me up when I lifted Motorcycle and it bent a little. I can not believe it's a light Motorcycle. Just buying a round bar with Home center is sufficient.
Usability is not as easy as I thought.
View detail
There is a sense of stability
It is wide and easy to hang on Swingarm and is convenient to use. However, Cover will be damaged if it is used for a while, so it seems better to have more thickness and strength. View detail
Fits: DUCATI MULTISTRADA 1000DS 1000, DUCATI STREETFIGHTER848, DUCATI MONSTER796, DUCATI Multistrada 1100/S, DUCATI MONSTER1100EVO, DUCATI HYPERSTRADA, DUCATI MONSTER1100/S, DUCATI HYPERMOTARD796, DUCATI 996, DUCATI 998, DUCATI 848, DUCATI 916, DUCATI 748, DUCATI 748, DUCATI 848, DUCATI 916, DUCATI 996, DUCATI 998, DUCATI HYPERMOTARD796, DUCATI HYPERSTRADA
In conjunction with BabyfaceSlider, STAND is available
Although it is originally Φ 41 for panigale,
In my case, with Rear slider attached
Because I wanted to use Maintenace Stand,
I chose Φ 26.
(Only Babyface's Slider corresponds to this)
Follow the instructions of Babyface's HP
I bought it, but as a result there was no play
It matches perfectly and it can be used with confidence.
Degree of Lift up in STAND,
To those who are troublesome to detach Slider
This combination is quite a Recommendation.
View detail
OK!
Vehicle is heavy, it is ZrX1200R which is difficult to raise. V - Up height was less than L receiving, and I was able to raise it overwhelmingly lightly. Hollow Shaft & I was thinking about receiving it for the first time, but discovering here and buying it was a correct answer. I thought that JTrip made a nice thing, but the price setting is too expensive. Recommended for those who are riding in the ekensen motorcycle. Risk at the time of Up and feeling of fear almost disappears, and it can be raised as a hyo. Up for the first time will be the same feeling. Since Tire can not be removed, do not throw away the L receiver and do not have it View detail
For light weight
When we diverted it to heavy-duty cars by other manufacturer's FSTAND, Adapter bent.
Up to 400? Class may be the usage limit. (Adapter diameter : 13mm)
So, let's avoid diversion. Let's keep using FSTAND of Body's Ethos to a light vehicle.
View detail
It is easy to use
Although I was using V reception, because I changed to a cantilevered swingarm vehicle, purchase Receptor Set for Beginner additionally.
I can lightly STAND-UP, I am active in car washing, ChainMaintenance.
There is also a cantilever STAND of other Manufacturer, but STAND with J-TRIP Roller is easier to use.
View detail
Great and relieved
【What made you decide the purchase?】 I had JTrip's MaintenanceSTAND
【How was it actually used?】 It is possible to keep STAND-UP steadily since Head can be kept in parallel with Swingarm at all times by turning Large Large than you thought.
There is a sense of stability that seems to be usable without problems at all if it shakes a little.
【Please tell us the point of use and hang】 First of all, it is better not to push the reception width exactly according to the width of Swingarm, not to extrude Motorcycle forward, but I think that it is better to lift STAND up and turn it down quietly instead of pushing forward.
(Even though I tried to extrude Motorcycle in front and pay STAND at the feet, the head of L receiving sticked to Swingarm and it did not work well)
【Hope for Manufacturer - Please let me know if there are any improvement points】 If the resin part of Head gets caught it will be saved if only the resin part can be exchanged cheaply.
【Have you compared items?】 Absent
View detail