Reviews
There is a sense of stability.
Once you first position it is easy from the next.
L The resin of the receiving part is thick and it does not slip
It firmly supports Swingarm.
I think that it will not be scratched unless you set it with a funny appearance.
There is a sense of stability that does not move even if it is slightly shaken.
View detail
It is added.
Motorcycle Shifter purchased with Single Item but I bought it along with the increase in Motorcycle, but it was easier and faster to store Motorcycle than there was not available.
I thought that it was better to purchase with Set from the beginning.
View detail
Because I can not use V letter receiver, it can not be helped - - -
Purchase to use Maintenace Stand at MT-07.
STAND used Mini bike for V letter receipt.
Since MT-07 can not make V letter receiving usable, I purchased the item now.
Until now it was V-shaped with a lightweight Motorcycle so Motorcycle is Large and L-shaped, so it's hard to do STAND-UP.
I have to get up and get used to it.
View detail
It can be used without problems.
Grom is purchased because it only accepts L.
I was anxious at first, but it will rise without problems if I get used to it.
I'm putting Swingarm firmly, so there is no problem shaking it somewhat.
View detail
Fits: DUCATI 1098, MV AGUSTA Cantilever Swing Arm All Cars, DUCATI 1098, MV AGUSTA All models with cantilever swing arm, MV AGUSTA All models with cantilever swing arm
If it is a bit thicker - - -
Purchased with JT - 136 cantilevered STAND and Set with AGUSTAF 4 purchase.
It is a pity that looking and making is good, but the Shaft diameter is narrow with respect to the Axle hole on the car body side, and shaking the car body with the lift up state is pretty good to be glazed.
Perhaps it matches the Axle hole diameter of Ducati ???
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
Cover at the tip tends to come off.
Although there are also writes of others, Red Cover at the tip is easy to disengage, and additionally it has torn. I hope that you can make improvements. Other than that I am satisfied.. View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
"easy" It is attached to one word of.
I used Kawasaki OEM's Maintenace Stand, but because I have a lot of steps to stepped in, I decided to buy this time because it will become unstable when I Lift and I will beat a single car. It is as easy as the title. When using the HOOK Hook attached to the hollow type Axle Shaft or EccentricColor Removing the Tire etc etc. There is also Maintenance which can not be done, but here is no problem at all.
Although the evaluation of the product itself is five stars, since the price is higher than the usual V letter Hook, it made it to four. In addition, the STAND of Kawasaki OEM is not compatible as the mounting part of the Hook is 25 mm square and the J-TRIP is 20 mm square.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
It is exclusive for ZrX
It is a title street, is not it?.
Previously I had MotorcycleLift with ordinary V receiver.
There is nothing I can not do Lift.
But when you Lift Tire will rise dramatically from the ground.
You can also Lift "It will lightly rise" I was thinking that it is like this.
Again, exclusive items are different.
Before replacing it with an exclusive item, there was unstable Timing from the start to the completion of Lift, but it became possible to do without anxiety until it came up to Hook.
Since it is a moderate upward width, you can lift lightly from Dosun to Side Stand when you cancel.
Why are you thinking really well?.
Although it is in the Impre of the other person, there is a sense of welding place in proportion to the price.
There is no problem with the function.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
Exclusive V Received Set for ZRX
J-TRIPJTrip Exclusive V Received Set for ZrX
Also purchased here for Rear stand purchase.
There is an expensive feeling for Set purchase.
I'm still happy if the price is a bit cheaper
View detail
Stabilize
I used the old STAND of ETHOS, but because of Swingarm shape of Motorcycle, the hook was sweet and unstable in Rubber reception, so I made it a combination of V order Arm + Hook bolt.
Truly OEM. Fixed part is perfect.
It will also stabilize when it is set to V, and since it will not escape when making a STAND-UP, it is easier to work.
View detail
Fits: DUCATI Panigale 1199/1098(rear)/1198/STREETFIGHTER1198/Deer Bell MULTISTRADA 1000DS1200 MONSTER S21200/Setc., DUCATI Panigale 1199/1098(rear)/1198/Streetfighter 1198/Diavel Multistrada 1200 Monster 1200/S etc., DUCATI Panigale 1199/1098(rear)/1198/Streetfighter 1198/Diavel Multistrada 1200 Monster 1200/S etc.
For replacing the vehicle
Since we switched from MONSTER 1100 evo to 1200,
I bought only Shaft.
Because the STAND itself was extremely useful even at 1100
I think that there is no loss to bring.
Just like others' impress
We are worried that the weight of the vehicle has increased, while Shaft's cost is low.
I do not think there is anything wrong - -.
View detail
Danger! Unstable! Purchase well thought out
I used it attached to Hazimete STAND
Anyway it is dangerous, unstable
When raising the car body the aim is not settled at the receiving part of the letter L.
As a result, the Gold genus of the L-letter touches the Motorcycle
Originally, I made scratches on the part that could not get scratched.
Also, I myself hurt while raising and lowering myself several times.
Manufacturer says that even if one gets used to the movie alone, it is said that it can be done alone, but in the case of using this L letter receiver, it is different.
This advertisement itself is an act of fraudulent act.
Large If you do not want to scratch your motorcycle
Anyway buy carefully!
View detail
I am happy that consumable parts can be purchased with Single Item
"Receiving part separately sold Type" Because I bought Rear stand of, it will be sold separately this time.
I am happy with Polished. I want to use it forever
View detail
Reception is thought to be a firm thing
I think that receiving STAND is a firm thing.
I tried to divert it in other STAND but Size did not match.
Clearly, because the shapes were similar, I thought that it was just an OEM product that changed Seal.
For your reference
One side : 21 mm square
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
For maintenance ...
I bought it for maintenance. It is Large strange to lift alone until get used to, but it is useful when cleaning Chain. I was doing while moving so far, but I was able to clean it while turning the rear wheel round and round with confidence, so it became very easy. After that is a little cheaper Star Quantity : 5pcs. is not it. View detail
It is purchased for for Repair
I use Ethos' STAND, but the shape of the nail Hook is the same so I'm covering it. Tie wrap keeps the root narrow so as not to come out. In this package we recommend using double-sided tape inside. Quantity : 1 Set of 4pcs. However, I think that it is easier to use on two sides of Hook's long claws on the Motorcycle side.
View detail
For DAEG
For ZrX1200DAEG
I got a JTRIP Front stand, but bo SCHOLAR Knife is out of stock.
Check Size and purchase 15 mm as Single Item.
It was cheap and saved..
View detail
Surprisingly easy to use
I used STAND for the first time. It was a little uneasy because the area of ??the receiving part was small, it was unexpectedly easy to use when used, and I was able to support Bike with confidence. View detail
Maybe I did not need it
Attention is necessary when using with Small Motorcycle.
The width of Swingarm is small and it can not be used unless it spreads quite inside like the attached picture (Using Jtrip's Short Type STAND) It is slightly unstable and scary.
With some Size Motorcycle, it will be useful under the condition that Hook bolt can not be used, but I do not think so much such a stuttulation.
The thing itself is solid and solid Cover of resin is considerably thick, I think that it will play a role in preventing Wound, and the sense of rigidity is also moderate.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
It was necessary for Lift up with MaintenanceSTAND.
It is necessary to receive Lift up at Garage.
Lift up with Hook bolt as V pick up and scoop up. Because it is exclusive for the car model, there is only use (^^) The V receiving position was adjusted horizontally according to Hook bolt. There is anxiety about loosening because its fixation is due to hand tightening screws. There is no problem at the moment. Rubber at the top of V receiving is cautious as it is easy to remove. I think whether there is a particular problem as long as position adjustment is done from the horizontal state for Lift up.
View detail