Reviews
damage
As you can see in the photo, the spring and functioning part of the component was damaged from the start.
I assume it is fabricated by cutting from a board.
If it is to be used as a spring, I think it needs to be heat-treated, but I guess it hasn't been.
There are welding areas nearby, so the heat from the welding may have an effect.
I think it's a product with a high breakage rate.
View detail
Defective item
When I looked at the product sent to me, the spring part was damaged as shown in the picture.
I assume the parts were cut from sheet metal.
If they were to function as springs, they would need to be heat-treated or something, but I guess they haven't done that.
The heat from the welds may have an effect, and I think the product has a high defect rate.
As for DAYTONA's STAND, the front stand has recently been voluntarily recalled.
I don't think they are made in-house, but as long as they are sold, DAYTONA needs to take responsibility for quality control.
View detail
It's a very good idea…
I bought this because I was worried about it coming off when I lifted up in the V by myself.
Since the Hook and the receiver are fixed, the sense of security is perfect, but the moment I lifted up, it was torn off.
Did I use it incorrectly?
But I understood how it works, so I bought a slightly thicker Rubber Band at 100 yen and wrapped it so that it would be fixed in the same way.Rubber Band is cheap even if it breaks, so I started using Rubber Band after that.
View detail
easy
Used for ZrX1200R.
Shaft bent easily.
Disappointing
View detail
It broke on the first try
It's a cantilevered vehicle with 230k miles on it, and it broke on the first lift up
I was worried that the shaft is too thin to be threaded through, but it was no good
I bought it after seeing a review of my use of cantilevered and 270 pounds Was it bad?
View detail
It's hard to know what kind of car it's for
I bought a body and V receiver for maintenance on my CB650F
After purchasing it, I noticed that the body of the car does not have the for Swing ArmHook mounting screws
I didn't check myself enough, so I gave up
I have now purchased the L-Shaped Receptor
So, here's the problem again..
Use for 400 CC or less on the product you received in the mail It says
Then I think there should be an explanation to the L-Shaped Receptor before ordering! But what do you think? I bought it with high expectations because of the good reviews from everyone on Maintenance StandBody! But I'm disappointed 。 It's a shame that I can't send it through WeBike's exchange or contact page, no matter how many times I enter the information
sad 。 I think it would be better if you considered a more detailed response
View detail
Danger! Unstable! Purchase well thought out
I used it attached to Hazimete STAND
Anyway it is dangerous, unstable
When raising the car body the aim is not settled at the receiving part of the letter L.
As a result, the Gold genus of the L-letter touches the Motorcycle
Originally, I made scratches on the part that could not get scratched.
Also, I myself hurt while raising and lowering myself several times.
Manufacturer says that even if one gets used to the movie alone, it is said that it can be done alone, but in the case of using this L letter receiver, it is different.
This advertisement itself is an act of fraudulent act.
Large If you do not want to scratch your motorcycle
Anyway buy carefully!
View detail
Maybe I did not need it
Attention is necessary when using with Small Motorcycle.
The width of Swingarm is small and it can not be used unless it spreads quite inside like the attached picture (Using Jtrip's Short Type STAND) It is slightly unstable and scary.
With some Size Motorcycle, it will be useful under the condition that Hook bolt can not be used, but I do not think so much such a stuttulation.
The thing itself is solid and solid Cover of resin is considerably thick, I think that it will play a role in preventing Wound, and the sense of rigidity is also moderate.
View detail