Reviews
I couldn't use it well.
I bought this tool because I am not good at putting the piston through the cylinder when assembling the engine of MONKEY. However, I could assemble the engine better by hand without using the tool, probably due to my lack of skill. View detail
Used for Clutch Cable!
Used for Clutch Cable of GB250 CLUBMAN.
I used an injector because the lubricant would fly out if injected as is. The GB250 CLUBMAN is not a heavy clutch, but it feels smoother. If you have an old car and the clutch is heavy, I recommend you to use Injector because the lubricant will spread to the whole Cable.
View detail
It's cheap and easy to use. But …
Cheap and easy to use.
But to be honest, it is not essential, because it can be inserted by hand without it.
I bought it, but it became a hassle to use it, so I had to put it in by hand.
View detail
Large amount of Split Pin
[How is it used?
The TZr250R uses split pins in several places, and it is a hassle to choose the right size, so I decided to use Quantity.:I was looking for Set.
Was the one you received as per Image?
As you can see in the picture, the Large amount of Split Pins were separated by Size.
How was your experience with it?
Compared to the OEM Axle Shaft Split Pin, it was a little thinner even though it was about the same length.
The thinness makes it easy to bend, and since it is not a place where loads are applied, I personally found it easy to use.
I think the legs are a little long, but it's acceptable.
[Points to note]
The 2Size Left has 150 sticks in one divider, so it's easy to go through the side dividers. LOL!
You need to check the size carefully when using the actual product.
How did it compare to other products?
I thought about buying the OEM one, but it's more expensive and I need to stock it for when I need to use it.:I chose this product that came in a Set.
If you know the size you want to use, you may be able to use the ones sold by Rose at Home centeretc.
【Review】
It comes in a large quantity and the price is not that expensive, so it is good to have one if you are a frequent maintainer or have multiple units.
View detail
The difference between having it and not having it.
I bought this for wire lubrication.
You can spray it on as it is, but it will make your hands dirty. It is a jig to spray lubricant between Wire's Thailand core.
good point
The wire can be lubricated with the appropriate amount of lubricant.
It can be used for any type of wire.
It is very cost effective.
A bad point
It will get dirty at least a little.
It may get your hands a little dirty, but there is a big difference between having it and not having it, and there is no harm in having it if you do your own maintenance.
View detail
You can use it.
First time I've used it.
It seems like a lie that it used to take me about 30 minutes to push it in with my fingers.
The instruction manual is not included, so the first time user may fit it upside down.
That's the only thing you need to pay attention to.
In case you're wondering, Piston diameter is Φ79.
View detail
Split Pin should be used as a general rule for a new product.
The RZ uses the Split Pin for the Front wheel and Rear wheel nut locks. Of course, it is possible to buy them from OEM, but the price and delivery time are reasonable. minimoto's Split Pin is 555ps and cheap. I used to take it off and reuse it to avoid breaking it, but I've been using a new one since I bought it. View detail
It's not a problem
MINIMOTOMinimotoThe MinimotoPiston ring compressor has arrived, so I'm going to give it to you I'd like to give you a quick in-play of how it feels to use it
I think the quality of the product is reasonable for the price range
It's safe to say that you won't be disappointed by the amount of gold you buy, which is Large
I bought the product and I don't feel like I'm losing money
As far as shopping goes, I felt like it wasn't a loss
It is a product worth the Gold amount
View detail
To use
I used it on my Kawasaki Z2, it works great, now I'll use it on my TDR20 I used to build without RingCompressor, but it's still easy, Home! I bought a aluminum block at center and made a PistonStopper by myself Then you can put in 4 cylinders with Scauper
View detail