Reviews
Tail Bulb replacement for KSR's Fender Eliminator Kit
I purchased a used KSR80, but the previous owner installed a Fender Eliminator Kit, and the tail lamp is a Lucas type.
There was a Trouble with Tail Bulb immediately after purchase.
I removed the Lens to see the model of the Lamp to replace it, but unlike the usual Double Bulb, the head was a Small Rhinoceros Bulb.
This Type was not sold at Home center or Car Shop 。 Maybe MotorcycleParts specialty stores have them, but I can't find any near me. 。
However, because the length of the Tail Bulb was different, it interfered with the Lens, causing the Lens to chip, melt, and consume more power due to its higher wattage.
I had put it off because it was inexpensive but the shipping and other things made it needlessly expensive, but I had some shopping to do at WeBig, so I bought it as a package deal.
After installation, there was no interference (obviously), and since the Watt number was lowered, the power consumption was also lowered, eliminating the concern factor.
I am planning to eventually switch to LEDs, but there is a barrier of full-wave rectification, so I may end up putting it off.
View detail
Japanese Vehicle Inspection Correspondence
Before the inspection of SR400, I went to the tester place off site to check the light intensity. I had to go back and forth to Tester two years ago, but they did it without any extra charge, I switched to the new Stanley Hyper Halogen LightValve, which I brought with me again. It is just 150mm away from the specified light level, but it is OK.... Hyper Halogen Light is a high efficiency valve and can be brighter with the same power consumption as the standard valve, but it seems to have a shorter life. View detail
LED Bulb from leading manufacturer
Stanley is a leading manufacturer of OEM parts.
I am satisfied with both the brightness and the spread of light. The picture was taken with the position lamp in place.
The original brightness of the Valve is brighter than the image because the brightness is set to low.
View detail
Fits: HONDA Dio110, YAMAHA CYGNUS X, Others , YAMAHA BWS125
For VSTROMSXBlinker Valve replacement
I purchased SP Mukawa's Plating Valve to fix the orange bulb that I could see through the OEM Clear Lens. The only thing I was worried about was the amount of light, but it is sufficient and looks Refreshing! View detail
Normal is fine.
Tail lamps that are always on are consumable.
Stop-lamps are still alive but replaced immediately when noticed to avoid maintenance failure due to trivial things.
We had thought about using LEDs, but we concluded that Standard was the best choice due to its cost performance and reliability.
In the case of DJEBEL, the OEM installed Carrier interferes with the approach of the Tail lamp cover to the Screw. This is where SEA BASS comes in:remove the rear screws from the carrier, loosen the front screws, and stand the carrier up like a Gal wing, and the replacement can be completed in a few minutes.
The durability of the bulbs is a matter of luck, but since it is a product of FOR JAPAN MODEL MANUFACTURER, it is safe to use for the time being.
View detail
For Stock
I have already purchased this product last time and bought it for Stock.
It's for old Custom parts,
In the countryside, items are difficult to obtain.
Thanks.
View detail
Tail lamp replacement for JOG for repair.
Tail lamp bulb of a 2-stroke JOG obtained through a private sale was broken and was replaced.
Lower price than Valve for OEM Parts, Quantity:1 Set of 2pcs.
I will only use 1 pc. and will keep the other one as a spare.
I thought about using LED Tail lamp bulbs, but since it is a 50cc moped, these are sufficient.
*Wattage should be matched to the OEM.
View detail
Indicator bulb out of service.
It was used due to a broken bulb in Indicator.
It's working fine
View detail
A very ordinary Halogen bulb.
Whenever I buy a used Motorcycle, I always replace all the valves with new ones, but since they were out of stock at my local store, I couldn't be bothered to come back to the store, so I bought them by mail order.
I thought the price might be a little higher than the actual store. I thought the price might be a little higher than in the actual store, but considering the time and effort involved, it was acceptable.
There is nothing wrong with the fit and there is nothing special to say about the color.
This is fine unless you don't want the Amber color to stand out over the Lens.
I thought it might be a good idea to purchase an additional one as a spare when I purchase some more Parts.
View detail
It was saved.
Large European blinker bulbs that were installed a long time ago were out of stock at home centers and car shops in the countryside, and there were no hits in the Internet search.
However, I loosened the search criteria and found it! Crying
Thank you for the help
I'll stock up next time.
View detail
It is safer to always have it at home with Spare!
The cheap Pine Stripe bulbs, but just one of these can cause a maintenance failure!
They run out without notice, so it's always safer to have one in reserve.
Depending on the model of car, the replacement work is a single +Driver.
View detail
Rare 6V bulb
I used it to repair a broken Neutral lamp on a VANVAN90 that was given to me by a friend's father.
Since it is an old motorcycle, there are no parts available, so the rare 6v bulb is a big help.
View detail
On a ball run out.
I bought this for replacement because the bulb was out!
It was fixed normally!
View detail
The abundant number of Watt will help.
I added Hazard and bought this one to lower the Watt number in terms of power consumption reduction.
It was really helpful to have Double Bulb as well as Single Bulb.
The abundance of Variation here is very good, as Motorcycle definitely does not look good with flashing LEDs.
View detail
Cost-effective
Used for POSH and Fath blinkers. POSH has Valve, but I bought this one because Mats Stripe products are much cheaper even though they are the same standard. I have used them on other cars and have confirmed that there are no quality problems, so I can use them with confidence. View detail
In fact, if it were an LED Bulb, I think it should be treated as Standard.
Single Bulb, which is likely to be used mostly in Blinker, I'll go for the one with the Stanley name, a reliable brand, instead of looking for a cheap one.
It seems like this is the only place to go for LEDs in Valve in the future.
The light distribution is not the same as that of a light bulb, but it is well thought out, and I did not notice any discomfort in the point light state.
View detail
Meter Bulb
Meter Bulb went out so I replaced it. View detail
Fits: KAWASAKI KSR110, KAWASAKI KSR110, HONDA PRESS CUB 50 DELUXE, HONDA PRESS CUB 50, KAWASAKI KSR110, HONDA SUPER CUB 50, KAWASAKI SUPERSHERPA , KAWASAKI SUPERSHERPA , HONDA SUPER CUB , HONDA SUPER CUB Custom, HONDA SUPER CUB 50 Custom
turn filament
Acquired for HONDA SUPER CUB 50 CUSTOM.
Part number No.86, manufacturer STANLEY.
Excellent lamp, everything came up. STANLEY quality is excellent.
Great lamp, everything came up. The STANLEY quality is excellent. -------------------------------------------------- -------- Acquired for Honda Super Cub 50 Custom. Article of the details No.86, manufacturer Stanley. Great lamp, everything came up. The quality of Stanley is excellent. Great Lamp, EVERYTHING CAME UP. The Stanley Quality is Excellent. Powered by Google Translator
View detail
Use at your own risk for Motorcycle
[How is it used?
TZr250R (3XV) The product was used for the Headlight of the
It is for Vehicle, so it is at my own risk, but I bought it and replaced it because I liked the price and the warm color.
Was the one you received as per Image?
Packaged in inexpensive but solid Package.
Was the installation difficult?
In the case of TZr250R, it can be replaced without any special tools.
It can be replaced in about 5-10 minutes, as it does not require removal and installation of the Cowletc.
How was your experience with it?
It is for use on 4-wheeled vehicles, so if used on a Motorcycle, it is at your own risk.
As I recall, the difference is that they are not very vibration-proof, so their lifespan is a bit shorter or something.
The color of the Lamp itself was exactly as I had imagined.
As for the brightness, I personally feel it is not that bright. Well, I think it is sufficient for the price.
【Review】
The color was as I had imagined, but as for the light intensity, it is there.
Well, it is visible enough even when driving at night, so I think it is doing a good job for the price.
Quantity at this price:2pc. Since it contains a Set, I think it is cosmetic even if its life is a little short.
View detail
PS250 [Color] Used for pre-blinker for clearing
Blinker cover for PS250. [Color] I bought this product because I had to replace the Orange bulbs to make them Clear. I bought this product because I had to replace the Orange bulbs with Orange bulbs to make them Clear. I think it is worth the cost. View detail