Reviews
Tail Bulb replacement for KSR's Fender Eliminator Kit
I purchased a used KSR80, but the previous owner installed a Fender Eliminator Kit, and the tail lamp is a Lucas type.
There was a Trouble with Tail Bulb immediately after purchase.
I removed the Lens to see the model of the Lamp to replace it, but unlike the usual Double Bulb, the head was a Small Rhinoceros Bulb.
This Type was not sold at Home center or Car Shop 。 Maybe MotorcycleParts specialty stores have them, but I can't find any near me. 。
However, because the length of the Tail Bulb was different, it interfered with the Lens, causing the Lens to chip, melt, and consume more power due to its higher wattage.
I had put it off because it was inexpensive but the shipping and other things made it needlessly expensive, but I had some shopping to do at WeBig, so I bought it as a package deal.
After installation, there was no interference (obviously), and since the Watt number was lowered, the power consumption was also lowered, eliminating the concern factor.
I am planning to eventually switch to LEDs, but there is a barrier of full-wave rectification, so I may end up putting it off.
View detail
Normal is fine.
Tail lamps that are always on are consumable.
Stop-lamps are still alive but replaced immediately when noticed to avoid maintenance failure due to trivial things.
We had thought about using LEDs, but we concluded that Standard was the best choice due to its cost performance and reliability.
In the case of DJEBEL, the OEM installed Carrier interferes with the approach of the Tail lamp cover to the Screw. This is where SEA BASS comes in:remove the rear screws from the carrier, loosen the front screws, and stand the carrier up like a Gal wing, and the replacement can be completed in a few minutes.
The durability of the bulbs is a matter of luck, but since it is a product of FOR JAPAN MODEL MANUFACTURER, it is safe to use for the time being.
View detail
Tail lamp replacement for JOG for repair.
Tail lamp bulb of a 2-stroke JOG obtained through a private sale was broken and was replaced.
Lower price than Valve for OEM Parts, Quantity:1 Set of 2pcs.
I will only use 1 pc. and will keep the other one as a spare.
I thought about using LED Tail lamp bulbs, but since it is a 50cc moped, these are sufficient.
*Wattage should be matched to the OEM.
View detail
A very ordinary Halogen bulb.
Whenever I buy a used Motorcycle, I always replace all the valves with new ones, but since they were out of stock at my local store, I couldn't be bothered to come back to the store, so I bought them by mail order.
I thought the price might be a little higher than the actual store. I thought the price might be a little higher than in the actual store, but considering the time and effort involved, it was acceptable.
There is nothing wrong with the fit and there is nothing special to say about the color.
This is fine unless you don't want the Amber color to stand out over the Lens.
I thought it might be a good idea to purchase an additional one as a spare when I purchase some more Parts.
View detail
It is safer to always have it at home with Spare!
The cheap Pine Stripe bulbs, but just one of these can cause a maintenance failure!
They run out without notice, so it's always safer to have one in reserve.
Depending on the model of car, the replacement work is a single +Driver.
View detail
Rare 6V bulb
I used it to repair a broken Neutral lamp on a VANVAN90 that was given to me by a friend's father.
Since it is an old motorcycle, there are no parts available, so the rare 6v bulb is a big help.
View detail
The abundant number of Watt will help.
I added Hazard and bought this one to lower the Watt number in terms of power consumption reduction.
It was really helpful to have Double Bulb as well as Single Bulb.
The abundance of Variation here is very good, as Motorcycle definitely does not look good with flashing LEDs.
View detail
Cost-effective
Used for POSH and Fath blinkers. POSH has Valve, but I bought this one because Mats Stripe products are much cheaper even though they are the same standard. I have used them on other cars and have confirmed that there are no quality problems, so I can use them with confidence. View detail
For Meter Bulb
I purchased this for my 4LMONKEY Meter Bulb.
If you like the old-fashioned way, this is the way to go, as it is not as flashy and bright as LEDs.
View detail
No problem and safe. Just be very careful about the angle and shape of the mouth Gold.
For the Tail lamp, we avoided LEDs so that the power generated would be used properly in combination with the power consumed.
I hear that it is not good to have too much surplus electricity because once electricity is generated, it can only be converted into heat, etc. at the Regulator.
The Headlight is always on and off and I thought it would not be affected by the LED, but the Tail is always on, so I left the White hot bulbs on.
Made by Pine Stripe, no question about it...White heat bulbs are becoming a component that I'm thankful they still manufacture.
We kept one as a spare just in case.
View detail
it is normal
Product Name
M&H Pine Stripe MAnd H Pine Stripe Double Base Bulb S25 BAY15D
Item Number
1P3407C
Vehicles
DREAM110
Number of man-hours
Around 5 minutes
Why did you choose this product?
I bought this as a for repair because my Tail lamp was out.
The reason why I chose it is that it is inexpensive, which is a Large reason.
I decided to use regular bulbs because it was not worth it to replace them so many times when I changed to LEDs.
Impressions after using it
You can definitely use it and it will light up if the Size compatibility with the vehicle is not wrong.
If it does not light up, it is likely that you bought the wrong product or the product Body is defective.
The product I bought worked fine for both the tail light and Brake light, so the vehicle was repaired without any problems.
▼ Attention
Size and Type vary from vehicle to vehicle, so you need to research before you buy.
View detail
Stable M&H.
I have no complaints about the quality and price. View detail
I'm doing my job reasonably well.
I bought this because my stop light bulb was out. Replacement was very easy and only required a Phillips head screwdriver. I have no complaints if it is durable. View detail
Thank you for the quick delivery.
I haven't installed it yet, but I'm happy that it's delivered safely. I'd like to leave anywhere if I could imagine a w800 that would fit well. If the delivery is a little late because the webike is out of stock, the delivery will not be too late! View detail
Reliability Large for a quick fix
I bought it to repair the Tail lamp of the commuter car which had been cut before I knew it. I thought about LED for a moment, but when I think about the reliability of the cost and delivery time, the large thing is that it arrives sooner than anything else and can be fixed quickly.
It's a bit pathetic that if you buy two balls, one is out of stock, but the product is reliable.
View detail
Valuable 6V light bulbs
I am glad that you continue to produce the precious 6V bulbs.
Used for Restore of SportsCUB.
Durability and other factors are unknown as we are about to test it.
The slightly higher price is unavoidable given the production numbers.
By the way, it is not related to the product itself, but one point is noted.
Check the application carefully when buying old Car bulbs.
It's very easy to make mistakes.
View detail
Get up and walk away.
Used with Ninija250SL
I was unlucky enough to break a Blinker bulb when I was standing on it, so I had to replace it.
It was only One Side, but Quantity:Pair (for Left and Right) I didn't particularly care for the difference in color between the two (although it might bother some people...)
View detail
Eggplant-type Valve
Used for Blinker.
It is a slightly fat eggplant shaped Valve. No problems in use.
Around Amazon, Valve which converts Socket to LED is sold as it is, but honestly there is no sense of security at all, so I will continue to use this kind of conservative White heat Filament in the future.
View detail
The anti-vibration spec. is a personal no-no.
It's a Double Bulb, but the poor quality ones run out quickly and are useless.
The Pine Stripe ball is an Image that can last about 10,000km.
Lately, there are some that have 3 legs of Filament, because of the anti-vibration Spec. but for some reason, from experience, that one cuts faster. Why is that? ……
This Valve is a normal Quantity:It's a 2pc foot, so I don't have anything to say about it.
View detail
Overcurrent cuts it off quickly.
I used it on my FZ750 tail lamp.
The product itself is made in Japan with no problems.
The problem is in my FZ, probably due to a weak Regulator, which causes an overcurrent situation when fully open for long periods of time, such as Circuit.
When I did so, there was a high probability that the tail lamp went out.
Again, it's not the product's fault, it's my fault for poor maintenance.
But on the other hand, when I changed the tail lamp to LED, it did not turn off even in this state.
In terms of resistance to external factors, LEDs seem to be the way to go.
After this, another part was broken by the overcurrent.
The cause of the problem has been identified and addressed, and there are no further problems.
Overcurrent is dangerous because of the flames.
View detail