Reviews
Trusted Pine Stripe
[How is it used?
I was looking for a KITACO Durable Lens Mini Blinker Set (https://www.webike.net/sd/372536/) because the ball had snapped.
12V-8W [T-10] He is a very rare character, so I thought, "No way! I was about to lose my temper, but I found this 12V-10W [T-13] I got the information that this product can be substituted with
Was the one you received as per Image?
It arrived in the familiar Pine Stripe's Packaging. It is very secure.
How was your experience with it?
They lit up with no problem.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
The Valve of the Unbreakable lens can be replaced by removing the Lens, but it can also be replaced by pulling out the whole Socket from the back.
Also, some people do not know this, but if you touch the Valve with your bare hands, the sebum from your fingers will adhere to the Valve, which can cause it to heat up easily and shorten its life. 。 Therefore, it is best to wear work gloves or military gloves to protect your hands and fingers.
View detail
Blinker Bulb of a bygone era
Ordinary Blinker Bulb being eclipsed by LEDs View detail
Used to convert 6V vehicles to Clear blinker
[How is it used?
[Color] I changed to ClearEuropean Blinker and needed Orange bulb.
How was your experience with it?
Works fine. Unlike the cheap Orange bulb, the paint was well done.
How did it compare to other products?
I'm afraid you don't have to worry about 6V Orange bulbs because there are very few options.
View detail
Not bright.
Blinker on moped is now LED.
The brightness was dimmer than the bulbs and did not make sense.
However, the power consumption became smaller, so I think it was effective there.
View detail
In the Restore of VANVAN90
I used it to repair a broken tail lamp on a Van Van Van 90 that was given to me by a friend's father.
The 6vBattery can die without your knowledge, and if you run with the Light on without realizing it, you will inevitably run into various bulb breakages.
We are grateful to WeBig for always having 6v bulbs in stock because few stores have them in stock!
View detail
Dazzlingly bright.
I wanted to convert the VMAX Blinker to LED, but I was hesitant because the Blinker relay is a BlinkerControlComputer, so I could not replace the Relay, and the only solution was to put a resistor in the Harness.
I checked, and to my surprise, there was a pontoon Valve.
So, this product is 2Quantity:Buy the set
Measured the valve size and ordered a small one to be installed.
When I tried it on, the Rear could be worn with only a little bit of atamen interfering with the Lens.
The Front was a Double Bulb of the type that lights up in Small. (SmallWiring was killed and I didn't notice.) I'm a bit of a failure.
Skip one of the Bracket bins and install a Single Bulb.
It did light up, so that's good. There is a little interference with the Lens, but so far it is Large sturdy.
The brightness is much brighter than the Normal valve, close to dazzling.
Indicator went bad and became Hazardous, so we used a different product to counteract the problem.
See separate impre...
View detail
The 6v bulb, which is now rare and precious.
The 6V ball, which is now rare and precious, used to be available at Home center, but now it is not sold at all. 。 We keep several types under Seat in case the ball runs out while you are on the road. It is recommended to have a spare. View detail
GORILLA2V Change
Purchased 6VGORILLA for 12V changeover.
It was easier to do than collecting in Rose.
View detail
![Blinker Bulb/Monocyte [12V10W] Orange Light Emitting / 1pcs](https://img.webike-cdn.net/catalogue/14762/07312134_51f904712c027_TS.jpg)
Fits: HONDA ZOOMER(Ruckus), HONDA NSR50, HONDA NSR80, HONDA XR100R (for competition), HONDA XR50R (for competition), HONDA APE 100, HONDA APE 50, HONDA GORILLA, HONDA JOKER90, HONDA JOKER Helmet, HONDA MONKEY
Used for GORILLA
I purchased this product because I changed my 6VGORILLA to 12V and was able to install it without any problems.
I would like to replace them with LED bulbs at some point.
View detail
Fits: SUZUKI GSX-S1000F, KAWASAKI ZRX1200 Daeg, KAWASAKI Ninja 250, YAMAHA MT-09, YAMAHA XSR900, YAMAHA YZF-R25, SUZUKI GSX-S1000, KAWASAKI NINJA250R, YAMAHA YZF-R3, YAMAHA XSR900, YAMAHA YZF-R25, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, YAMAHA MT-09, KAWASAKI ZrX1200ZrX1200 DAEG, YAMAHA YZF-R3, YAMAHA YZF-R3
Good
Used for XForce155 Rear blinker.
Same Valve and Size for NORMAL, so to Lens.
There is no contact. However, the price is too high.
View detail
Fits: HONDA CB400 SUPER FOUR, HONDA CB1300 Super Four
CBX750FBOLDOR Flashing lamp
The blurred flickering of the bulbs became clearer. In addition, the power consumption was reduced in conjunction with Relay. View detail
Fits: HONDA PRESS CUB 50 DELUXE, HONDA PRESS CUB 50, YAMAHA VOX DELUXE Model:JBH-SA31J, YAMAHA VOX
High-cost performance light bulb.
The price is reasonable and it's good to buy a spare. View detail
TZr250R (3XV) Used for Tail lamps in
[How is it used?
TZr250R (3XV) The lamp was used for the Tail lamp of the
I chose this product as a replacement for a vehicle I purchased at an auction because the tail lamp did not originally light up on the vehicle.
Was the one you received as per Image?
I bought it because I was told that it was compatible with OEM Product and I had no problem.
Was the installation difficult?
The Cowl was already removed, so the exchange only took about 30 seconds.
In the case of TZr250R, replacement is easy because the Socket is just twisted and fastened without any special tools.
How was your experience with it?
It seemed slightly darker than the one that came with the original.
It is not difficult to see, and it may be a little darker. It is a Level that cannot be understood without comparison.
The light intensity is sufficient to be visible to following vehicles even at night.
[Included Parts:were they on?
This is the only product as shown in the photo.
[Was there anything that disappointed you?
There is no Level of dissatisfaction with the current situation.
【Review】
Products from a reliable brand that is also used as OEM, and less expensive than OEM parts. (OEM Parts:31L-84714-00 is 352 as of December 2022) So I think it is good.
I ended up only having the Socket side ruined and Valve was still alive, but, well, it is good to have it as a spare.
View detail
Blinker Valve replacement behind PS250
One of the beautification plans for the used PS250 is to change the Blinker from Orange color to [Color] I replaced it with Clear. So I had to replace it with Orange bulb, so I bought this one. This Valve is 23w, so it is for the back.
The old-fashioned Motorcycle seems to have been rejuvenated with a transparent and shiningly feel.
The used PS250 was a First Model Type, so it had square eyes. However, I replaced it with two round eyes like the Second Type Model (I had a hard time because the OEM is no longer available for this one). Especially, the frame of the light is not available. I bought one for ZOOMER for overseas). I painted the body like Second Type Model, so it looks young again at once.
I just wonder why the Valve with the Position lamp for the front is cheaper. This Valve in the back is 23w and I would like to see it sold in the $300 range if possible.
View detail
MONKEY
Blinker became unusable due to a broken bulb while driving on a farm road. View detail
By blinker clear lens-ization of VTR250, since the front was exchanged for the orange ball, an one-piece pack was purchased in reserve.
By blinker clear lens-ization of VTR250, since the front was exchanged for the orange ball, an one-piece pack was purchased in reserve. View detail
By blinker clear lens-ization of VTR250, although exchanged for the orange ball, the thing of an one-piece pack was purchased in reserve in the case of the ball piece of RIA.
By blinker clear lens-ization of VTR250, although exchanged for the orange ball, the thing of an one-piece pack was purchased in reserve in the case of the ball piece of RIA. View detail
Fits: YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X
The orange cover was removed and the bulb here was attached. It becomes a sharp and is very good touch.
The orange cover was removed and the bulb here was attached.
It becomes a sharp and is very good touch.
View detail
Now you're safe.
I did not understand the standard of the Valve of Blinker properly, and when I converted to LED 4 years ago, I was forced to install the G18 Valve. The car passed the inspection, but I felt that the light intensity was not so good.
Recently I became really curious about it and found this in search of S25 Valve, the official standard.
Since the body of the Blinker was the full length of the S25 standard Limit, this product, which emphasizes compactness, is the best match. The light intensity was also sufficient.
View detail
Fits: YAMAHA CYGNUS X SR, YAMAHA CYGNUS X SR, YAMAHA CYGNUS X SR, YAMAHA XSR125
LED conversion of CYGNUS
Only Blinker of CYGNUS was a light bulb, so Relay and Quantity were used to convert it to LED.:I purchased this product from Set.
It was a little Large strange to remove the Cover, but I managed to work with it.
The price is honestly high, but I am satisfied.
I wonder if Hazard and Passing switch are next…
View detail