Reviews
They say it's good if it lasts 5 years.
After five years, it broke. When I removed it, the yellow-colored luminous body was shattered and the base was burnt to brown. The light suddenly faded and became like a miniature light bulb and disappeared. I was surprised because I happened to be watching it. It would have been extremely scary if I had been driving at night.
When I bought it, the yellow colored tip was not square and the corners looked peeled off in places. I asked the ManufacturerStaff if the Large tip was sturdy, but they said it was fine, so I had it installed.
Well, it would be impossible because it looks like the LED light-emitting base part is burnt out.
As for the product review, at 6000k.
It is not brighter than OEM, but the color is White, so some scenes actually look darker. It is still not as good as the most powerful HeadlightHID, but it looks better than the OEM Halogen when compared to rural roads and other places without streetlights. 。
However, in urban, city, suburban, and highway areas where there are some lights, the white LEDs are covered by the lights and it is difficult to tell whether the light is illuminating or not.
If the Type is one light on low and two lights on high, I would recommend changing the color temperature with low high.
This time I did the work myself, but when I first bought it, I was told that it would wait 20,000 hours or 10 years if it didn't break, but in fact it was 5 years, so I felt like I lost money, but that seems to be the way it is.
It is good that they are cheaper now because of the New Model, but I wish they would have stopped reducing the warranty to 2 years if they continue to claim that they can be used for a long time.
Now, how to do the work
This time, I performed the work myself, copying the way SphereLight's ManufacturerStaff actually did it on my Motorcycle.
As mentioned in the postscript, the way this Rubber fits (How to put it out?) If this is the case, the heat sink portion will be buried in the rubber, so I am concerned about whether the heat dissipation will be large enough to withstand the heat.
Turn the round cover of the OEM Headlight unit counterclockwise about 1 cm to remove it.
Remove the valve spring and remove the light valve.
Remove the Attachment from the Valve of the product and insert the removed Attachment into the place where the Headlight Bulb was inserted, with the four notches facing backward, and fasten it with the Spring.
At this point, you should install the Valve once in the Attachment and remember the feeling of pushing and turning it to install.
Attach the supplied CouplerConnector to the product as described in B of the Instruction Manual.
Connectors on the body side and the Light side are connected.
...At this point, conduct a lighting test.
The space inside the Headlight unit is quite large when you put your finger inside, so leave about 15cm of Wiring and put all Connectors and Controllers inside the Unit. (I put almost all of them in Space under Unit)
Note that if the wiring connected to the light is about 10 cm, the light valve will stick when the cover is attached and will not be able to be pierced.
If the controller rattles inside the headlight unit, use the Tie Band to hold the controller in place. I don't do it.
Once this is done, it is time to install the rubber cover, which is the most difficult part.
It takes several hours at worst, and although it is easy to install if the Rubber is heated considerably, it is not recommended because deformation is a concern.
The difficulty level increases because everything is put into the Unit.
Push the outer frame of the Rubber cover into the Unit.
At that time, the side that is folded should be toward the rear of the vehicle.
When you push it in, there are three indentations where the OEM's round cover fits.
Make sure three Folds are outside the Unit, then install the LED Bulb.
(Note that if you push the Rubber as hard as you can, only one Fold will come out backward.)
(The outer frame of the rubber cover of the type after the warranty period of 2 years is larger than that of the type before that, so it should be installed in a larger size.)
LED Bulb is perpendicular to the ground when installed.:Pair (for Left and Right) to be facing the
If the remaining wiring seems long, push it in a little at a time.
The above work was completed without making any cuts.
ManufacturerStaff had done this and it was a work procedure that worked fine.
However, if the rubber is pushed out this far, the heat sink will be buried in the rubber, so I wonder if the heat dissipation is Large sturdy. I wonder,
I had done it this way before, so I copied it as it was.
View detail
Will it pass inspection?
I installed these on a 2016 MT-07. After installation, I had the optical axis adjusted by a Tester shop and they told me that the light intensity is OK but the light has spread to the side, so it will pass inspection 50-50. By the way, before I installed this, I had passed the inspection 3 times with the first generation LED Ribbon from SYGN HOUSE. The brightness is perfect, but since the next car inspection is a year away, I'm not satisfied with the evaluation until then. View detail
Fits: HONDA Dunk, HONDA Sh mode, HONDA Giorno, HONDA BENLY50, HONDA CROSS CUB, HONDA BENLY50110, HONDA DIO110, HONDA glom, HONDA FORZASi, YAMAHA VOX, YAMAHA VOXDELUXE, YAMAHA VOXLIMITED, YAMAHA GEAR, YAMAHA NEWS GEAR, YAMAHA VINO, YAMAHA VINODX, YAMAHA VINOMolar feh, YAMAHA SDR, YAMAHA MAJESTY, YAMAHA MAJESTYC
Low cost Low Bright
To be honest, the brightness is not enough at all. However, if you want a LED light that shines white, this product is a good choice because of its low price and easy installation. If you need brightness for touring, this product is not reliable. It will be difficult to drive at night in places with poor street lighting, especially in bad weather. Especially in bad weather. But it is cheap! Easy installation is excellent. View detail
Yellow color is too strong.
Color is "Color:I was expecting a slightly yellowish color like a light bulb, but when I put it on, it was a bright yellow color.
The product itself is very good.
View detail
LEDColor:Yellow
I replaced my OEM headlight with a Multi-reflector headlight and am using a 6500K LED Bulb, but now that a Yellow Bulb is available, I wanted to see the difference.
Color:Yellow didn't feel as dark as I thought it would.
Note that Motorcycle after 2006 is a violation.
I think it would look great on an old car.
View detail
It is quite dark for a Headlight Bulb.
[How is it used?
Purchased to save power over NORMALHalogen bulb.
Was the one you received as per Image?
The Package was poorly packaged with simple packaging, but the product itself is fine.
Heat sink is solid and not as badly made as I expected.
Was the installation difficult?
Installation is easy, as the valve is simply replaced.
How was your experience with it?
The LEDs are only on one side, so they seem darker than the latest LED bulbs. It is not likely to pass the vehicle inspection, and it is not suitable for a large motorbike.
[Included Parts:were they on?
Nothing is attached.
[Was there anything that disappointed you?
The drawback is that it is dark for low power consumption.
Recommendation for more high Watt bright LED Bulb.
▼The H4Type is sold out, and I feel that this functionality has reached its limits; it is a Headlight Bulb, so it is useless without functionality, so I can't shake the feeling that it has been eliminated as a result of the evolution of more high Watt LED Bulbhe.
View detail
Thin terminals
The high beam has a narrow beam range, which is often the case with LED bulbs, and this one has the same tendency.
However, the connection between the terminal and Coupler is loose, either because the terminal is too thin or the holes are misaligned. After a few months, the Coupler was almost disconnected when I checked it because it flickered. I don't think it is a problem on the coupler side because I have never had such a problem with Philips or KOITO's Halogen.
It may be an individual difference, but if you think the connection is loose, it would be better to fix it.
View detail
It's dark
Halogen is better for this, it is darker. View detail
Fine
Easy on the eyes. The specification states that 2 bulbs will give 3200/3600lumen brightness because one bulb only gives about 1800 lumens, this is very misleading I should have chosen your higher-end product ----- --------------------------------------------------- --- Thuan eyes are easy to see. Specifications specify 2 balls will give 3200/3600lumen brightness because one shadow only gives the brightness of about 1800 lumen, this is very easy to mislead I should choose your more advanced product. Powered by Google Translator View detail
4500K but closer to White
I bought it to replace the OEMH4Halogen, but it is a ClassicCafe racer style.
Too bright for ContinentalGT650 but the color is too White.
I dare you to use 4300K for your car's fog, but if you buy it with the +200K feeling...
It means that it was White. The visibility has increased and the current consumption has decreased.
Good
Too bad the people who choose to buy 4500K are the ones who are looking for a light bulb color.
View detail
Fits: その他 12V car
cheap construction
Very cheaply constructed.
No light when inserted deeply, light when inserted lightly, but wobbly.
Obvious defective product or design error
View detail
I managed to do so, albeit on a tight leash.
SRLucas type7Inch also has
Headlight cover
Depending on the Wiring condition, it will not fit in space.
It is possible. I am a Classic
Because of my supremacy, I chose Halogen's warm colors.
I was also interested in the warm colors of LEDs.
But for some reason, warm colors are not available at any supply store.
It's not on display for a trial…
While the straight white and the middle are on display…
I don't want to pay this Gold amount without checking the actual stone.
I was thinking about it, but I just had the opportunity.
I installed it. if it's 3200k.
It's no match for Halogen, but Limit!
The color was warm, which was a good thing.
I use it as it is.
Is the fit honestly not too much of a strain on Wiring?
A little worried.
View detail
Fits: HONDA CREA SCOOPY, HONDA CREA SCOOPYi, HONDA GIORNO CREA, HONDA SMART DIO, HONDA SMART DIODX, HONDA SMART DIOZ4, HONDA DIO, HONDA DIOZ4, HONDA DIO, HONDA LEAD50, HONDA SPACY100, HONDA LEAD 100, SUZUKI ADDRESSV125S, SUZUKI ADDRESSV125SS, YAMAHA JOGDELUXE, YAMAHA JOG, HONDA DIOSP, HONDA DIO-ZX, HONDA DIOS, HONDA DIOJ
YamahaJOG (AY-01, 2018) Replacement HeadValve
Valve replacement is easy. However, I had to be careful not to break my fingernail when removing the headlight cowl cover−. I think the 4500K color tone is more visible and easier to see in the rain and at night, so I would like to see it added to the lineup. View detail
Wiring is long!
The heat sink is also quite large, so it's a pain to make space for it, but compared to the LEDs of the pontoon type, it brightens up to a level that anyone can see, but if you are replacing the God of thunder 2, you won't feel it that much. The H4Type's AssistHigh beam is very helpful.
Well, the problem is the price... if you're looking for a good price, I'd say God of thunder 2.
Since there is no plating on the body, the valve is fully visible with a multi-reflector, so it looks cheap.
View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
After cutting, I put it in.
I removed 3−4mm from the last conical section to avoid putting it in Original's Light. Glass is still touching, I think 5mm is better.
Socket fits, brighter than OEM, light flickers while idling.
View detail
It's not just the processing of some of the...
To be honest, it was difficult to install; OEM Valve Cover (1 Set of 2pcs.) The "H" was not able to fit in the bag, so I removed it and used it. The description said that it is waterproof, so I just use it as long as I am careful with water from the front cowl rather than water from the rain.
So far it is working fine.
I think the difficulty in adjusting the optical axis and the fact that the lens is not as bright as the Package can be discounted in terms of price.
I also have a spare Halogen, so at worst I can put it back together....
If you are looking for perfection, please make sure to ask a PRO person for help, and if you are thinking of installing it yourself, you should be prepared for a certain amount of forgiveness. The product cosmetically is good.
View detail
Halogen upward compatible
It's like Halogen is converted to LED, so it's very easy to replace the Halogen with LED, but it's not AssistHigh beam or DualHigh beam like the high-end models of other companies, so it gets dark in the front when it's High beam. If you are looking for brightness, I think other products would be better, but I think it's a good cosmetic choice for dress-up in Maine in the city. View detail
Price suitable
It's worth the price
It doesn't feel as bright as 6000k.
I still think it is better to buy a good Large hand
Sufficient for driving in the center of the city.
View detail
Fits: HONDA Dunk, HONDA Sh mode, HONDA Giorno, HONDA BENLY50, HONDA CROSS CUB, HONDA BENLY50110, HONDA DIO110, HONDA glom, HONDA FORZASi, YAMAHA VOX, YAMAHA VOXDELUXE, YAMAHA VOXLIMITED, YAMAHA GEAR, YAMAHA NEWS GEAR, YAMAHA VINO, YAMAHA VINODX, YAMAHA VINOMolar feh, YAMAHA SDR, YAMAHA MAJESTY, YAMAHA MAJESTYC
Wish it was a little brighter.
Reasonable brightness for a moped.
PlusOnHigh beam feels subtle and dark underfoot and in the distance.
Low beam light distribution was good.
View detail
Used for CBR1000RR SC57
Wiring is Limit.
The installation itself is easy.
I was able to find something similar on the web and install it because there was no instruction manual.
I checked it at night, but it illuminates quite a bit in the foreground, so it may not be suitable for driving?
Fashionability is excellent.
I will put it back tomorrow.
A bit of a shame
View detail