Reviews
For handling bare Wiring.
[How is it used?
The 27 year old Serow 225we rear blinker that I use for mountain play has developed exterior damage and poor contact, and I have decided to replace it. Wind for SEROW I purchased a new Blinker that is a crackpot Blinker.
It is common for cheap external blinkers and tail lamps, but there are many products that do not have the wiring integrated (it can't be helped that the wiring terminals are supposed to be processed...). I purchased this product because I wanted to do an OEM-like treatment.
How was your experience with it?
This product is used by cutting the end of the wiring wire through this product to match the length of the wiring wire, but it looks as good as an OEM product.
If we had treated the wiring as bare, we would have been concerned about durability and weather resistance, but this product is convenient in that respect and may have played a role in preventing unexpected trouble with electrical components.
It is also 2m long, so depending on the vehicle, it may be a good value product since it can cover 2 to 3 Wiring.
How did it compare to other products?
I have never used other companies' products of this type, so I can't compare them, but I guess there is not much difference in Large.
It has been in use for about two years, and so far no surface hardening or other deterioration has been observed, probably because it is not constantly exposed to ultraviolet light because it runs inside the exterior.
[Points to note]
There are several different sizes in the lineup, depending on the thickness and number of wires you want to cover. So, please check carefully before you buy.
This is not a type of harness tube that shrinks when heated, so please check it carefully before purchasing.
Other items that would be helpful
The deciding factor in the purchase
[How is it used? This is a duplicate of what I filled out in the column, but when I searched Webike for an OEM-style Wiring process, it was a product that was eligible for Timing Good Sale.
【Included Parts:presence or absence】.
This product is only 2m long and is a very simple package.
[ITEMS TO BUY TOGETHER
Harness tape to stop the border between this product and the wiring, coupler or Bullet Type Terminal to connect the wiring of other brand products to the OEM product, and various types of wiring for when the wiring of the external electrical components is too short, WiringCaulking Tooletc. to install them, you will be able to work smoothly until installation.
Opinions and requests to Manufacturer.
I know this is not a product that will always sell well, but there will always be people who need it, so please keep selling it as long as you can.
View detail
Purchased for Wiring handling
Quantity of electric wire:However, since we used Bullet Type Terminal to extend the wires, it was the right choice (even this product was quite limited when we tried to use Bullet Type Terminal). (When I tried to pass through the Bullet Type Terminal, even this product was quite limiting). The thickness also looks sturdy and good. View detail
Price increased but quality is good
We use it to store cords for bicycles and security cameras as well as motorcycles.
Motorcycle electrical systems can be improved simply by using a harness tube like this one.
Unique to amateur DIY "Messiness." disappears and becomes Stylish.
Also, it's UV and stain protection, so RECOMMENDATION!!!
The unfortunate part is that the price has gone up… even though it's only a few hundred yen, the original price was low.
Pretty disappointed, but the quality is as good as ever, so I'll keep buying!
View detail
Used for Protective Tube of 6V MONKEY/GORILLA Main Harness
Used to play 6V MONKEY/GORILLA Main Harness on GT80. The original Protective Tube had become hardened and chica-chica, so I used it to replace it. After the replacement, the harness became more flexible and I was able to handle the wiring without difficulty. The 1M sales unit is a big help because I could only find other products in 20M or 50M. View detail
DAYTONA Harness tube
[How is it used?
When replacing the blinker, the blinker is replaced with a new one. Wiring was used for protection and waterproofing.
How was your experience with it?
I bought a longer one, so I wondered if it would be too much. I thought it would be a good fit, but it was surprisingly just right.
I think it is supposed to be thermo-compression bonded, but I fixed it with inHemp palmac and harness tube.
How did it compare to other products?
I have not purchased any others, but since they are not expensive and sold by DAYTONA, I think this one will suffice.
View detail
To hide the Wiring around the Handlebar.
Used for Wiring around Handlebar of FXDL1450.
Compared to the OEM Vinyl type, it gives a crisp and custom feel.
You can also choose the length & thickness.
View detail
Required for Homebrew Harness
I use it to finish my homemade Harness.
I use this to protect my Wiring as it is basically a no-no to leave it naked.
I think it could be a bit cheaper.
It's expensive to use a small package.
It is very helpful that they are readily available at supply stores.
View detail
Battle at price
This is the second time I've ordered this product, and I bought it again because it nicely hides the various power cords sticking out from the outside.
Anyway, if you put 1 pc in Garage, it will be useful for something.
View detail
It is easy to use
It is safer to use a double coating for power wirings
I often use it because it is easier to handle than Colgate Tube
φ8 Tubes 1.25sq wire Quantity:The 2pc can easily pass through
Photo from Battery (1.25sqxQuantity):(2pc) I'm going through Wiring
The M6 Hoe Type Terminal can be threaded with it attached
It is just a PVC tube though it is for wiring, and there is no indication about the pressure resistance and heat resistance
It would simply protect the wire from mechanical rubbing, etc
How manyQuantity in the toolbox, as it is ready to use when needed and the 2m is used up quickly:These are the Parts you'll want to set or prepare
View detail
Used for rewiring of old car Just the right size
Because my motorcycle is an old car, Wiring will start to lower the voltage with ageing, so I will pull it out again
I used it, and although this Size is just fine for a Wiring or two, the city MotorcycleParts store
It's very helpful because many of the ones sold at the three stores have thicker ones and the thin ones are not sold
View detail
Wiring is clean
It's used for the Wiring Cover of CYGNUS X, MONKEY's external power supply and outlet
The way to use it is to put it over the cord that was taken out of the power supply by an individual It's not so pretty with the direct exposure to the Handlebar and Meter area etc But by interrupting it in the Slit tube, it's neat and tidy
You can do beautifully even with Heat Shrink Tube, but if you have a coupler or something like that, you can use it I have to remove the tube from the Coupler and install it and then play the Coupler again It's very easy to store with this Slit tube
View detail
cheap
Although I was slightly worried because it was cheap, texture etc.. I think that it is a very good product, unchanged from the Manufacturer object. I do not know whether durability will make a difference, but there is no problem to use normally. View detail
Purchased as a conduit of Hose - - - -
Wiring We purchased instead of a conduit for curing Hose sorting in vacant space in Frame, not for consolidation purpose.
In conclusion it is as expected and satisfactory.
Dare to complain, product features (such as heat resistance etc. ) And I wanted to have Slit no choice in choice.
View detail
I used it for processing Blinker. Inexpensive ◎
I am watching Impre and buying it for Blinker and using it.
Certainly it is exactly right to enter two Exactly.
There was also flexibility and it gathered cleanly.
Akihabara's Sengoku same etc etc. Or rather cheap, so it's recommended..
Rather than being covered much by Sengoku,
(It is natural that it is not specialized in Motorcycle)
Depending on Size NeoFACTORY may be better ^ ^;
View detail
Cheap and convenient for selling out
【What made you decide the purchase?】
It is a place to sell out in meter units, whatever you say DAYTONA etc etc etc. , It is overwhelmingly cheaper compared with other companies.
【How was it actually used?】
It was good that it was almost same as the one used for OEMHarness.
However, since this product has a slight gloss on the Tube itself, if it is used for Ninja 250, since the original Tube is non-glossy, will it just float for a part just changed?
[Others]
Since there is no Manufacturer notation on the Tube itself, I do not know where it was manufactured so that it is for reference.
In the case of automatic for Vehicle, Catalog at Yazaki Denki has a heat-resistant temperature of 100 ° C.
However, PVC (Polychlorinated Vinyl) Since it is 60 degrees to 80 degrees itself, I think that it is good to use it within this range just in case.
View detail
Because it is hard to obtain it unexpectedly, when you buy it together at shopping, ◎
【What made you decide the purchase?】
Cheap price.
【How was it actually used?】
Quality is good and can be used without any problem at all.
【Was it difficult to install? (Hard parts case)】
It is not difficult.. If ordinary code you can enter up to two.
【Please tell me the point of installation and hang (in the case of Hard parts)】
If only the code 2. If you have a Bullet Terminal you can only pass one Bullet Terminal.
It is better to use Oil spray or soapy water when passing the Bullet Terminal.
[Is there anything I was disappointed about?]
There is none.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Large can of measure of (How many items to enter, etc.) And the set sales of 4-6-8 - 10 mm also exist
I think that it is convenient..
【Have you compared items?】
OEM Product, Heat Shrink Tube
[Others]
For Blinker's Wiring. We bought it with Big.
If it is 4 mm on the image, Large body code Quantity : It will be Size for 2pc.
If there is a Bullet Terminal, you can only pass one Limit. The second one is impossible. Honestly code Single Body
It would be better to install Bullet Terminal through.
Although it was cheap, I was worried about quality but it was a fear. It is quite unrepeatable with OEM.
Until now I was deceived by Heat Shrink Tube, but it gets worn out soon and it looks not good as well.
After all the exclusive Tube is usability - It looks very good.
Incidentally before buying just in case in Akihabara same etc. I searched for items, but it is over there
Things were mostly for indoor use, Size and thickness were not good. On a Tube that is likely to be used
It is expensive as it gets. It seems everywhere seems like it seems quite handy.
So, even though I want it, it is hard to get it out of the unexpectedly
I think that you should buy it when you shop.
View detail
Since appearance was also uneasily bad only at a Cable tie although a longer code is bundled, the Tube was purchased to it.It was a Size of the Exactly letting two codes of the thickness of 0.5sq pass. Since it stops passing also by the diffe
Since appearance was also uneasily bad only at a Cable tie although a longer code is bundled, the Tube was purchased to it.It was a Size of the Exactly letting two codes of the thickness of
0.5sq pass.
Since it stops passing also by the difference among merely few Sizes if it becomes this thickness, before purchase, cautions are required.The tube body has sufficient thickness and elasticity to protect a code, and is very easy-to-use.
Since it can purchase per meter, it is dramatically convenient again that only a required part can be obtained.
I thought that it was very appreciated as a Sunday mechanic that such accessories are in a Lineup perfectly although it is a casual Parts.
View detail