Reviews
Female terminal Cover Only
This is a Female terminal Cover Only product. A separate Female or Male terminal (Male terminal Cover) is required.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product requires Cover and Male terminals as it is Female terminal only.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Female terminal is recommended to be used on the + (Plus) side since the connection will be covered when the Cover is attached.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product is Male terminal only, so Cover and Female terminals are required.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Male terminal is best used on the ”-(Minus) side because the connection part is exposed even if a Cover is attached.
View detail
Required for Wiring processing
Required Items for connecting Bullet Type Terminal in Wiring
It's priced right, but I think it's necessary and sufficient.
I think it's better to lubricate it because it's not moving well.
View detail
Finally, it's time to go.
I purchased and installed a Push Type Switch to use as a switch for the power supply of the car navigation system, but the other day, when driving on a mountain pass with somewhat rough pavement, a malfunction occurred due to vibration, causing the power supply to turn off and on, and temporarily Navigation repeatedly started up and stopped functioning.
This symptom did not occur during normal city driving or on well-paved roads, even on mountain passes, so I think that the problem may have been caused by severe vibrations that exceeded the manufacturer's expectations. I think that the previous Push Type Switch may not be good at strong vibrations. I don't want to continue to use the switch in this situation and have navigation problems, so I decided to replace it with a toggle switch that I have and see how it goes.
I bought this toggle switch but never had a chance to use it, so it has been sitting in my inventory for a long time. I haven't tried it in a place where it would vibrate yet, so I don't know how it would work in a similar situation, but I like the way it looks, so I'm glad it works.
It is not waterproof, but since we basically don't ride in the rain and it is installed in a Cowl, it is probably Large sturdy. I have applied waterproof treatment to the terminal part.
View detail
We are running low on inventory.
This is a necessity when playing with Motorcycle and car electrical components. I recently purchased this Bullet Terminal because the stock of Bullet Terminals was running low when I was reviewing the wiring for my Motorcycle's retrofit electrical components.
I don't like to have to stop working when I run out of materials, so I try to stock up on materials that I use frequently, so when I buy Large quantities, I buy these quantities. In this case, I purchased both Male and Female at the same time.
Some of the No Brand products were inferior, but I can buy Emon products with confidence. This time, too, there were no defective products among the 100 items.
View detail
One of these will do the trick!
Used to make Bullet Type Terminal when installing Grip heater on REBEL250.
Was the one you received as per Image?
We chose this product because there are parts for various terminals other than Bullet Type Terminal, and there is no need to purchase additional parts.
As for the pliers, I think they are adequate compared to the more expensive ones, but I think this is fine for first-time users or one-time trial users.
How was your experience with it?
There is a video QR code on the Package for installation instructions, so we worked while watching the video.
I felt that it was the first time or that shimmying was moderately difficult.
[Points to note]
Watch the video a couple of times and do it when you have time.
How did it compare to other products?
Many pliers alone cost about the same price, so I think it is a good deal to have the terminal parts included at a low price.
View detail
I purchased and used it with Male out of necessity.
To be honest, I am at a loss to explain or comment on these parts, but they are working normally.
I am posting this because I think there are quite a few people who Review.
View detail
Just the right product at the right price.
[How is it used?
Used to adjust the length of Blinker's Wiringetc. for Bullet Terminal crimpingetc.
Was the one you received as per Image?
It was just as Image.
The product itself is a little large. I have the impression that it is difficult to use unless you have large hands.
How was your experience with it?
After actually using it, first of all, I feel that the movement is a little bad. I wonder if the problem is that it is brand new, but the opening of the pliers is a bit stiff. This may improve as I use it more.
What was very good about this product was that the Bullet Terminal and terminals were used from the beginning to make a number ofQuantity:Set or attached.
I'm glad I changed to Large because I can buy one of these and get to work right away.
How did it compare to other products?
I used to use a high-end tool from Manufacturer at work, but it was a world of difference compared to that.
However, I think this product is sufficient for Sunday mechanicLevel.
View detail
To add USB power supply
[How is it used?
Used to branch Attachment power to add USBCharger to Motorcycle.
I chose this Splice Terminal because I did not want to change the OEM Coupleretc. as much as possible.
Was the one you received as per Image?
It arrived in a 10-pack as shown in the picture.
No one was crushed or anything, no problems.
How was your experience with it?
Only the OEMHarness coating was peeled off and crimped to the cord for the USB power supply.
The process itself is very easy and not bulky like Bullet Type Terminal.
But I can't put Heat Shrink Tube in the middle of OEMWiring if I use it in the middle of OEMWiring. (You can do this by removing Wiring once from Coupler, though.) Therefore, it was treated with insulated Tape.
[Points to note]
Since the sheathed part is not crimped, it is Large thing to crimp only the core wire firmly.
【Review】
We are happy to be able to put together Refreshing Wiring at a very low cost.
Some people solder wires together, but I think it is easier to work with Splice Terminals because Motorcycle harnesses are hard to work with.
Bullet Type Terminal is also recommended if there is a possibility of adding Wiring later.
View detail
Wiring Connection
Wiring distribution for Bullet Type Terminal, Double Type is required to make the connection and is purchased.
It contains 10 pieces, comes with a Cover, and is a cosmetically pleasing product.
It looks like it is MADE IN CHINA …
Now, the Wiring connection can be made at last.
View detail
Beware of Size Mistakes
[How is it used?
When replacing the blinker of XJR400R, I had to cut off the Bullet Terminal of the blinker to pass the wiring through the blinker bracket, so I needed a new Bullet Terminal.
How was your experience with it?
The Bullet Terminal could not actually be used because it was not the same size as the original Bullet Terminal.
How did it compare to other products?
The Size I wanted to buy was available at Home center for the same price, so this product is not a special bargain.
[Points to note]
The number of pieces was not listed here, but the Quantity:1 Set of 10pcs.
Items to buy together:Electric Works Pliers
View detail
Not bad at all
I was looking forward to get some quality terminals .so I finally found it . thickness of the female terminals are very normal compare to the male terminals .overall product is good this spade terminal connectors are damn good .quality is superb .no need to crimping so hard .highly recommended. value for the money. View detail
Useful to have but the price is Neck.
Because I often use WaterproofConnector to make wiring, I buy this as a spare.
The price is quite high, but it's a Recommendation because it can be used for the Coupler Wiring process of the Waterproof system.
View detail
If you want to branch out, this is it!
Plus Sometimes you want to split the power supply, right?
I think there are a lot of people who use Large bodies, like that red-packing thing
If you can pressure weld them yourself (not hard), you can use this one to branch out, which is handy!
However, if you don't use it, it will be empty and dangerous if Minus touches it
View detail
In the long term
I bought it because I used it for a while..
I think whether the texture is the same as what I am currently using.
For long-term use, Quantity : 1 Set of 100pcs. So, CostPuff performance
Also good.
View detail
A waterproof cover is quite large as other レビュアー are written. The die length is 37 mm with a scalpel, and is no less than 45 mm by a male at the time of 16 mm and union. I think that it is a good product since there is no dissatisfaction in wat
A waterproof cover is quite large as other レビュアー are written.
The
die length is 37 mm with a scalpel, and is no less than 45 mm by a male at the time of 16 mm and union.
I think that it is a good product since there is no dissatisfaction in waterproof performance if the Space of the place to install and the die length of the code to attach are enough.
View detail