Reviews
Large capacity
[How is it used?
Bullet Type Terminals are required for USB power supply and other wiring processes, but of course Bullet Type Terminals are used up.
Quantity:I bought a set of 30pcs. or something like that, but I found that I had no Bullet Type Terminal on hand and had to stop working on it, so I bought Quantity:1 Set of 100pcs.
How was your experience with it?
It is an ordinary Bullet Type Terminal made by Emon, which can be easily obtained at Home center.
100pcsQuantity:Set is not readily available around there, so I purchased it on Webike.
How did it compare to other products?
No specific comparisons were made.
[Points to note]
Sleeve for waterproof is not included, so you need to prepare it separately if necessary.
【Review】
The Large capacity is recommended for those who do a fair amount of DIY Wiring work.
It is better to store them in a 100x box because they may be lost if left in the bag.
View detail
Female terminal Cover Only
This is a Female terminal Cover Only product. A separate Female or Male terminal (Male terminal Cover) is required.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product requires Cover and Male terminals as it is Female terminal only.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Female terminal is recommended to be used on the + (Plus) side since the connection will be covered when the Cover is attached.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product is Male terminal only, so Cover and Female terminals are required.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Male terminal is best used on the ”-(Minus) side because the connection part is exposed even if a Cover is attached.
View detail
Required for Wiring processing
Required Items for connecting Bullet Type Terminal in Wiring
It's priced right, but I think it's necessary and sufficient.
I think it's better to lubricate it because it's not moving well.
View detail
Ideal for Repair
I purchased this product to refresh a MotorcycleParts terminal cover that was given to me by a friend because it was yellowish and deteriorated. I recommend periodic replacement of the cover because many people use the cover for many years without replacing it, causing it to become damaged and short! View detail
Finally, it's time to go.
I purchased and installed a Push Type Switch to use as a switch for the power supply of the car navigation system, but the other day, when driving on a mountain pass with somewhat rough pavement, a malfunction occurred due to vibration, causing the power supply to turn off and on, and temporarily Navigation repeatedly started up and stopped functioning.
This symptom did not occur during normal city driving or on well-paved roads, even on mountain passes, so I think that the problem may have been caused by severe vibrations that exceeded the manufacturer's expectations. I think that the previous Push Type Switch may not be good at strong vibrations. I don't want to continue to use the switch in this situation and have navigation problems, so I decided to replace it with a toggle switch that I have and see how it goes.
I bought this toggle switch but never had a chance to use it, so it has been sitting in my inventory for a long time. I haven't tried it in a place where it would vibrate yet, so I don't know how it would work in a similar situation, but I like the way it looks, so I'm glad it works.
It is not waterproof, but since we basically don't ride in the rain and it is installed in a Cowl, it is probably Large sturdy. I have applied waterproof treatment to the terminal part.
View detail
It's safe to use
We have just purchased Male and Female at the same time, as the stock of Bullet Terminal was running low, in order to review the Wiring of the Motorcycle's retrofit electrical components.
I try to stockpile these frequently-used materials in large quantities because I don't like to be interrupted when I run out of materials during a job.
Some of the No Brand products were shoddy, but I can buy Emon products with confidence. There were no defective products this time either.
View detail
We are running low on inventory.
This is a necessity when playing with Motorcycle and car electrical components. I recently purchased this Bullet Terminal because the stock of Bullet Terminals was running low when I was reviewing the wiring for my Motorcycle's retrofit electrical components.
I don't like to have to stop working when I run out of materials, so I try to stock up on materials that I use frequently, so when I buy Large quantities, I buy these quantities. In this case, I purchased both Male and Female at the same time.
Some of the No Brand products were inferior, but I can buy Emon products with confidence. This time, too, there were no defective products among the 100 items.
View detail
For Wiring processing, this is the one!
[How is it used?
I purchased this Tool set for Wiring process for Blinker and License Plate Light.
Was the one you received as per Image?
I lost my old one so I bought it again and it is almost identical, just like the Image.
How was your experience with it?
I don't know about the Included Parts:I didn't use any of them, but the Electric Works Pliers worked well. The ones I have at home are old Electric Works Pliers and I couldn't get a tight fit, but with this product, I could easily modify them and make them stress-free. I am glad I bought it. I think the cost performance is also very good.
[Points to note]
Nothing in particular. It works fine and I recommend it.
How did it compare to other products?
I compared it to the old Type Electric Works Pliers, but I really liked the fact that it could be clamped tightly and that it was not slow moving. The old type had a different shape for the clamping point, and was hard to open when tightened.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
It's got hair in it, and the claws are straight Type.
There was a hair in the inner bag. It's not food or anything, so I don't mind, but it's a little weird.
The claws of the crimping part (Large type) were straight.
I was expecting Emon to have claws that were rounded inward and easy to crimp. I would have preferred to buy a Rose at the local hardware store.
It's free at the Point, though.
View detail
One of these will do the trick!
Used to make Bullet Type Terminal when installing Grip heater on REBEL250.
Was the one you received as per Image?
We chose this product because there are parts for various terminals other than Bullet Type Terminal, and there is no need to purchase additional parts.
As for the pliers, I think they are adequate compared to the more expensive ones, but I think this is fine for first-time users or one-time trial users.
How was your experience with it?
There is a video QR code on the Package for installation instructions, so we worked while watching the video.
I felt that it was the first time or that shimmying was moderately difficult.
[Points to note]
Watch the video a couple of times and do it when you have time.
How did it compare to other products?
Many pliers alone cost about the same price, so I think it is a good deal to have the terminal parts included at a low price.
View detail
High quality for the price
This high quality can't be beat for the price! Switch on and off with ease.
Recommendation!
View detail
Just the right product at the right price.
[How is it used?
Used to adjust the length of Blinker's Wiringetc. for Bullet Terminal crimpingetc.
Was the one you received as per Image?
It was just as Image.
The product itself is a little large. I have the impression that it is difficult to use unless you have large hands.
How was your experience with it?
After actually using it, first of all, I feel that the movement is a little bad. I wonder if the problem is that it is brand new, but the opening of the pliers is a bit stiff. This may improve as I use it more.
What was very good about this product was that the Bullet Terminal and terminals were used from the beginning to make a number ofQuantity:Set or attached.
I'm glad I changed to Large because I can buy one of these and get to work right away.
How did it compare to other products?
I used to use a high-end tool from Manufacturer at work, but it was a world of difference compared to that.
However, I think this product is sufficient for Sunday mechanicLevel.
View detail
Good product!
Good product!! I recommend this products for beginners motorcycle mechanic and try to DIY, install motorcycle dash cam and USB cellular phone charger! View detail
Now you won't have to buy more.
[How is it used?
I had been modifying and repairing Wiring myself and buying more often, but I decided to buy this product in Large capacity anyway.
For some reason, only the Female side disappears quickly...
Was the one you received as per Image?
It is as shown in the picture. It cannot be sealed, so you need to prepare some other container or something.
I keep mine in a Zip lock for now.
How was your experience with it?
It is a very ordinary Bullet Type Terminal.
However, I feel that Emon's Bullet Terminal Female is basically made tight.
I try to use Pliers to spread out my feelings before using them.
[Points to note]
You must prepare the container in advance! If you don't have one, it will be RoseRose, so please be careful.
There is no waterproof cover, so those who need one must purchase one separately.
【Review】
I'm glad to see that there are 100 pieces in the package at this price.
I have not been able to find it at Home center before, so I am glad I was able to purchase it at Webike this time.
View detail
It won't break.
I used it to attach an additional Switch and it is sturdy without any extra features.
Wiring is simple and easy to handle since the circuit only has a switch function to switch electrical components on and off.
View detail
Highly reliable
I used to buy it in small quantities, but I bought it in bulk because I use it often.
Crimp cleanly and good quality.
View detail
Easy to use
I used to buy it in small quantities, but I bought it in bulk because I use it often.
Crimp cleanly and good quality.
View detail
Easy to use
I used to buy it in small quantities, but I bought it in bulk because I use it often.
Crimp cleanly and good quality.
View detail