Reviews
For Wiring processing
Purchased for Wiring process. No problem. View detail
I like the stuff, but I didn't need it for crf250rally….
Purchased when replacing crf250rallyBlinker
Rear blinkerMinus side connector is not the same shape as the light blue or Orange one, so I thought I could use it on the Plus side,
The Minus side is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
connector set
Quality and texture information is no different from the std product It is compatible with Honda Std products for its usability You should have a wire stripper to buy together It's easy to install Buy based on cost performance and comparative brand preference with other products WeBike packaging is always great, arriving in a week for delivery and packaging Concerns, precautions, or advice on purchase If you connect the cable incorrectly, it is difficult to reunite There should be no failure from the beginning View detail
exchange
The connection connector of the main power supply was old, and its removal and installation was strange.
TAB, receptacle, and Terminal Set, so it is much easier to remove and install with the new replacement.
View detail
Fits: HONDA MONKEY
3-pole coupler connector
Quality and texture information is no different from the std product It is compatible with Honda Std products for its usability You should have a wire stripper to buy together It's easy to install Buy based on cost performance and comparative brand preference with other products WeBike packaging is always great, arriving in a week for delivery and packaging Concerns, precautions, or advice on purchase If you connect the cable incorrectly, it is difficult to reunite There should be no failure from the beginning View detail
Power Supply Branch
I wanted a 110 2-pole terminal for charging and connection.:I wondered if it was a good idea since it is a Set, but substitutions with other inexpensive items would have sufficed. View detail
Replace with new one
The Connector used was old and the claw was broken, so it was replaced with a new one.
Single ItemSince it was sold, it was a great help.
View detail
Power Supply Branch
Used for branching and connecting Power Supply Cable.
Single Item sales were helpful because I could buy only the kind I wanted.
View detail
Branch
Used for branching of Power Supply Cable.
Single ItemThey are sold and the price is not that expensive, so it was very helpful.
View detail
exchange
The Connector we were using was discolored and deteriorated, and was hard to detach and attach, so we replaced it.
It is sold as a Single Item, so I was able to purchase only what I needed.
View detail
It is longer than the one that comes with the Kit.
I used it for my FZ750 Full kit.
I ordered this one because the cord that came with the Kit was very Tight and I had concerns.
The shape of the Connector was exactly the same as the Kit. And the length of the cord is about 20 cm, so there is plenty of room.
If possible, we would have liked the attached cord to be this length.
View detail
Left
We used it for a completely self-satisfying Custom, converting Blinker's Wiring from Bullet Terminal to Connector.
Since it is orange, it is Leftfor Blinker on Honda vehicles. For external Blinker, Wiring is a different color from OEM such as BlackRed or BlackWhite, so it is a Connector color with Quantity:Pair (for Left and Right) It is also advantageous to be able to determine the
Although the Bullet Terminal does not cause any problems, we decided to replace it with the 6V MONKEY/GORILLA Main Harness in conjunction with the re-pulling of the 6V MONKEY/GORILLA Main Harness.
The blinker used is the Unbreakable lensMINI, which has a similar connector, but the shape of the connector is slightly different from that of the product in question, which appears to be a connector for XR100MOTARDetc.
I purchased this product by mistake. but you can pull the Wiring out of the Blinker's Connector and plug it into the product in question.
The only use I can think of is to purchase it for repairs on adapted vehicles, but if you replace the Bullet Terminal, it will make it easier to follow the Wiring. It will be easy to tell at a glance if it is a BlinkerWiring afterwards.
View detail
Replacement from Bullet Terminal
We used it for a completely self-satisfying Custom, converting Blinker's Wiring from Bullet Terminal to Connector.
Although the Bullet Terminal does not cause any problems, we decided to replace it with the 6V MONKEY/GORILLA Main Harness in conjunction with the re-pulling of the 6V MONKEY/GORILLA Main Harness.
The blinker used is the Unbreakable lensMINI, which has a similar connector, but the shape of the connector is slightly different from that of the product in question, which appears to be a connector for XR100MOTARDetc.
I purchased this product by mistake. but you can pull the Wiring out of the Blinker's Connector and plug it into the product in question.
The only use I can think of is to purchase it for repairs on adapted vehicles, but if you replace the Bullet Terminal, it will make it easier to follow the Wiring. It will be easy to tell at a glance if it is a BlinkerWiring afterwards.
View detail
no inconvenience
K-CON, which I will use as well as Emon. when I buy, I am thinking about which one is in stock, but let's thank everyone involved in the Motorcycle industry for doing a good job of selling these products in Small portions. View detail
Replacement and machining of aged Coupler
We decided to replace the 3-pole coupler on the Speedometer side, which had deteriorated significantly over time. In addition, I decided to take out the necessary wiring directly from the coupler to cancel the intermediate harness of the Shift positionIndicator, which was in the way. Since I had just replaced the 6V MONKEY/GORILLA Main Harness the year before last, the Coupler on the body side was in good condition, so all I needed this time was Female. Quantity:I was going to buy the Set stuff, but I found a product that was just the part I needed.
For the replacement work, the wiring of the old Coupler is cut off at the root, and when the terminals are newly installed, the wiring cut off from the middle harness is added to each terminal, and the quantity is changed from one terminal to the other.:I finished by plugging the terminals into the new Coupler so that the 2pc's Wiring comes out. Now I can connect the Shift positionIndicator directly without interrupting the intermediate Harness, and the Wiring of the Front is a bit Refreshing.
The body texture is not bad, so it can be used normally without any problem.
View detail
I bought as many as I needed.
We decided to replace the 9-pole coupler on the Speedometer side, which had deteriorated significantly over time. Since the coupler on the body side was in good condition, only the female coupler was needed this time. Quantity:I thought about buying a Set item, but I found a product for only the part I needed, so I bought this one. I cut off the wiring of the old coupler at the base, installed the terminals I bought at the same time, and inserted the terminals into the new coupler one by one while checking the color of the remaining wires on the old coupler. The texture of the body is not bad, so unless there is an Accident in the future, it will not have to be replaced until the car is scrapped. View detail
Frequent occurrence around Handlebar
I used it for a simple Kill switch Wiring recombination.
It's simple and I didn't have any trouble with it, but it's not suitable for areas where waterproofing is required.
There was also an assortment of products such as the Deutsche Coupler, so you can choose the right one for your location!
View detail
Power supply
It is a purchase as a Connector for the power distribution from the Meter part.
The shop in my neighborhood didn't have 9PType in stock.:Set had the lowest sale price on this product, which is a big help.
View detail
The Same Shape as OEM
I bought this one to use for my Side Stand Can Engine Starter Motor, I was looking for the same color as the OEM but couldn't find it and it looks like they don't have it, so I bought this one with the same shape.
The shape and so on are the same as OEM, so it is not a problem, but Male, Female, Tweezers, but the selling price is reasonable.
View detail
When in doubt, Emon
If you're not sure about buying this kind of thing, choose Emon Industries.
Mostly everything you need is here.
There is also a certain amount of Quantity:It's a set, so it's hard to buy additional items after you've purchased it.
If you're a PRO, it might not be as cosy, but if you're an amateur, it's fine.
It's also easy to stock as is, since it's mostly in Case.
If you need help with connectors, you can find all the parts you need at Emon Industries.
View detail