Reviews
K con cable Tube mark . super quality
I'm looking for genuine quality products.this the one what I need .good quality blabel mark . soft sleeve and sharp marking.highly recommended product.thaks k-con. View detail
K con insulation tube .super quality
Super quality flexible and high durability.this my 2nd order.last year brought one still using without hard and still flexible.highly recommended product.thaks k con. View detail
LED.
It's a must-have when using LEDs. View detail
I'll hold it steady.
I bought this for KITACO and Inner wire and for Cable which was removed.
I think it's good to buy a new cable if it comes off, but my old car is coming out without Parts, especially the separated wire of 2Cycle car, so this product is very helpful.
I purchased the Axel side 6/6Clutch Side 6/10.
The Screw is short and long enough to store securely, so you won't have to modify it after installation.
I haven't used it yet, but I think I'll use Epoxy adhesive to hold it in place when I install it.
It comes with a Hexagonal Wrench, but I don't need it, and I would like the price to be a little lower without the Hexagonal Wrench. (This time, there are now four Hexagonal Wrenches of the same Size.) So it became a Cost performance 4 stars.
View detail
BachaoRelay's companion
I've installed these on every Motorcycle I've ever owned.
This is the standard Relay for use with Bach Direct Relay.
I'm sure you can find as many ways of Wiring as you want if you search for BadDirectRelay.
HDLight (Low beam) If you replace the fuse with a power supply extraction fuse and connect this product, you can complete a direct relay without damaging the harness of the car body.
Because there is also capacity there, it plays an active part Large as Attachment power supply.
By the way, in the case of branching, One-touchConnector of WAGO Japan is small and the connection is easy, and is recommended.
If you search for "WAGO Japan" on Amaz◯n, you can buy the exact same one at the original price.
Both this product and the One-touchConnector above are non-waterproof, so be careful where you install them.
Nowadays, it is almost necessary to install USB power supply and other electrical components, so we are very grateful for the parts that can be used to build a direct relay at a low price like this product.
View detail
Easy to use
[How is it used?
I usually use it for additional Wiring etc., but I bought it again because the one on hand was lost.
Basically I use 0.75sq, but this time it was the WiringRepair of Small TypeMotorcycle which does not use power so much, and addition, so I chose the thin wire 0.5sq here.
[Was the product you received as Image?
Photo
The length is 5m and quite a lot for cheap, so it's enough for Sunday mechanic.
How was your experience with it?
It's just a normal thin wire Wiring Cord.
Even though it is a fine wire, it has a certain diameter, so it is not difficult to crimp.
The good thing about Emon's Wiring Cord is that you can hook up the excess wire on the Holder.
It's nice to be able to keep all the extra lines together, since you basically have to keep them unless you need them.
【Review】
It's inexpensive, easy to use, and convenient for keeping all your Wiring together.
I've always used Emon's Wiring because I've heard that it has no problem with heat and oil resistance.
View detail
Ideal for controlling Blinker current sharing when adding a low-cost Hazard kit.
[How is it used?
When you light a blinker lamp by adding an inexpensive retrofit Hazard Function Blinker relay without changing to the with Hazard Function Blinker relay, you can use 4 of these diodes (2Pack) to control the current sharing when each blinker relay is turned on. I use 4 of these diodes (2Pack).
Was the installation difficult?
Both ends of the wire are cut off, so I used Bullet Terminal crimp terminals this time.
If you don't have a Crimp Tool or terminals, you will need to connect it with a Solderer.
How was your experience with it?
There is no current crossover and they will not fault each other's Relay.
[Included Parts:were they on?
None
You will have to provide all the tools and terminals yourself.
The capacity is 6A, so it can be used in most current paths.
View detail
Fits: HONDA CB1100 F (SC11), HONDA CB1100 R (SC05), HONDA CB1100 R (SC08), HONDA CB750 F (RC04), HONDA CB900 F (SC01), HONDA CB900 F (SC09)
For Wiring
I bought this for the terminals of Wiring.
The cover, the color, is thin, but it is attached, and it is easy to distinguish and can be used in a good way. Package is also decent for the price. It would be nice if there were other Cover colors, too.
View detail
Fits: HONDA CB1100 F (SC11), HONDA CB1100 R (SC05), HONDA CB1100 R (SC08), HONDA CB750 F (RC04), HONDA CB900 F (SC01), HONDA CB900 F (SC09)
For Wiring
I bought this for the terminals of Wiring.
The cover, the color, is thin, but it is attached, and it is easy to distinguish and can be used in a good way. Package is also decent for the price. It would be nice if there were other Cover colors, too.
View detail
A must have Hazard addition to your Handlebar Switch.
I bought this to put the NC700X OEMHandlebar Switch on my Grom JC92.
By using the NC700's Handlebar Switch, the Hazard and Passing functions can be added.
I used the teachings of our predecessors that you have published on the Net as a reference for my Wiring.
Thank you, my predecessors.
The purpose is to prevent backflow into the Hazard circuit when the Blinker is activated.
Quantity:Pair (for Left and Right) Quantity to bite, BlinkerWiring:2pc. Set is required, so Quantity:1 Set of 2pcs.Pack will be very helpful.
The wire is connected by soldering, and the connection part is protected by the expansion tube.
The Diode itself comes with a Protective Tube from the start.
A SORD and Ka SORD are very easy to recognize by the color of Wiring. (It is one way from White to Ash)
Thanks to you, we were able to add the Hazard function to Smooth.
Very satisfied
View detail
You could almost say it's a classic!
I use it as a Relay to turn the 12V on and off with ACC power.
It's working fine.
It's a classic
View detail
For Wiring Processing
I'm sure you can get it anywhere, but I bought it for the free shipping. View detail
For Wiring treatment after Headlight processing.
There are not many Male type terminals, so I bought this one.
It is converted from H4 Coupler to other Wiring as shown in the image.
I think the quality is good.
The video is a night driving SCENE.
View detail
To the Wiring process
I've always been a fan of K-CON, which deals in little things.
The price and quantity are just right, so it helps.
I used this one for Honda on my MONKEY.
View detail
Retro with ease
It's hard to install the Curve because the molding is hard, but it's very effective for motorcycle di-tail up. View detail
watchman
I have been using Emon products for a long time, not only for Relay, but also for Motorcycle. I think the only point to pay attention to is the waterproof measure. View detail
Fits Yamaha Flasher relayCoupler.
The Coupler of Flasher relay of High Flasher relayetc. is 110 type 3 poles.
It is used for high Flasher relayetc. which is not coupler processed, and it is in Couplet-on state.
The molding of the resin is also perfect.
This video is the introduction of my FZr1000. (There is an explanation of Flasher at the end.)
View detail
Items that will make you age 25 years younger!
I remember when I was young (a mystery), I used to run Blinker as a high flasher to make it stand out, and I bought it as soon as I found it.
Webig doesn't seem to have it, but I used Emon's Tri-pole Coupler and installed it.
Normally, the number of blinks is moderately fast, and during inspections, the number of blinks is reduced to within inspection standards.
At first, I thought to put it on the outside of the car body so that it may be easy to turn BodyDial while driving, but because this product is not waterproof, I only put it next to DigitalIgniter under Seat.
* The video is FZr1000 My car introduction
View detail
Separate the burned 2-pole Coupler into 1 pole each!
Is it possible to burn the Coupler of Yamaha, especially DynamoWiring of FZr1000... I divided 2 poles into 1 pole each with this product as shown in the picture.
Now there will be no leakage and no Short.
So far, it has not burned out, even with a single pole Coupler.
Emon is still Emon! (Mystery)
* The video is my car introduction
View detail
You'll want the Ratchet Type Electric Works Pliers
It is recommended to insert Cover before peeling with Pliers. As a result, the problem of which of TAB and receptacle and the problem of injuring a finger by the contents of Wiring occur, but it is not a problem if you work calmly.
If you expect it to bite into the wiring as well, we recommend buying the Ratchet type Electric Works Pliers as well.
View detail