Reviews
Fits: HONDA CB1100 F (SC11), HONDA CB1100 R (SC05), HONDA CB1100 R (SC08), HONDA CB750 F (RC04), HONDA CB900 F (SC01), HONDA CB900 F (SC09)
For Wiring
I bought this for the terminals of Wiring.
The cover, the color, is thin, but it is attached, and it is easy to distinguish and can be used in a good way. Package is also decent for the price. It would be nice if there were other Cover colors, too.
View detail
Fits: HONDA CB1100 F (SC11), HONDA CB1100 R (SC05), HONDA CB1100 R (SC08), HONDA CB750 F (RC04), HONDA CB900 F (SC01), HONDA CB900 F (SC09)
For Wiring
I bought this for the terminals of Wiring.
The cover, the color, is thin, but it is attached, and it is easy to distinguish and can be used in a good way. Package is also decent for the price. It would be nice if there were other Cover colors, too.
View detail
A must have Hazard addition to your Handlebar Switch.
I bought this to put the NC700X OEMHandlebar Switch on my Grom JC92.
By using the NC700's Handlebar Switch, the Hazard and Passing functions can be added.
I used the teachings of our predecessors that you have published on the Net as a reference for my Wiring.
Thank you, my predecessors.
The purpose is to prevent backflow into the Hazard circuit when the Blinker is activated.
Quantity:Pair (for Left and Right) Quantity to bite, BlinkerWiring:2pc. Set is required, so Quantity:1 Set of 2pcs.Pack will be very helpful.
The wire is connected by soldering, and the connection part is protected by the expansion tube.
The Diode itself comes with a Protective Tube from the start.
A SORD and Ka SORD are very easy to recognize by the color of Wiring. (It is one way from White to Ash)
Thanks to you, we were able to add the Hazard function to Smooth.
Very satisfied
View detail
Ideal for securing the Earth of the device to the Bolt of the vehicle.
I use it to hold the Earth of the electronics firmly in place through the Bolt on the car body.
The Stag beetle type would have been fine, but it would have fallen off while removing the Bolt. This perfectly round product is attached to the Bolt properly, so there is no need to worry.
Just be careful because you need to remove the Bolt completely.
Also the Sleeve is properly Quantity:It is safe because it is Set.
View detail
You could almost say it's a classic!
I use it as a Relay to turn the 12V on and off with ACC power.
It's working fine.
It's a classic
View detail
I use it for Wiring protection of power supplies.
The 12V from the Battery is used for Wiring protection from the bottom of the Seat to the Front section.
I think the Colgate Tube is the best choice because the moving part is where it passes to the Handlebar section.
Regardless of the voltage, it is recommended to cover and wire where Short is concerned.
View detail
The size is a little large, but the practicality is perfect.
[How is it used?
ai-net i-Net Waterproof Mini Flat Type Fuse Holder MINI Flat Type is used to protect PL Insurance Products outside the car. The Fuse holder itself is waterproof, but in order to increase the degree of waterproofing, this Wiring Cover is also used together.
Was the one you received as per Image?
It's a little bigger than I thought it would be.
Was the installation difficult?
It's not difficult at all because it's just threading a cable, but it was difficult to find a place to place it because the body is large.
How was your experience with it?
I wrapped it with WaterproofTape because rain enters from the part where I pass the cable.
View detail
For Wiring Processing
I'm sure you can get it anywhere, but I bought it for the free shipping. View detail
Fits: Others For ADDRESS V125LED Blinker and LED Tail Lamp Kit made by KITACO
KITACO Blinker relay for LED
I was trying to keep the wattage as low as possible.
APRIO has Relay under Meter
the reason is that ...
While replacing the Relay, the Front Blinker
LED.
Rear blinker is still there. "Ball."
YamahaOEM Product?
It's a sock.
It makes a chica chica sound.
I think it is a thankful product.
View detail
Fits: Others For ADDRESS V125LED Blinker and LED Tail Lamp Kit made by KITACO
Since the OEM relay is broken.
The OEM relay was broken, so I chose to use the Blinker LED as well. for ADDRESS V125, but I was able to use it on my 2-stroke ADDRESS V100 without any problems. View detail
Plus line concealment
I use it to hide the Red Plus wire of electrical components.
It is recommended for those who are particular about their appearance, as the Black Minus line and the appearance are aligned and become less noticeable.
View detail
Fits: HONDA XR250, HONDA CRM250R, HONDA CRM250AR, KAWASAKI KLX125, HONDA CRM80, HONDA XR230, HONDA CRF230F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA SEROW250, YAMAHA XG250 TRICKER, SUZUKI DR-Z400SM, SUZUKI DR-Z400S, KAWASAKI KSR110, KAWASAKI D-TRACKER-X, KAWASAKI D Tracker, KAWASAKI KLX250, KAWASAKI D Tracker 125, HONDA CRM50, HONDA CRF250M
Please tell me. (_ _) I can't get it to work.
I installed a LEDICRelay made by MOTO LED and the Blinker did not respond.
The other day, when I installed DRC's LED Fender Eliminator Kit, KITACO's Unbreakable lensMini Blinker on the front and rear of KLX250s, High flasher phenomenon occurred on the blinker. I installed the LEDICRelay made by Moto LED, but the Blinker did not come on.
Are there any other necessary parts that I need to install? Please let me know if you have any knowledge about this. (_ _) m
View detail
For Wiring treatment after Headlight processing.
There are not many Male type terminals, so I bought this one.
It is converted from H4 Coupler to other Wiring as shown in the image.
I think the quality is good.
The video is a night driving SCENE.
View detail
For Repair.
Bought for Repair. It is very helpful to have something like this. View detail
It helps in times of need.
It is very useful to have one in your tool box for installation of electrical components, and it is convenient to extend the wiring and free the installation location of the body of the electrical components. View detail
To the Wiring process
I've always been a fan of K-CON, which deals in little things.
The price and quantity are just right, so it helps.
I used this one for Honda on my MONKEY.
View detail
Retro with ease
It's hard to install the Curve because the molding is hard, but it's very effective for motorcycle di-tail up. View detail
watchman
I have been using Emon products for a long time, not only for Relay, but also for Motorcycle. I think the only point to pay attention to is the waterproof measure. View detail
Fits Yamaha Flasher relayCoupler.
The Coupler of Flasher relay of High Flasher relayetc. is 110 type 3 poles.
It is used for high Flasher relayetc. which is not coupler processed, and it is in Couplet-on state.
The molding of the resin is also perfect.
This video is the introduction of my FZr1000. (There is an explanation of Flasher at the end.)
View detail
Items that will make you age 25 years younger!
I remember when I was young (a mystery), I used to run Blinker as a high flasher to make it stand out, and I bought it as soon as I found it.
Webig doesn't seem to have it, but I used Emon's Tri-pole Coupler and installed it.
Normally, the number of blinks is moderately fast, and during inspections, the number of blinks is reduced to within inspection standards.
At first, I thought to put it on the outside of the car body so that it may be easy to turn BodyDial while driving, but because this product is not waterproof, I only put it next to DigitalIgniter under Seat.
* The video is FZr1000 My car introduction
View detail