Reviews
I don't know if it will fit, but I bought it anyway.
I don't know if it will fit, but I bought it anyway. View detail
6V For compatibility with Large type terminals that supply power to MONKEY/GORILLA Main Harness
I bought a battered 900SS (900SL) and am Restore.
The car body was stored in a high humidity environment, so it was also battered by corrosion, but the humidity also entered the inside of the Harness and corroded the core wire in the cord, which was also battered.
Cut the damaged part, create a new Harness, and make a new Connector.
In the end, we had to redo the connector as the center of the connector, because moisture would penetrate and corrode from the area where it is crimped by the terminals in the connector.
When redoing a Connector, play it back in the existing Connector whenever possible.
It's a method of removing corroded terminals from a Connector and replacing only the terminals.
However, if the terminals are corroded, conduction resistance is created and heat is generated, which may cause the ConnectorBody to burn or melt.
Pinch especially Large-type Connectors with Large current flow when they are corroded.
So, this Connector, which is the source of the Large that supplies Battery power to 6V MONKEY/GORILLA Main Harness, was looking a bit iffy, so we replaced it with a new one.
Since it is a standardized product, it is fully interchangeable, and even if it is necessary to replace the harness again for some reason in the future, it can be interchanged without a hitch.
The milk-white Connectors seem to have a tendency to crack over time due to heat and UV rays, but the milk-white OEM Connectors have withstood 30 years without cracking, so I am sure this one will be large and durable.
View detail
The quality is good and can be used without problems!
Active (ACTIVE) I purchased this product for Repair because I damaged the Electro Tap of my company's LEDNumberSIDEBlinker. It works fine and the quality is good! As with all Electro Tap products, it is not waterproof at all, so please use it in a place where it will not be exposed to water! View detail
Used when replacing crf250rallyRear blinker
Used when replacing crf250rallyBlinker
LeftBlinker is Orange.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used for crf250rallyRear blinker
Used when replacing crf250rallyBlinker
RightBlinker is Blue.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Replace from attached terminal
[How is it used?
The terminal attached to GALE SPEED's Clutch holder is Straight Type
It looks ugly as it is (see photo 1), so I was wondering if there is anything better.
I was looking for it and found this!
Was the one you received as per Image?
It was exactly as pictured, nothing different.
Was the installation difficult?
Just pull it out and replace it.
Terminal to terminal connections can be made without problems with crimped pliers and a little bit of skill.
How was your experience with it?
Looks much better (see photo 2).
If you don't care, you won't care.
If you're going to mess with Motorcycle, you want the details to look nice and cool.
The terminals that come with the Parts are perfectly functional, though.
Recomendation because just a little bit of time and effort will improve the appearance of the product.
A terminal is just a terminal, but if a single terminal can change the appearance so much, it is worth replacing it.
[Included Parts:were they on?
None, just terminals and cords.
[Was there anything that disappointed you?
None in particular,
View detail
A friend of old cars?
I'm not sure about current vehicles, but this is a common two-turn Bullet Type Terminal on older vehicles.
I get the impression that there are a lot of them, especially around Tail.
View detail
For additional Wiring
I found an article that the Bullet Type Terminal for Motorcycle is slightly different in size, and it seems that it is not Exactly fitted to A0 products, so I bought one to try it out.
I do think it's harder to pull off than A0.
Why would they change the Size?
And I didn't know there was a difference even among MotorcycleManufacturers.
It's an essential component for safe Wiring processing.
View detail
Older Vehicles on Rubber PartsReplace
[How is it used?
old car (SportsCUB) Used to attach to 6V MONKEY/GORILLA Main Harness at Restore of
Was the one you received as per Image?
Measure the OEM's size in advance and arrange for the closest size.
As a matter of course, I received exactly what was described in Size.
How was your experience with it?
It is a very ordinary ConnectorCover, so it's neither too good nor too bad.
Since different sizes are lineuped, it is nice to be able to choose a close size when replacing parts that are no longer available.
View detail
This is for Bullet Terminal of HondaSmall Type car.
[How is it used?
old car (SportsCUB) Used in Restore of
Was the one you received as per Image?
The Sleeve is also thick and easy to use.
Cheaper ones are usually available, but I would choose this one for its quality of workmanship.
Was the installation difficult?
Electric Works Pliers can be attached if available.
It is no different from a normal Size Bullet Terminal.
[Was there anything that disappointed you?
While not disappointing, it would be better if there was also a Package with a slightly larger quantity and less expensive pricing.
View detail
For repairing faulty wiring View detail
For UniversalMeter installation
In replacing the Meter with KOSO's Multimeter, we did not want to damage the harness on the body side, so we purchased a 110-type 9-pole and 3-pole Coupler and made an intermediate harness so that the new Meter could be detached with the Coupler.
The product was a perfect fit, the terminals were solid, and the product was safe to use. The coupler is compatible with the coupler attached to the harness on the body side of the car without any problem, and it can be attached and detached smoothly.
I think it was a bit of a waste since I only used One Side, but I will keep the extra one in a Large Cutout until I need it some other time.
View detail
Racer vehicle to public road Spec. return
[How is it used?
I purchased the Racer vehicle to restore the Headlight Wiring as it had been cut off.
Quantity as there are two lights in the H4Type Headlight.:2pc. I bought a set
Was the one you received as per Image?
Photo
Was the installation difficult?
Installation can be done quickly if you have a certain degree of Wiring processing skills.
I couldn't work with regular Electric Works Pliers when I was cranking, so I used Radio pliers.
However, The top is for Earth, right? Check the wiring diagram carefully beforehand.
The connector is also securely fastened so that it will not accidentally come loose.
How was your experience with it?
Of course, as long as the Wiring is solid, there is no problem at all in lighting the Headlight.
It also engages well with the Valve of Headlight and does not seem to come loose.
[Included Parts:were they on?
It comes with a Connector and the required number of terminals.
[Was there anything that disappointed you?
Not particularly
【Review】
It is good for those who make their own wiring around the headlight and for repairing old OEMs.
The terminals do not come with spare parts, so install them carefully to avoid mistakes.
View detail
It can be used normally
The female side of the Harness was too stiff, so I used this product to change it. If you tighten it too hard, the cable will break and the connector will become useless, as is the case with other connectors. View detail
Different colors!
Functionally, there is no problem, but the color of the terminal is different between the picture shown on the website and the actual product received!
The photo shows Silver, and the received item is Gold!
I wanted to be inconspicuous and bought it because it was Silver….
View detail
For installation of Grip heater (Crimp available)
Used to install Grip heater.
SUZUKI ADDRESS110, I used it to connect from Attachment power supply to Grip heater power supply.
The only work to be done is to install the Wiring and terminals of the Grip heater into the Coupler using a Crimp to ensure that Plus and Minus are not mistaken, and connect it to the Attachment power supply on the car body side.
I have been using Grip heater for about a month and have been able to use it without any problems.
View detail
emergency measure
Finally, the end-Quantity:The Thailand coil of GB250 CLUBMAN's clutch wire broke and I used it as a first aid kit. The wire was out of order at the point where it was cut, so I used an on-board tool to adjust the tip and cut the end-quantity.:I inserted it into the set and fastened it with the included Hexagonal Wrench. I was surprised that it worked better than I expected, and it is a good thing to have one with you when touring. I learned a lot this time because I can work faster if I have a nipper to adjust the wire. I will add a Nipper to my on-board tools. View detail
K-CON Connector Set
About quality and texture The product is of good quality About the feeling of use I couldn't install it because of the wrong purchase Products to buy together Connector shape female, male. This is the set that you have to buy Difficulty of installation Installation where necessary Cost performance and comparison with other products The price is better than other companies' products and the quality is better About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing When I received the package and looked at the connector, I bought it because it was 3p in the picture on the product page, but it says 2p in the product description I'm afraid I have to use it well View detail
Bullet Terminal for Motorcycle
I searched several mass retailers for a CB103 Honda type Bullet Terminal for my motorcycle, but could not find one, so I searched webike and found it. I searched webike and found it and bought it. Thank you very much for your wide variety of products.
The Bullet Terminal for Motorcycle is small. (I didn't know)
As for the product, it is an ordinary Bullet Terminal and I have no particular impression of it.
View detail
The Emon terminals on hand will not work.
I saw a comment that Emon's plug receptacle was too tight to fit in the Harness plug receptacle, and the product description said it used the Bullet Terminal made by the company, so I had no choice but to buy it.
Naturally, it was installed without irritation.
View detail