Reviews
That's impossible.
Sale item but missing for over a month.Cancelled. View detail
OEM same etc.?
Handlebar side is covered with scratches, even though it is a visible part. View detail
Not for me.
I think it's partly because I'm inexperienced, but no matter how I adjust, the Clutch drag happens.
I spent several hours checking the details, but eventually gave up without a cure.
View detail
not worth discussing at all
Although the total length of the wire itself is the same, the holder installation position (wire adjustment position) is completely different and cannot be installed.
The NC35 is included in the list of compatible vehicles, but it is completely useless.
View detail
Scam!
After placing and paying for my order, I received an email stating that it would take more than a month for delivery. There is a cancellation item in my order history, but I cannot cancel it. They sold me a product that was not available, and it was difficult for me to return the cancellation...
Is this a new kind of fraudulent sales method? I will never buy from here again. Please return the product as soon as possible.
View detail
Fits: HONDA CB400 SUPER BOL DOR (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR Special Edition (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR/CB400 SUPER BOL DOR Special Edition (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR/CB400 SUPER BOL DOR Special Edition (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR/CB400 SUPER BOL DOR Special Edition (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR <ABS> (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR <ABS> (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR <ABS> (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR <ABS> (SUPER BOLDOR), HONDA CB400 SUPER BOL DOR <ABS> (SUPER BOLDOR)
This is not working.
I bought the Cable for my 2010 Super Boldor to replace the Clutch. The difference of the bend angle of the hand side was concerned from the time of installation, but I exchanged it with the thing of the tolerance range. When I replaced it, the Cable holder attached to the Top Bridge was also very bad, and the Adjuster of the Cable was under pressure so that I could not turn it by hand.
I think it is the fault of this Cable because when I went out touring once, I got an objection that the clutch was heavy and the sharpness was bad.
Maybe the poor movement caused problems with the return as well as the pull.
After removing it, it is Garbage box going because the film of the part that hits Holder was torn and the movement of Cable also became reluctant.
View detail
Fits: HARLEY-DAVIDSON TOURINGFamily, HARLEY-DAVIDSON SOFTAILFamily, HARLEY-DAVIDSON DYNAFamily
Quality is not good
I had the replacement done at a specialty Shop and the Lever side Ring shattered upon adjustment! I'm glad I didn't start running it. I guess they didn't inspect it or anything. The return and exchange was also no good. It is better not to use the original without knowing the identity. View detail
Fits: YAMAHA Drag Star (DRUG STAR), YAMAHA Drag Star (DRUG STAR), YAMAHA Drag Star (DRUG STAR), YAMAHA Drag Star (DRUG STAR), YAMAHA Drag Star (DRUG STAR), YAMAHA Drag Star (DRUG STAR)
It doesn't look like the picture
The image shows Stainless Steel
I received the Standard
No explanation.
I don't want to use anything that's marketed this way, no matter how good it is.
It's a shame
View detail
I did a Throttle Wire search and it looks like Clutch Wire was searched
I asked for Throttle Wire and now I get Clutch Wire I don't feel like returning it I don't understand how to contact the manufacturer after I ordered View detail
Incorrect vehicle type
I purchased this product as a compliant product and will review it as a compliant product
Package was also opened and lubricated and I have no intention of returning it
The vehicle models listed on the product page are [SEROW225 Year:95-] It was
The Product Package you received includes [SEROW225 95-96] It was stated that
In fact, the shape of the push rod side seems to be the same as the 4JG2~4 models
My car is a 97 4JG5 so the OEMParts are different in shape
I tried to see if it was possible to use it even if the shape was different, but the gold part that covers the Clutch Wire was It interfered with Carburetor
Even if you angle the Carburetor to avoid it, the Wire will still make direct contact with the Engine
It is necessary to cut or bend the gold coating on the push rod side I'm sure there is, but I don't feel like doing that kind of processing to Clutch Wire because it's too dangerous Mm
I removed each part for installation, but it was a waste of time
Probably, if it is a 95-96 model year vehicle of the SEROW225, I think it is possible to install it It's just for reference
View detail
Fits: KAWASAKI NINJA250R, KAWASAKI NINJA400 (2014-)
It didn't work on the Z400
I bought it because I thought it was the same as the Ninja400, but the inner length is about 1cm shorter than the Z400 I expect HURRICANE to have a LineUp for Z400
It's my own fault for assuming the same thing without permission, but why does Kawasaki bother changing it? It's hard to understand
View detail
Adjustment Adjuster is less than half of OEM
Adjustment Adjuster is not available because the width of the adjuster is only half as wide as it should be
It was not available
In addition, the Manufacturer also reports the current situation from inquiry to the Adjuster's range I inquired about the OEM same or more, but ignored it
ALCAN hands, I'm disappointed in you!
View detail
Less than half of the OEM LengthAdjuster
Bore up for Adjuster, less than half of OEM LengthAdjuster Clutch will not break when used with a reinforced clutch
Loosely, I'm no use to you
View detail
It sucks
I ordered on March 12th and had to wait 2 months for it to arrive Due to Manufacturer shortage Cancelellation, please And the exchange is all one-way emails only, do you guys agree? View detail
It is too cruel.
Originally purchased for using Outer cable only.
Cable's weak point is that the cable surface is rattling, so Clutch lever Touch "Kakkkakakutsu" It will be.
So I decided to make the Inner cable in a single Cable and use only the Teflon coating inside the Outer cable to improve Lever's Touch, but an unexpected incident occurred at the end of the Outer cable.
The diameter of the end of Outer cable is 7 mm shorter than OEM.
OEM 8?.
If there is an error of 1?, Every time Clutch is operated, it gaps and the side of the Lever holder is scraped off. In the long term, the hole of the Holder becomes large and the Lever holder has to be exchanged.
Photo Quantity : 1pc. The eye is an image of the end diameter of KITACO Clutch Cable.
Image on the Holder side inner diameter is measured on the second sheet.
The third piece is an image with Normal cable.
Quantity : 1 Set of 4pcs. Eyes are images containing KITACOCable.
Cable is certainly more resistant to bending if it is more than double, but there is no need for it to be more than double if it is OEM's handling.
Even if Inner is not Stainless Steel, as long as Maintenance is done with Oil, there is no problem at all.
I made something awesome Clutch Cable, but I can not do anything with singing phrases alone.
Mouth "Arorn Boring" It has solidified as it is.
I watched terrible external parts for the first time in a long time.
With this, you can not use it as it is, and Holder will become useless if you use it.
When Wei Big contacts KITACO, KITACO 's answer is "There is no harm in using. It is said that it was an answer. With this there are hurdles too much - - -.
View detail
Fits: KAWASAKI Zephyr 750RS, KAWASAKI Zephyr 750, KAWASAKI Zephyr 750RS, KAWASAKI Zephyr 750
If it restricts to the viewpoint of conformity, it will be below brand-name parts. We cannot recommend you at all. A photograph is in the state which grasped the clutch. A portion without the screw thread at the tip of a mouthpiece is long, an
If it restricts to the viewpoint of conformity, it will be below brand-name parts.
We cannot recommend you at all.
A photograph is in the state which grasped the clutch.
A portion without the screw thread at the tip of a mouthpiece is long, and the dust cover of a rubber becomes narrow touch (it removed).
Moreover, a mouthpiece is long, and Tyco and since it is near, a folding angle will be attached to a wire.
The nylon of the circumference of Tyco has jumped out in the place run about 50 km after exchange.
Details are careless considering the elegance only for a vehicle type.
Since it is not quite satisfactory, it will exchange for brand-name parts.
View detail