Reviews
I used it for Special clutch.
I bought this clutch for my CUB with a special clutch. It is a little expensive, but it is safe. View detail
When using Clutch lever in Mukawa
I purchased a Mukawa Clutch lever, but it was a NORMAL Clutch Cable, so I need this conversion. The price is reasonable. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY RT, HONDA MONKEY BAJA
Good product
It is a bit expensive, but it is used for Takegawa's Clutch, so the fitting is outclassing.
It was replaced while the Clutch was being replaced.
It was not replaced because of any particular defect.
Perhaps due to the generous amount of lubricant sealed in, the movement became Smooth, and I am satisfied with the Large change.
View detail
Fits: HONDA XR100MOTARD, HONDA XR50 MOTARD, HONDA APE 100, HONDA APE 50, HONDA XR50R (for competition), HONDA CRF50F, HONDA GORILLA, HONDA MONKEY, KAWASAKI KLX110L, KAWASAKI KLX110, KAWASAKI KSR110
สายครัช takegawa monkey 50 สำหรับคนที่เปลี่ยนฝาครัชใหม่ สายที่แถมมาจะยาวครับ ตัวนี้พอดีเลยไม่ต้องตัดสายสวย View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY RT, HONDA MONKEY BAJA
Replacement Clutch Cable for the SP Takegawa Clutch Cover on the Grom
About quality and texture: I am happy with the quality of the clutch cable from SP Takegawa, 850mm long cable with rubber boots on the clutch cover end, a stainless steel adjuster, nylon clip on the clutch lever end and a plastic sleeve over half of the cable length. About the feeling of use: I find the little additions like the nylon clip to reduce wear from the lever and the rubber boots to protect the cable from water ingress very helpful in maintaining a well operating cable cable like this one from SP Takegawa. Products to buy together: If you have a missing or damaged rubber boot at the clutch lever that would also be desirable to purchase along side the clutch cabe to minimise water ingress from that end of the clutch cable for a longer service life. Difficulty of installation: The process to install takes about one hour, the right side fairing on the Grom need to be removed to assist in routing the clutch cable. Disconnect both ends from the clutch cover and clutch lever and remove the old cable, then feed the new cable and be sure to avoid sharp bends and possible damage from chaffing and exhaust piping. Finally perform you clutch adjustment. Not difficult to do. Cost performance and comparison with other products: Good costing as you are getting a well designed clutch cable that will last a long time in service but when compared to Honda clutch cable it is price a lot higher. About shipping and packaging: Sea frieght was my perferred method of shipping due to the lower cost but currently unavailable due to Japan Post. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: The 850mm long cable is a good length for the Honda handle bars on the Grom. If you are using a lower handle bar setup then you will want a shorter clutch cable. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY RT, HONDA MONKEY BAJA
Used for Takegawa specula
I had been using the one that came with my Specula Kit for many years and wanted to replace it before it ran out.
I went with a 10 cm shorter one than the Kit one, and it handles nicely and works fine.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY RT, HONDA MONKEY BAJA
Clutch Cable
About quality and texture - Excellent quality, cable adjuster is stainless steel and cable end for the lever has a plastic sleeve for longevity which is nice. About the feeling of use - Nice smooth operation on the pull and easy to adjust. Products to buy together - Would be nice to add the SP Takegawa clutch lever for the finishing touch, product # 02-01-0222. Difficulty of installation - Medium level of difficultly due to the access required for routing the cable. Cost performance and comparison with other products - Good pricing for a clutch cable with some quality items fitted as previously stated compared to OEM. About shipping and packaging - Cheap shipping cost, on time delivery and safety packaged. Any concerns, cautions, or advice when purchasing - This is the 850mm long clutch cable but if your setup requires a different they are also available here on Webike. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY RT, HONDA MONKEY BAJA
Clutch Cable replacement
[How is it used?
Used for 88 GORILLA
Was the one you received as per Image?
high
Was the installation difficult?
unspecialized
How was your experience with it?
My last Clutch Cable lasted me about 10 years, so I'm hoping that I can put Oil in the Cable again to make it last longer.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
It is a little more expensive than OEM Parts.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY RT, HONDA MONKEY BAJA
SpareParts
I used it as Repair Parts for GORILLA's Takegawa Clutch Kit.
The Clutch Cable that came with the Kit was used for about 10 years. I put lubricating oil in it on the way, but it finally snapped in front of my house. It was not in the middle of the road. I replaced it.
It's my habit to put lube in the Cable, so I don't think I need to do it, but I did just in case.
The feeling that I used it is more secure than the Cable that I made by myself, so I think that running becomes easy and I can go touring with peace of mind.
Also, the part number of my Clutch Cable was 22870-KL1-T00, but Uebig confirmed with SP Takegawa that the part number has been changed to 00-02-0133.
PS
Is it just me, or does SP Mukawa Parts seem to be somewhat overpriced? That's why I gave it 4 stars.
View detail
Used with SP Mukawa's Special clutch
Body is CHALY and Engine is MONKEY.
Special clutch by Mukawa Clutch (henceforth Specula) The Clutch Cable Holder attached to the Clutch cover of Speckla buffered the Body of CHALY, so I had to cut the Holder of the Clutch cover.
Then, how to hold the Clutch Cable? But it is this product that solves the trouble.
I used CHALY OEMBody holes to install it.
I don't think there is much demand for it, but it was very helpful that it was there.
View detail
Fits: HONDA XR50R (for competition), HONDA APE 50, HONDA APE 100, KAWASAKI KLX110L, HONDA MONKEY, HONDA GORILLA, HONDA CRF50F, HONDA XR50 MOTARD, HONDA XR100MOTARD, KAWASAKI KSR110, KAWASAKI KLX110
Change to your preferred Length
When attaching dry clutch of Mukawa ___ ___ 0 (800mm) It was too long and Clutch could not run out and exchanged for this product.
Kit attachment here It is a feeling that there is also luxury feeling with Stainless Mesh.
View detail
Fits: HONDA XR100MOTARD, HONDA XR50 MOTARD, HONDA APE 100, HONDA APE 50, HONDA XR50R (for competition), HONDA CRF50F, HONDA GORILLA, HONDA MONKEY, KAWASAKI KLX110L, KAWASAKI KLX110, KAWASAKI KSR110
I used it in Custom
I purchased Cable by changing Clutch of GORILLA to Clutch of Mr. Takekawa this time. Since other Cable classes were Stainless mesh type, Clutch Cable was also set to Stainless mesh type. It looks perfectly! View detail
It becomes necessary for NORMALLever
It is required when you use NORMALLever when exchanging for Mutawa Clutch cover. It is a place to worry about buying a CableAdapter or buying a LeverKIT, but since you need to change RightLever, it became this when thinking about Cost. View detail
Fits: HONDA XR100MOTARD, HONDA XR50 MOTARD, HONDA APE 100, HONDA APE 50, HONDA XR50R (for competition), HONDA CRF50F, HONDA GORILLA, HONDA MONKEY, KAWASAKI KLX110L, KAWASAKI KLX110, KAWASAKI KSR110
Stainless blade ☆ 彡
Three years passed since I changed Engine, so I checked Black Takegawa CableWire. If there is no abnormality, I thought about injecting Grease, but I found a crack, I made it to Stainless bladeWire because the price does not change so much. Since bending R can not be taken so much, choose a long 920 mm.
The new item feels nice, I can worry about it now ~ ヽ (^0^) A
View detail
Fits: HONDA XR100MOTARD, HONDA XR50 MOTARD, HONDA APE 100, HONDA APE 50, HONDA XR50R (for competition), HONDA CRF50F, HONDA GORILLA, HONDA MONKEY, KAWASAKI KLX110L, KAWASAKI KLX110, KAWASAKI KSR110
4mini
I suffered from Length of Cable
Since NORMAL was 920 mm, DAYTONA's
I made 850 mm with Up Handlebar
It seems to be a little longer, so at 720 mm it's short
I made it to this..
View detail
Very well.
I bought it as it is necessary for Normal clutch when installing Magawa's 5th speed mission. I think that it is very good because it is a reliable Manufacturer. I'm planning to install it now.. View detail