Motorcycle Repair Part Reviews

Filter

Write a review and get Webike Points!

Reviews

Standard Type ShortAluminum Billet Lever Set

ARC

17 Apr 2024

Composite Clutch Lever

Fits: HUSQVARNA TC 125, HUSQVARNA TC 250, HUSQVARNA TE125, KTM EXC, KTM EXC-F, KTM SX, KTM SX-F

NO NAME

4/5

Great replacement clutch lever

Best lever on the market,Buy one of these levers,Looks great and functions flawless. you will remember my words when you drop your bike and race because of a broken OEM lever.Durable levers, bike cartwheeled 4-5 times and the levers only had minor scuffs. View detail

R Aluminum Billet Lever Set Foldable Type

LEVEL 10 Racing Power Filter for PCX125/150

Pivot Perch FP/3Finger Clutch lever holder set

ZETA

15 Apr 2024

Pivot Perch FP/3Finger Clutch lever holder set

Fits: Others

Japanese Webike user

5/5

It's crisp and clean.

This is a change from OEM.
The installation can be done without too much difficulty if you have experience in such work as replacing the clutch lever, since there is a translation (please enter hereManual).
Also, while installing it, I felt that the accuracy of the cutting process may vary a bit, and you may be dissatisfied with the Quick Adjuster for Red and Blue. The color will deteriorate under ultraviolet light while in use, and the color will fade, but if you are considering purchasing these as Custom, please be aware of this.
Grease is also applied to the bolt that fixes the lever from the beginning, and the handlebar is fixed with a clamp system, and the screw is very precise, so it was installed comfortably.
The clamp that fixes the handlebar is a little hard plastic material, so there is a possibility that the entire clamp may rotate when it falls over. If you are concerned about it, you may want to change to RubberMaterial.

As for the feel of the operation, as per the Title, it is snappy and sharp.
If you want a direct feel from it, I think you can further modify the Sleeve in the Thailandico fixation area.
Even with the Sleeve position in its normal state, the OEMLever comparison is better, so I felt that the Point is a point of preference depending on how a person uses Clutch.
I wish I had not been stingy and purchased it earlier, as it is one of the other Items that can be fine-tuned for Lever position. View detail

amon

14 Apr 2024

Coupler 2-Pole

Japanese Webike user

5/5

Service Reminder Reset for New Model GSX1300R HAYABUSA

[How is it used?
Recently, many manufacturers have adopted a system in which the Lamp on the Meter lights up when it is time for maintenance.
Various foreign car manufacturers, especially Ducati, are doing this.

But recently, domestic cars are also becoming like that:you have to drop Gold to the Dealer to get rid of the Lamp. Is this part of the Dealer's business strategy? So, even for a simple oil change, if you don't go to the Dealer to have it done, the maintenance Lamp is still glowing all the time.

is Japanese pampas grass, a simple homemade one is all that is needed to solve the problem.

Was the one you received as per Image?
As per Image
It's better to buy it with other things. Since it's only about $100 anyway, the actual store is a better deal when shipping is included.

How was your experience with it?
Effective.

[Points to note]
You have to insert it deep to get it to work.

How did it compare to other products?
Nothing in particular to compare.

Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer

In doing the work, this method is probably a maintenance procedure that is not covered under warranty.
If you want to be stingy with your Gold, please use it only as a reference.

If you are a little worried about the work, you should still buy the OEMReset switch.
OEM reminder Reset switch
09930-83130 Available at Webike, but currently out of stock?

By the way, in most cases, they fail.
It will not respond unless it is inserted firmly and deeply.

Then press and hold the LeftSelectSwitch▼Button to open MENU, select SERVICE, MODESwitch to determine RESET, which is not usually displayed, select Yes when Yes/No appears, and then you can set it individually! View detail

DAYTONA

13 Apr 2024

Golden PadX Brake Pads

Fits: HONDA DIO110, HONDA LEAD125, HONDA PCX150, HONDA PCX, HONDA ZOOMER X, HONDA ZOOMER, HONDA Lead EX

Japanese Webike user

4/5

Highly Control

OEM comparison,
Braking power obviously changes.
Touch on Brake lever is surprisingly Mild.
Wear and tear is a little fast.
Aggressiveness of disc is normal. disc replaced at 60,000 km.

The Red Pad is almost identical to the OEM and ends up being about half as durable as the OEM, so the Golden Pad is better as a result.

Braking power should be the first priority because it is more problematic not to stop at a dangerous SCENE.
If you want to replace it at a store, you will have to pay a labor charge. If you buy a Red Pad, which has only about half the life span of a Golden Pad, because it is cheaper, the resulting two-time labor charge will be the same as for a Golden Pad.

In conclusion, Golden Pad has high braking power and good cost performance. View detail

KITACO

12 Apr 2024

Short Rich Lever Set

Fits: HONDA CL250, HONDA CB250F, HONDA CB250R, HONDA CBR250R, HONDA CB125R, HONDA MONKEY125, HONDA glom

TAEHYEON YU

5/5

I'm writing well.

It's been a while since I bought it, and I thought it was necessary to change it at first, but the more I use it, the more satisfied I am with the dress-up parts. The regular genuine lever was really uncomfortable. It's far from my hand and the lever is thin. It was hard because I kept turning off the bike with the genuine lever, but it's so nice that it's almost gone after changing it. I highly recommend it. View detail

SPHERE LIGHT

11 Apr 2024

LED Headlight for Motorcycle RIZING2 H7

Japanese Webike user

3/5

They say it's good if it lasts 5 years.

After five years, it broke. When I removed it, the yellow-colored luminous body was shattered and the base was burnt to brown. The light suddenly faded and became like a miniature light bulb and disappeared. I was surprised because I happened to be watching it. It would have been extremely scary if I had been driving at night.

When I bought it, the yellow colored tip was not square and the corners looked peeled off in places. I asked the ManufacturerStaff if the Large tip was sturdy, but they said it was fine, so I had it installed.
Well, it would be impossible because it looks like the LED light-emitting base part is burnt out.

As for the product review, at 6000k.
It is not brighter than OEM, but the color is White, so some scenes actually look darker. It is still not as good as the most powerful HeadlightHID, but it looks better than the OEM Halogen when compared to rural roads and other places without streetlights. 。

However, in urban, city, suburban, and highway areas where there are some lights, the white LEDs are covered by the lights and it is difficult to tell whether the light is illuminating or not.
If the Type is one light on low and two lights on high, I would recommend changing the color temperature with low high.

This time I did the work myself, but when I first bought it, I was told that it would wait 20,000 hours or 10 years if it didn't break, but in fact it was 5 years, so I felt like I lost money, but that seems to be the way it is.

It is good that they are cheaper now because of the New Model, but I wish they would have stopped reducing the warranty to 2 years if they continue to claim that they can be used for a long time.

Now, how to do the work
This time, I performed the work myself, copying the way SphereLight's ManufacturerStaff actually did it on my Motorcycle.

As mentioned in the postscript, the way this Rubber fits (How to put it out?) If this is the case, the heat sink portion will be buried in the rubber, so I am concerned about whether the heat dissipation will be large enough to withstand the heat.

Turn the round cover of the OEM Headlight unit counterclockwise about 1 cm to remove it.
Remove the valve spring and remove the light valve.
Remove the Attachment from the Valve of the product and insert the removed Attachment into the place where the Headlight Bulb was inserted, with the four notches facing backward, and fasten it with the Spring.
At this point, you should install the Valve once in the Attachment and remember the feeling of pushing and turning it to install.
Attach the supplied CouplerConnector to the product as described in B of the Instruction Manual.
Connectors on the body side and the Light side are connected.
...At this point, conduct a lighting test.
The space inside the Headlight unit is quite large when you put your finger inside, so leave about 15cm of Wiring and put all Connectors and Controllers inside the Unit. (I put almost all of them in Space under Unit)
Note that if the wiring connected to the light is about 10 cm, the light valve will stick when the cover is attached and will not be able to be pierced.
If the controller rattles inside the headlight unit, use the Tie Band to hold the controller in place. I don't do it.
Once this is done, it is time to install the rubber cover, which is the most difficult part.
It takes several hours at worst, and although it is easy to install if the Rubber is heated considerably, it is not recommended because deformation is a concern.
The difficulty level increases because everything is put into the Unit.
Push the outer frame of the Rubber cover into the Unit.
At that time, the side that is folded should be toward the rear of the vehicle.
When you push it in, there are three indentations where the OEM's round cover fits.
Make sure three Folds are outside the Unit, then install the LED Bulb.
(Note that if you push the Rubber as hard as you can, only one Fold will come out backward.)
(The outer frame of the rubber cover of the type after the warranty period of 2 years is larger than that of the type before that, so it should be installed in a larger size.)
LED Bulb is perpendicular to the ground when installed.:Pair (for Left and Right) to be facing the
If the remaining wiring seems long, push it in a little at a time.

The above work was completed without making any cuts.
ManufacturerStaff had done this and it was a work procedure that worked fine.

However, if the rubber is pushed out this far, the heat sink will be buried in the rubber, so I wonder if the heat dissipation is Large sturdy. I wonder,
I had done it this way before, so I copied it as it was. View detail

KITACO

11 Apr 2024

Exhaust Gasket

Fits: SUZUKI GSX-R1000R, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI katana, SUZUKI GSX1300R HAYABUSA

Japanese Webike user

5/5

Used to replace Exhaust System

[How is it used?
I bought it along with replacing the Exhaust System on my Motorcycle.
I just took delivery of my car and thought I should be able to reuse the Gasket, but this product is so inexpensive that replacing it with a new one is not a Large expense, and I can drive the car with peace of mind from now on.

When the OEM exhaust pipe is removed, the old Gasket inside is taken out, and it is in a surprisingly reusable condition.

Was the one you received as per Image?
As per Image
If you go to 2 Rinkan, Knapps, etc., this Gasket from KITACO is so well sold that you can definitely find it in line.
It definitely looks like something I've seen somewhere else, and I'm not sure if it's an exaggeration to say it's the only option lol.
The Gasket itself is the same as the OEM color, and the size is also Exactly!

Was the installation difficult?
It is not difficult to just put in the Gasket, but to put it in, it may take some time and effort, because in the case of GSX1300RA HAYABUSA, the Radiator and Oil cooler must be shifted in order for the exhaust pipe to drop perfectly.

If the exhaust pipe is removed, this Gasket can be easily inserted.

How was your experience with it?
The Size and color are exactly the same as OEM, so as you would expect from KITACO, a reliable company.
Insert the Gasket, attach the Exhaust pipe and tighten with Bolt.
When tightened, the Gasket is pushed in firmly.

After that, hit the specified Torque and you're done.

[Included Parts:were they on?
No, sir.
Only 4 Gasket

[Was there anything that disappointed you?
I don't think so.

Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer

GSX1300R HAYABUSA2023MODEL, Torque:23Nm*8pcs tightened on exhaust pipe
Despite the perception that the Gasket needs to be replaced along with the Exhaust pipe replacement, I think it is totally possible to remove the Exhaust pipe twice and replace the Gasket once! View detail