Reviews
Fits: HONDA GB250 CLUBMAN, HONDA MVX250F
The texture and shape is so nice that you can hold the Lever all the time!
The adjustment range is quite large, which is convenient, and the large 1-Click angle makes it easy to see the effect. However, the furthest away is too far away to grip, and recently it is too close to full break or full clutch cut.
The color is very nice, I chose Titaniumium color for both Lever and Adjuster, and it matches the traditional atmosphere of GB250 CLUBMAN EXACTLY. I could have chosen a gorgeous color for the Adjuster with Accent, but I think it would have floated around the Handlebar of GB250 CLUBMAN, so I am glad that I chose the same color.
Once, Side Stand didn't go down to the end and I tipped it over, but thanks to Foldable, the lever didn't break! (Lol)
I am satisfied with the WW because the reversible function worked perfectly.
View detail
I put it on as a spare.
External Fuel filter attached to ESTRELLA.
It has been immobile for a while, and you can often find a little bit of age-related deterioration in various parts of the car. 。
There does not appear to be any fuel seepage, especially in the Fuel Cock area, but there is no denying that the Fuel Cock has deteriorated over time.
The other day, I was worried about the rust in the fuel tank, and although I have removed rust to prevent impurities from entering Gasoline, I am not sure about it, so I will install an additional external type of fuel filter.
Fuel filter
A filter device used in automobiles to filter fine impurities contained in fuel.
It is used for the purpose of removing water, sand, and dust mixed in during refueling, etc., and maintaining sufficient fuel efficiency.
There seems to be a time for replacement, though not up to the air filter.
■ 50,000 km at Carburetor Vehicles
■Injection car with 100,000 km
■Diesel car with 50,000 km
is the standard.
Continued use of the filter past its replacement time will not only clog the fuel filter element and cause a lack of engine output, but will also cause the filter to lose its original function of capturing foreign matter and separating moisture.
[When the fuel filter clogs.
‥
Idling of ▲Engine is unstable.
Engine seems to stop when driving.
▲ Suddenly, Engine stopped spewing.
Failure to start = Engine will not start.
I haven't experienced the clogging of the Filter yet, but considering the distance and age, it should be replaced. 。
In my 90's ESTRELLA, the fuel filter is integrated with the fuel cock and inserted into the tank. That is not so bad, but I wanted to be sure.
I also added an external Type as a spare.
I chose KIJIMA's because it was inexpensive and I had used it before.
The deciding factor was the transparency, which makes it easy to see dirt.
Replacement procedure.
(1) Fuel Cock is turned off
↓
(2) To be sure, Gasoline in the carburetor should also be removed.
↓
(3) Interrupt the fuel filter between the rubber hose connecting the fuel cock and the carburetor.
It is wise to prepare Oil Resistant Hose separately because OEM Hose is not long enough.
↓
(4) Turn on Cook and apply Engine.
Operation check.
Fuel Cock flows by Engine pressure.
after replacement
No problems
They seem to be getting rid of the impurities for sure.
Durability...? I think Large is durable because it is inexpensive and will be replaced with a con stunt.
It is a good idea to have insurance on older Motorcycles.
Installation is also easy.
View detail
Used for MC19 CBR250R
Same standard as OEM, so no problems with installation or performance. View detail
I am satisfied with the limited
I am grateful to still be able to purchase this product as it is an older Motorcycle and parts are limited. View detail
Attached to Glass Lens with Cut
I put it on my old CIBIE CutGlass Lens, which is 4500K, but it is not too white, which is good. I heard that cheap lenses may scatter light because they are old, but this was not the case, and it became brighter anyway. View detail
Explosive light, but not compatible with Off-roadFender
H4 Valve replacement Type, so replacement is easy.
Valve size is the same as Halogen bulbs, so there is no need to worry about replacement work.
After installation, the impression is bright! Super bright! It's super bright!
It also reduces power consumption, which is essential for TRAIL vehicles that turn the Cell many times on forest roads.
It may be due to the brightness, but it seems as if the light is diffusely reflected upward by the Fender.
I think it may be due to the Decal, but there is more light in the upward direction, which cannot be managed by optical axis adjustment.
Not enough to adversely affect oncoming traffic, but enough to require a little care in making adjustments after installation.
View detail
Ideal for Wiring processing of homemade Parts!
I used it for the Wiring process of my own ShiftIndicator, and I strongly RECOMMEND using Protective Tubes like this one, as Wiring looks and durability sucks when left bare! I'm glad I bought it because it has withstood rain and UV rays for almost a year and is very durable! View detail
Fits: DUCATI HYPERMOTARD939, DUCATI SCRAMBLER ICON, DUCATI SCRAMBLER CAFE RACER, DUCATI SCRAMBLER CLASSIC, DUCATI SCRAMBLER DESERT SLED, DUCATI SCRAMBLER FLAT TRACK PRO, DUCATI SCRAMBLER FULL THROTTLE, DUCATI SCRAMBLER Limited Edition/Italia Independent, DUCATI SCRAMBLER MACH2.0, DUCATI SCRAMBLER STREET CLASSIC, DUCATI SCRAMBLER URBAN ENDURO, DUCATI 899Panigale, DUCATI 959Panigale, DUCATI HYPERMOTARD SP, DUCATI HYPERMOTARD821, DUCATI Multistrada 1200, BMW R1200RS, BMW R1200R, BMW R nineT, BMW R1200GS
To bremboM4.32.
If there is a fit from Endless, this is the one to choose.
CircuitUser has also been very well received.
Z900RE SE for brembo M4.32
View detail
Good flashing
Very nice flashing lights. View detail
The product was exactly what I expected.
This is the third time I've bought U-KANAYA's Lever,
I decided to use a short type for the first time because the car to which it is attached is a Grom (JC92) and it is small in size.
The look was quite Refreshing and the feel of the operation was perfectly fine with three fingers.
The quality was satisfactory, as I had already experienced with the previous two times, so I was satisfied with the quality I expected, although there were no surprises.
View detail
Bar handle has
I used to use 10cm Long on my HURRICANE Pipe Handlebar Kit, but it was too long, so I decided to use 5cm.
Clearance is just fine.
View detail
Fits: HONDA VFR750, HONDA CB1000, HONDA VTR1000SP, HONDA CB1300SF, HONDA CBR1100XX SUPERBLACKBIRD, HONDA CBR1000RR FIRE BLADE, HONDA CBR1000, HONDA VTR1000F FIRESTORM, HONDA VFR800, HONDA CB1300SB [SUPER BOL D'OR]
Clutch operation is easy!
My Left hand, which was always bad on the way home from touring, does not hurt at all!
The grip was a little jerky with the OEM, but after changing it, the grip felt nur-nur.
Recommendation:Silicon grease and OEM Boots should be purchased separately when installing.
MASTER Boots are likely to be shredded unless they are O/H, so …. (Mine was shredded…) 。
If you are wondering about brembo's MASTER, I think one way is to try this first and see how it goes.
View detail
For Meter Bulb in 6V vehicles
When I went out shopping at night with my Yamaha CHAPPY that I had restored, I could not see the Meter at all and thought it was out of bulbs, so I immediately purchased one.
YamahaOEM Parts are still available, but at a slightly higher price.
I looked up 6V3W and found this product, and since it was inexpensive and in stock, I snapped it up.
10mm BoltQuantity fixing Meter:Remove the 2pcs and the meter cable to access the wiring.
I replaced it and put it back together, and when I started the Engine, the Meter Bulb came on successfully.
Since it is 6V, it is naturally dark, and to be frank, you can only vaguely see the position of the needle when driving at night.
I don't plan to go far, so I'm satisfied that I can see for now.
View detail
Looks good. Fit nicely.
Compared to the old hose, this is much more flexible. Fitment is good, don't think there will be any issue. I can recommend this hose for replacement need. View detail
Sufficient braking power even at low cost
Purchased Repeat for PCX150KF30 Stock.
The first time (approx. 18,000 km) I replaced the Golden Pad by Company D. The second time (approx. 32,000 km) I replaced it with this one because of the price, and I am satisfied with the braking power and control.
I don't do any Sports driving with my PCX150 and feel it is sufficient as it is a consumable item.
The photo shows the current condition after about 4,000 km of driving after replacement, and there is plenty of Pad left.
It is enough if it lasts 10,000 to 15,000 km, so it would be helpful if the replacement is inexpensive for this level of cycles.
View detail
จัดส่งรวดเร็วการแพ็คสินค้ามาดีมาก สินค้ามาถูกต้อง ไม่ผิดออเดอร์ ออเดอร์อะไรไป จัดส่งได้ตามที่ต้องการ และรวดเร็วอีกต่างหาก View detail
Fits: HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA Monkey Baja, HONDA MONKEY RT, HONDA MONKEY R, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MOTRA, HONDA MAGNA50, HONDA MAGNA50, HONDA CL50, HONDA BENLY50CD50, HONDA BENLY50CB90, HONDA BENLY90 S, HONDA BENLY50S, HONDA CUB PRESS, HONDA CUB PRESS, HONDA CUB PRESS
Genuine Kitaco Exhaust Gaskets for SUPER CUB 50
These gaskets were purchase due to needing an exhaust change on the Super Cub 50 and I do not like reusing the old ones if at all possible. These Kitaco ones were reviewed well and so I decided to give these a try myself. The price for the gaskets was excellent and far better than buying the OEM ones which essentially do the same job anyway. I have used a few Kitaco parts before and they really are great quality. I did have some other parts in an order and everything arrived in 5 days from being shipped. The gaskets arrived in the Kiataco packaging and were spot on. No issues or problems and the specs were perfect too. Very pleased with this purchase. View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA MT-25
Made by Active
[How is it used?
I was looking for a decent lever because I was worried about the rattle of the Chinese lever that had been attached to my Yamaha MT-25 from the time it was delivered, and I was worried when operating the clutch.
OEM or KIJIMA products would have been fine, but I had a desire to customize it a bit, so I chose this product from the trusted ActiveBrand.
Was the one you received as per Image?
I purchased the Black color and it was exactly as pictured.
Was the installation difficult?
Since the clutch lever only needs to be replaced, it can be done in about 10 minutes with ordinary tools.
MT-25 (YZF-R25 also) requires OEM colors and washers, so confirmation is needed if changing from non-OEM.
If the OEM color is not available, it costs about 800 yen, which is high-end for just a color.
How was your experience with it?
As expected from Active, there is virtually no rattling.
I am satisfied with R's finish and the QUALITY of the product.
The play adjustment of the Clutch Wire is also infinitely adjustable, but the length of the Bolt is a bit short. (No problem in actual use in my case)
Also, the meat removal to reduce aerodynamic drag ish cool. I definitely don't feel like I can feel the impact at 250cc speeds, though! (Lol)
[Included Parts:were they on?
LeverBody only.
[Was there anything that disappointed you?
Nothing in particular!
【Review】
There is almost no rattle and the product looks good, so it is definitely better to use this one than to buy a strange Chinese Lever.
Brake levers are about twice as expensive due to their complex shape, so the Quantity:Pair (for Left and Right) If you want to have it all in one place, it will be a bit expensive.
View detail
tw200
The appearance has been improved by the Large change,
The instruction manual was easy to understand and I had no trouble installing it.
View detail
Fanless LED
This LED is perfect for vehicles without the space behind the headlight, which is unique to off-road vehicles.
Almost the same size as OEMHalogen, so it can be installed without any problems.
View detail