Reviews
Fits: HONDA CB223S, HONDA CB400SS, HONDA FTR223, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, KAWASAKI 250TR, KAWASAKI W400, KAWASAKI W650, KAWASAKI ESTRELLA, SUZUKI ST250, SUZUKI ST250 E Type, SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI VOLTY, SUZUKI VOLTY, YAMAHA DRAGSTAR250, YAMAHA SR400, YAMAHA SR500, HONDA REBELUp half-wheel* with AMALThrottle
Changed from a bifurcated Wire type for independent Carburetor
I bought a battered 900SS (900SL) and am Restore.
The FCR Carburetor Body is used for the carburetor, but it is not a two-cylinder one, which is often used in car-specific kits, but independent for the front and rear cylinders.
(Independent Carburetor is designated because the radical Camshaft has teamed up with)
For Independent Carburetor, generally comes with a Car Model Kit Throttle Wire branched in the middle." is commonly used.
It is normal to have two branches and four wire ends because they are used for the open and closed sides, respectively.
That's how I used to do it.
To be precise, the Reverse Side was removed because of the poor Throttle Fee Ring, and only the Open Side was used by maintaining the smoothness with frequent maintenance.
The fee ring has been improved considerably since it is only on the open side, but there is still a branch joint in the middle of the ring, and it lacks directness.
To overcome this, we prepared this Wire to pull each Carburetor to Direct.
Wire itself is quite normal, nothing special to say.
If anything, the middle Joint is Material:I'm glad it's Stainless Steel, because I don't have to worry about Rust.
However, there is a bad part, the molding shape of Thailand is a little rough...
Of course, it is not unusable, and there is nothing wrong with using it as it is, but it is not a problem to use the bean-jam-filled wafers. (Monaka) I am concerned about the raised areas of the mesh that were formed by the matching process.
Since the thailand part may rotate slightly at the beginning of opening or just before full opening, the round thailand part will improve the fee ring at the very small opening angle.
I used File to round it out before I used it.
Even if the fee rings are not affected, the thailand coils without any snagging are easier to maintain.
Also, there is no coated tube inside the Outer tube.
It is a Wire configuration with no features whatsoever, consisting of Spiral Tubes made of the old-fashioned Gold genus.
So the first lubrication is a Large thing.
Without oil, the feel will be rough, and with high viscosity oil, it will be sluggish.
On an FCR Carburetor Body with the Reverse Side removed like mine, it is fatal and life-threatening not to be able to spackle back.
This is not limited to this Wire, but try it often before lubricating with the best Oil.
View detail
Fits: YAMAHA V-MAX 1200, YAMAHA SR400, YAMAHA SR500, YAMAHA XT500, YAMAHA YB-1
Gasket-like… of carburetor's Manifold.
I thought I ordered Exhaust pipe Gasket but I received something different….
I think this is Gasket on the carburetor side…?
I can't even return it, which sucks.
View detail
crimping
This is used for re-crimping due to Cable disconnection from the terminal construction part.
Single Item sales, not too expensive, so it is good for purchasing only the quantity you need.
View detail
Construction
Wiring is missing and used for re-installation.
Single Item sales are inexpensive, so you can buy only the quantity you need.
View detail
exchange
Since there was discoloration and deterioration of the used products as the terminals were reconnected, the Cover was also replaced with a new one while it was being used.
Since it is a Single Item sale, it is good for purchasing only the quantity you need.
View detail
Cover
When the terminals were re-installed due to wire breakage, the cover was deteriorated and discolored, so it was replaced with a new one together with the new cover.
Single Item sales and reasonable prices are good for those who want to purchase only the number of items they need.
View detail
Replace with new one
The Connector used was old and the claw was broken, so it was replaced with a new one.
Single ItemSince it was sold, it was a great help.
View detail
Power Supply Branch
Used for branching and connecting Power Supply Cable.
Single Item sales were helpful because I could buy only the kind I wanted.
View detail
Branch
Used for branching of Power Supply Cable.
Single ItemThey are sold and the price is not that expensive, so it was very helpful.
View detail
exchange
The Connector we were using was discolored and deteriorated, and was hard to detach and attach, so we replaced it.
It is sold as a Single Item, so I was able to purchase only what I needed.
View detail
exchange
The Connector we were using was discolored and deteriorated, and was hard to detach and attach, so we replaced it.
It is sold as a Single Item, so I was able to purchase only what I needed.
View detail
very satisfied
There was a situation where the clutch cable suddenly broke, so I ordered it in a hurry, and the delivery was really fast.
The product is also very satisfactory. If you need a longer extension clutch cable by lifting the handlebars up, you can purchase it.
You will use it very satisfactorily. I am very satisfied with the speed of delivery of the product and the build quality of the product ----------------------------------- ----------------------- Suddenly, the clutch cable was cut off and I ordered it in a hurry, but the delivery is really fast. The product is also very satisfactory. If you need to buy a longer an extension clutch cable with a handlebar, you can buy it. You will use it very satisfactorily. Powered by Google Translator
View detail
I appreciate the low price, high quality, and the fact that I can buy from 1pc.!
[How is it used?
I purchased the Bullet Type Terminal when I needed to replace the Blinker on my old car, Yong FourType.
Was the one you received as per Image?
It was more solid than Image. It is totally different from the one from a hundred-odd different places.
Was the installation difficult?
With Electric Works Pliers, crimping is easy.
How was your experience with it?
So far, the contact is energized and usable without any defects at all.
[Included Parts:were they on?
Nothing.
[Was there anything that disappointed you?
Not particularly
I'm glad I bought it because it's the perfect size. I think it's good to buy it as an adjustment when you are almost to the Gold amount for free shipping.
View detail
Processed to VM38.
I bought this for a YamahaXV750E with two VM38Carburetors.
Quantity since it is a 2-stack:I bought 2pc
I once bought a 2-sided Cable for another car model, but it was not long enough and the Piece of the 2-sided part was not enough φ38Carburetor could not be opened.
The VMcarburetor is a type that directly pulls up the throttle valve, so the wire stopper is a traditional gourd shape.
There are some available, such as for SUPER CUB, but I was concerned because the lengths do not match and they seem to be very poor.
Surprisingly, I could not find one for Large size vehicles, and after much searching, I found that GOODS sells one for SR400 and purchased it.
They said it was forφ38Carburetor, but it is only for AMAL364TypeThrottle holder, so it needed Outer processing.
In my case, I have a two-stack, so Tommaselli's Quantity:2pc pull Throttle is used.
It is a pull×2Type instead of a pull/reverse, which is a bit unusual in modern times.
The Inner cable was not long enough at all, so we cut the Outer by 7cm.
The Crimp in the end section was also ported.
Thailandco used Active's products, but since Screw alone seemed to fall out, Solder was poured to fix it in place.
I was able to install it successfully, and since it can be adjusted in the middle of Cable, it can be tuned out.
View detail
The cheap buy.
I bought two and both ran out after about a month.
The tail light is 6W and the wire is thinner than the domestic 5W one, so I wondered if it was Large sturdy. I thought so, but it was not Large sturdy.
I still prefer to use lights made by a proper manufacturer.
View detail
Required for OEMHarness processing
OEM6V MONKEY/GORILLA Main Harness was used as a coupler when it was processed.
The ease of use is OEM Equivalent Product.
View detail
Fits: YAMAHA V-MAX 1200, YAMAHA SR400, YAMAHA SR500, YAMAHA XT500, YAMAHA YB-1
I always use it for SR400.
No exhaust leaks and no complaints about quality. View detail
Replacement and machining of aged Coupler
We decided to replace the 3-pole coupler on the Speedometer side, which had deteriorated significantly over time. In addition, I decided to take out the necessary wiring directly from the coupler to cancel the intermediate harness of the Shift positionIndicator, which was in the way. Since I had just replaced the 6V MONKEY/GORILLA Main Harness the year before last, the Coupler on the body side was in good condition, so all I needed this time was Female. Quantity:I was going to buy the Set stuff, but I found a product that was just the part I needed.
For the replacement work, the wiring of the old Coupler is cut off at the root, and when the terminals are newly installed, the wiring cut off from the middle harness is added to each terminal, and the quantity is changed from one terminal to the other.:I finished by plugging the terminals into the new Coupler so that the 2pc's Wiring comes out. Now I can connect the Shift positionIndicator directly without interrupting the intermediate Harness, and the Wiring of the Front is a bit Refreshing.
The body texture is not bad, so it can be used normally without any problem.
View detail
I bought as many as I needed.
We decided to replace the 9-pole coupler on the Speedometer side, which had deteriorated significantly over time. Since the coupler on the body side was in good condition, only the female coupler was needed this time. Quantity:I thought about buying a Set item, but I found a product for only the part I needed, so I bought this one. I cut off the wiring of the old coupler at the base, installed the terminals I bought at the same time, and inserted the terminals into the new coupler one by one while checking the color of the remaining wires on the old coupler. The texture of the body is not bad, so unless there is an Accident in the future, it will not have to be replaced until the car is scrapped. View detail
OEM same etc.
I decided to purchase the Decompression cable as well. View detail