Reviews
Purchased for 23CRF250L
Purchased for CRF250L.
The minimum ground clearance is low because it is a non-S model, and also because it uses ACERBIS skid plates.
It does not fit under the Engine as it is.
I have to pull the vehicle up to get the STAND in, and when I lower it down, the STAND is stuck.
I would appreciate it if you could lower it a bit more.
I use STAND after putting the front and rear Tire on the Block because it is inconvenient.
If not for this, it would be a perfect score, but I originally had the same impresion for use on a CRF250L
I purchased at my own risk and have no problems.
View detail
Decorate your garage with Motorcycle
Think of the purpose of decorating a garage with cars off! View detail
Easy Lift up
I had a hard time deciding between this and Jack's, but I chose this one because of its light weight.
Narrow type STAND is a little unstable, but it is stable when lifting the front.
When lifting both wheels or only the rear wheel, it is recommended to fix the Front with chocks.
This was the right choice for ease of lift up and portability.
View detail
Rugged STAND
It is BoxSTAND, Off-road motorcycle owners should have at least one.
I think it would be easier to put the Block under the Side Stand, tilt it to Left, and then put it in from the body Right.
BoxSTAND is so sturdy that once you buy one, it will last you a lifetime.
View detail
It is very convenient to have it for maintenance.
[How is it used?
Purchased several years ago for storage and maintenance of Dual PurPass vehicles.
This time, we have used another company's Lift Stand that looks just like it." I am posting this because I would like to review the Lift Stand made by DRC again, as I have purchased a new one.
As of 2023, the regular price is 16,500 yen due to price hikes, but a few years ago when I bought it, it was available for less than 10,000 yen gold, including the discount from Webike.
Was the one you received as per Image?
I wanted to buy it when I saw the original at a Motorcycle supply store at the time, and I waited until the discount at Webike was more than enough to buy it.
Was the installation difficult?
Like the similar product I purchased the other day, it was packed in a box with the body part that lifts and the lever part that lifts by the principle of leverage detached, and after opening the box, it is assembled with two shafts and a CClip for fixing to look like the product introduction page by Webike.
The assembly is completed smoothly with no hole gaps, etc., without any problems.
Grease up is firmly applied to each shaft and moving parts when assembling.
How was your experience with it?
When we first started using it, there was no rattling and the vehicle was almost vertical and stable after lifting up, but after several years of frequent lifting and lowering, rattling began to appear on the inside and outside of the posts, causing the vehicle to lean slightly when lifting up (not enough to cause a risk of tipping over).
We have not taken special care of the Damper, but even after several years, we have not experienced any Damper gas loss, and the vehicle can be raised and lowered smoothly, so we believe the durability of the Damper is sufficient.
Unlike similar products, the paint is solid and to date, no paint peeling or rust has occurred.
[Was there anything that disappointed you?
There has been no disappointment to date, and the slight rattling noted above is nothing to worry about considering its age.
Other items that would be helpful
Point and hang of installation
As mentioned above, if each moving part is thoroughly greased up before use, wear and force on moving parts can be reduced, so it is a good practice.
Even if the STAND itself holds the vehicle firmly, if the ground is not soft or stable, the Motorcycle will easily fall over.
[Availability and clarity of the Instruction Manual
An instruction manual with illustrations of how to assemble and use the product is included, which is easy to understand for those who purchased this product for its functionality.
[Notes]
When lifting up, use the carBoth Sides of the car where the ground surface is as flat as possible.
Lifting up on an uneven surface can cause the vehicle to become unstable and fall over, damaging or injuring the motorcycle.
Also, be sure to lock the lock lever after lifting up.
Please make sure to check the lock to avoid the risk of accidentally touching the lever of the leverage part and causing the motorcycle to come down.
[ITEMS TO BUY TOGETHER
If you do not have Grease as a maintenance tool, purchase cheap Grease and apply it to the moving parts during assembly.
[Opinions and requests to Manufacturer
I would like to see more ColoringVariation in the Lever section, which is the leverage part, so that I can have different enjoyment when using multiple units. I would like to have more coloring variations of Blue, Lime green, and Color.:Would you like to have a Yellow?
View detail
Easy and safe raising and lowering
It is very good because it can be raised and lowered easily and safely.
I really thought Red would be safer because it would be more visible, but the price was lower for Black, so I decided on this one.
View detail
A must for anyone going on forest roads.
I bought this for Puncture repair when I go to the woods.
Convenient. That's all there is to it.
With some ingenuity, the front wheels can also be raised.
It is good to have a tube tire equipped no-motorcycle except for touring on forest roads.
I think its original use is for cleaning Chain, so if you don't have STAND, one is very useful.
There are also lifted ones, but they are bulkier and more sturdy due to their simpler construction.
It would be nice if it were a little cheaper, but I don't think it will break that often. If I had to say something, I would say that I wonder how long the Rubber will last.
View detail
![[PIT BIKE STAND]](https://img.webike-cdn.net/catalogue/images/13445/8981500002_TS.jpg)
Foldable, so it's convenient in many ways.
First, it folds up so it can be left at the end of the car.
And because it is made of plastic, it is lightweight.
It is originally intended to carry off-road motorcycles, but it can be used for other purposes as well.
When you go to practice, you can put a Polyethylene tank filled with water, tools, or use it as a chair.
It can also be used as a step when washing a car.
I have only used it a few times but the strength is perfect.
There are also areas where you can put up stickers, so you can customize it to your liking.
It is a bit expensive, but it is really useful Items to have in your car!
Recommended for Off-roadUser.
View detail
Even women can easily Lift.
Used with SEROW250 on board.
When I first used it, I was unfamiliar with it, so I had to go through a trial-and-error process to figure out where to place it before lifting it.
It rode stably during the work and was slow enough to be used safely when unloading.
View detail
Easy to use
Used for maintenance of xr250BAJA. It is very useful for tire replacement. It is also well made. View detail
It is convenient
I purchased this product for maintenance of my CRF250RLY50.
The car is low, so you have to tilt it at first, but it's very stable and easy to use!
View detail
Great stand
Received the stand in good condition and well packed as always. Product is very strong and can lift my Honda CRF300l easily. Lowering it is also convenient with the absorber provided. Recommended for bikes according to its weight capacity. View detail
For Tire replacement.
Compact and foldable, it can also be used for touring.
Of course, it can be used at home for Tire replacement, etc.
By the way, when you float the front wheel, the rear wheel, the Tire
I am CRF250L and it looks like the picture.
View detail
In case of emergency
I was addicted to Motocross since I was young, but after 50 years old, it became too hard for me and nowadays I only do forest road touring with TRAIL car. I used to do Puncture in the mountains before, and I am used to changing tires on the Motocross because I used to do it often, but I only know how to remove the wheel by lifting the Motorcycle on the Motocross Stand lol. I had to replace the tube with a new one after I fell over the motorcycle and had a hard time. After that, I found this product and bought it as soon as I found it. I have been carrying it with me all the time since then. I have not used it while touring yet, but I feel safe. It would be great if it were a little lighter. I am glad I bought it. And as a side note, you must carry insect repellent during the mosquito season. I was attacked by a group of bush mosquitoes while repairing in the mountains. View detail
It's very easy.
I have been using the maintenance STAND for Rear, but it was very difficult to use for Off-road motorcycle, so I bought the STAND for Off-road motorcycle.
It could have been something simple, but I looked for a Lift Stand because it was Large strange to lift the Motorcycle to the STAND.
There were many products available, but I chose the H2Lift Stand, which is made by DRC and has a good reputation.
It can be used with SEROW with low minimum ground clearance or CRF250 with high ground clearance.
Maintenance is so much easier now. I recommend STAND.
View detail
This is a great product for maintenance.
[How is it used?
I use it to lift up my Flow Motorcycle when I store & maintain it.
Was the one you received as per Image?
It is a very sturdy product with a Damper that makes it easy to use and easy to get off the car.
How was your experience with it?
The Lift upSTAND without Damper made by another company that I used before was difficult to handle because it lowered rapidly when getting off, but this product is easy to use because it lowers gently.
Because the lifting plate can be adjusted by the screw type, it is possible to adjust the height to some extent depending on the type of car, and it is possible to adapt it to the commercial Dual Par Pass vehicle of the large outline.
The locking mechanism prevents the lever from dropping unexpectedly even if you accidentally touch it when lifting up (assuming it's locked securely).
[Included Parts:were they on?
No, there is only this product and a simple Instruction Manual in the DanBall.
[Was there anything that disappointed you?
Due to the nature of the lift up mechanism, there will inevitably be some rattle.
I think it's acceptable because it's not so rickety that it's a tipping hazard.
0Other items that may be useful include
[Availability and clarity of the Instruction Manual
If you're looking for this product, you'll have no problem using it, but if you're cautious, search & see how to use the same product on the MAJOR video site.
[Notes]
If the lift up point of the car Both Sides is not Flat, it will not be stable, so please check the part of the car you want to lift up before using it.
[ITEMS TO BUY TOGETHER
Not particularly
[Opinions and requests to Manufacturer
It would be helpful if the rattle when lifting up could be reduced just a bit more.
View detail
I'm always ready.
I was able to help when Chain was crushed in Hokkaido and when Tire was nailed in Shimane.
There's nothing sadder than being out of action on the road and having to retire, so the more prepared you are, the better.
View detail
It's convenient
It is convenient. I have no choice but to say.
The basic purpose is to clean the Chain.
Because it is an Off car and I want to clean it on the way back from Touring and forest road.
However, a regular STAND takes up a lot of space and...
I've got two with On, and the Maintenance Stand (front and back) on that one already takes up a lot of space.
It's very easy to use. Once you adjust the length, you don't even have to hang.
I think anyone can handle it easily.
It's not something I'd pass around, but there's no reason not to buy it.
View detail
Light operation and safety with Damper
I chose DRC because I thought it was dangerous to buy cheap products.
My motorcycle weighs 140kg and is on the heavy side, but it goes up easily.
Also, the Damper works well and safely when lowering.
If you have a light body or a strong body, you may not need the lift up mechanism.
For the average person, this Type is the way to go.
If you own an off-road motorcycle, it's a good idea to own one.
View detail
These are necessary items for emergencies.
[Was there anything that disappointed you?
There was rust in the Shaft on the Inner side.
Do you have any wishes or improvements you would like to make for the Manufacturer?
The adhesion of Rubber is weak.
[Do you have any products to compare it to?
Swingarm Lift StandUN-C5025 by the same manufacturer
Frequently Asked Items
What made you decide to buy?
When I used to do Puncture on a forest road, I almost got underneath the Motorcycle when I used a piece of wood that was lying around.
How was your experience with it?
The rear Tire was able to float with no problem, but there is no place to hook the Front Tire because of the Under Cover, so you have to do some modifications.
Was the installation difficult?
If the balance is bad, you will fall over. Also, wheel stops and Brake Lock are absolutely necessary.
【Please tell me the installation point and hang】
As much as possible, work on a flat surface.
[Was the Instruction Manual easy to understand?
I had no problem with the video on Webike's Youtube.
[Included Parts:were they on?
None
[Others]
It is compact and can be used for vehicle installation.
View detail