Reviews
I can't give it to you without it. It is a must buy!
I bought this Option to use the Jay Trip , Low Roller stand (item #:JT-1052QR).
"V-receiver, 2." They say.
To begin with, I did not purchase STAND out of necessity, but I purchased YOSHIMURA's Rear Stand Bracket Set for VSTROM250SX. (M8) I had been putting on the Option (Option 1) for the time being, so I bought this Option because I had seen it being used with the Jig Sur which is almost the same as the Option (Option 2) and I thought it would be good.
As expected, it worked properly.
However, if you don't use it well, the red rubber part on the end may come off, so it seems that you need to get used to it.
I am a novice when it comes to STAND for RoadMachine, so I will do my best to familiarize myself!
View detail
Easy to insert into Fork
When inserting the STAND into the front fork hole, the STAND tip bracket is inserted at an angle,
It is a little hard to get into the holes. Once it is up, it is fixed perfectly, but it takes a lot of time to insert it into the two Fork holes.
View detail
The product is good, but..,
The quality of the product is very good, as it is made in Japan. However, the contents of the package, especially the tires and other components, smelled like cigarettes and filled the storage room. It is a pity because the product is so good. View detail
good quality
Purchased as an addition to the company's Roller stand.
I don't have to tell you about the fit and consistency. I have used it without any complaints.
However, it seems that a protruding part has been added, but I have no idea what this is for...if anyone knows, please let me know.
View detail
Combination with SNIPER
I purchased the SNIPER Racing Stand Hook for my 2019 ZX-10RR.
STAND-UP has also become easier.
View detail
I'm not sure when it was lost.
I bought it because one of the four was gone and the other was cracking.
It explains that double-sided tape makes it harder to remove.
If so, I wish they would put it on from the beginning.
It was a hassle to put it on, so I used Vinyl Tape to prevent it from coming off.
View detail
Slightly disappointed.
[How is it used?
Used in YZF-R6 (2019) with V-receiver.
I am new to buying Rear stand but have rented a Short from J-TRIP.
Was the one you received as per Image?
It was heavier than I expected, but not a problem at all.
The large size was as shown in the image, but it is still large compared to the short size.
How was your experience with it?
It is easy to raise and lower, and although I was worried about the short version, I made the right choice by choosing the long version.
However, even with Short, Stand for Beginner was easy and did not require much strength.
The screw holes are too large or the bracket is wobbly even when the bolt is tightened firmly.
[Points to note]
In the case of the V receiver, even at the lowest setting, it floats about 4 cm, so a little force is required to raise it.
If you want to raise it with light force, it is better to choose Stand for Beginner because Stand for Beginner will be in a lower position.
View detail
Fits: DUCATI Panigale 1199/1098(rear)/1198/STREETFIGHTER1198/Deer Bell MULTISTRADA 1000DS1200 MONSTER S21200/Setc., DUCATI Panigale 1199/1098(rear)/1198/Streetfighter 1198/Diavel Multistrada 1200 Monster 1200/S etc., DUCATI Panigale 1199/1098(rear)/1198/Streetfighter 1198/Diavel Multistrada 1200 Monster 1200/S etc.
Short and unsettling, but functional enough.
[How is it used?
For home maintenance and custom
Was the one you received as per Image?
As per Image
How was your experience with it?
Shaft is short and I'm afraid it will fall out.
[Points to note]
Nothing in particular, as long as it fits the diameter of your car model.
How did it compare to other products?
This price for one Shaft seems high, but I have no other choice.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Required when removing Tire.
I usually use Stand for Beginner.
When you remove the tire, you are using a V-bracing system, and it is nerve-wracking when you are handling a heavy motorcycle. If you're not careful, you'll end up on the ground.
View detail
I knew it was a special product...
[How is it used?
I purchased this product because I needed it for front maintenance of my Grom JC92.
Was the one you received as per Image?
The color was as I imagined, but the color was only Gold (Black at the time of sale?), so I thought it would be better to replace it...
Was the installation difficult?
No problem, just plug it in.
How was your experience with it?
This is a special product and can be easily lifted up by simply inserting it into the round hole at the bottom of the Stem. However, it is recommended to check the hole when inserting it to avoid hitting the Special Knife boss on the body....
[Included Parts:were they on?
No, sir.
[Was there anything that disappointed you?
The construction of the product is perfect, but I feel that the price is not commensurate with the quality.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I've been wondering whether I should buy a JT-113 or a JT-116 since I bought my first Grom, but I decided to go with the JT-113 because I have a JT-116 that I've been using for a while. The JT-113 is fine for maintenance around the wheel and brake, but for overhauling the front fork, the JT-116 and the SPECIAL Knife boss are better, so I decided to use this one. Also, I think the price is still too high.... If the price was at least 3,000 yen, I think everyone would buy the Grom Owner without hesitation, but what do you think? Also, if there were more color choices, it would be more enjoyable.
View detail
State the dimensions.
Nowadays, I don't understand the sensibility of selling such attachments without stating the dimensions.
The product itself is not particularly problematic, but depending on the condition of your Swing Arm or Hook, the Rubber cover may fall off every time you raise or lower it, which may be annoying.
View detail
Hard to buy, bulky, frequency of use
First of all, as a premise of Large, it is difficult to purchase OnLine anyway.
If you are a beginner, I would recommend Unit or DAYTONA products as there is a normal chance of buying the wrong one.
There's nothing in particular that makes it superior because it's a J-TRIP. I think it's almost like everyone just buys it because it's the only one they know.
There are a lot of maintenance stands overseas that are very well made, but they are all bulky, so the cost of transporting them tends to be high, and the selling price is not cheap either, which is a difficult thing for an island country.
View detail
Parts for Rear Stand
outline
V receiving bracket for JtripRear Stand.
Reason for purchase
I decided to buy J-trip's Rear Stand, but the receiving bracket was sold separately. There were various shapes, but the V type seemed to be stable, so I bought this one.
Bundled items
VReceiveBracketQuantity:2pc. Set
How to assemble
Just insert it into the Rear Stand side and tighten the Knob on the Rear Stand side, so it's easy.
how to use
There are many different types of Brackets available for different models of vehicles and brands.
ZX-10R (2021) But STAND (JT-125) and Hook bolt (JT-107D) combination to secure the brake lever and prevent the vehicle from moving.
I didn't know which direction the V receiver was facing, so I checked with videos and HP etc. and installed it.
The STAND was placed near the Swing Arm, and while holding the rear of the vehicle with the Left hand, the Right hand adjusted the position of the STAND so that it rested on the Hook bolt, and while holding the rear of the vehicle with both hands, the STAND was applied by stepping on it with the feet.
After lifting up, the position of the V receptacle was not so good, so I lowered it once and adjusted the position of the V receptacle by loosening the Knob, so I have the impression that the adjustment is a little complicated.
Impression used
It is necessary to adjust the width direction of the V receptacle at first, but once it is adjusted, it is relatively easy to use thereafter.
Improvements
When I unloaded the car, the rubber for the protection of the V receiver came off with both sides of the car. it was written in the instruction manual, so I think it is easy to come off.
V-ring mounting orientationQuantity:Pair (for Left and Right) It is easier to identify the Body so that the
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
Bad weld spatter marks.
[How is it used?
Installed external Stand Hook on MT-07.
The Hook is very low, so it was introduced to reduce the force required to Lift.
Was the one you received as per Image?
Unlike the STAND receivers I've purchased, there are so many weld spatter marks that they are unsightly.
A bit of a shame
How was your experience with it?
I was able to lower the Lift amount considerably by using this.
Short roller stands can also be lifted with one hand.
(Originally, you had to put your full weight on it to Lift it)
[Points to note]
Depends on the make of car.
I think that in many cases, the width is not enough unless it is STAND of Wide Type.
(Because I use about 30mm of One Side in Crank part)
View detail
![[Repair] Nut Holder 08](https://global.webike-cdn.net/photo/impression/73/73c0d503d79c3a21ac5e126c47ea635dL.jpg)
Minor change
A while ago, I found out that Rear stand has changed its model.
When I asked for details, he said they just added this part.
Version up to the current model if you wear this!
View detail
![[Repair] Nut Holder 08](https://global.webike-cdn.net/photo/impression/ed/ed0f14c27e3fc0d67e3ae1d07e2c7edcL.jpg)
It's a Repair Parts product, but it seems to be attached to the recent STAND.
[How is it used?
I used it on my original Rear stand made by JTrip.
I ordered this because I heard that it would eliminate the rattle.
Was the one you received as per Image?
It's a product made in such a way that I wonder why it wasn't made before, but I like this kind of improvement.
How was your experience with it?
It's definitely not rattling anymore!
However, it seems to be no good if the screw hole has been damaged. If you are using the old STAND, you might want to replace it once.
[Points to note]
As long as you pay attention to the direction you attach the Nut, you should be fine.
View detail
It was featured on the Commander's FB page, so...
There doesn't seem to be a STAND that can front up without interfering with Cowletc. in KATANA.
I was introduced to it when I took a peek at the Commander's FB page, so I thought I'd buy it before it was gone...
At that time, Webike didn't have it, so I bought it from another shop.
The installation is not a problem at all, but I don't know if it is individual difference or the hole under the Stem of front 16in. second type KATANA is larger than other vehicles, but with 19mm diameter, it feels like a governor.
He's got a long neck, he's a governor, and he's on the Commander's FB. "Attachment causes Lever to take effect, so riding with STAND-UP, for example... I don't want to overload it because I was warned that I would have to.
In the picture that has been introduced is Black, but the goods that have arrived are per Large? Is it Gold.
It was a shame that it was scratched a little, but it will be scratched with use, so I gave it a finish.
View detail
Ease of use is as good as it looks. How is the texture compared to the front and rear STAND?
I have a similar STAND from UNIT.
I chose this one because the storage Size is Large threshold.
The fact that single tubes are sold in 0.5m increments is just right for the Motorcycle.
1.5m×Quantity:I used 2pc and 1m ready-made as it is.
We have a Large Diameter Pipe cutter, so we can process as much as we want.
Cut the height direction a little more and make it Compact.
It looks like you might want to increase your stability.
STAND has a load capacity of up to 500kg.
It is very sturdy, large and heavy.
However, if the weight is not applied vertically, it will not be very stable structurally.
In the case of high weight, it will have to be used with great care.
The ease of use really is as impressive as the description and appearance.
The point that concerns me is that the insertion hole may be too large for the diameter of the single pipe, and
We use OthersRearMaintenance Standetc. but the quality of the paint is poor. (Weak) I have a feeling.
The availability seems to be poor compared to the front and rear Maintenance Stand, and
I wonder if they're cutting corners because there isn't much demand. I suspect that they are.
Having said that, Ideas is a good product and very helpful.
View detail
Fits: DUCATI 1098, MV AGUSTA Cantilever Swing Arm All Cars, DUCATI 1098, MV AGUSTA All models with cantilever swing arm, MV AGUSTA All models with cantilever swing arm
Don't forget to buy.
Some people might buy the Rear stand and forget to buy the Shaft.
Buy the correct diameter for your vehicle and do not forget it.
View detail
![[Front Stand Optional Parts] Boss Collar 5-Piece Set](https://img.webike-cdn.net/catalogue/webike_images/0000/0000/0155/9451294_1_TS.jpg)
Loss.
When you buy a JTrip STAND, it comes with it, but if you only use it for a certain model of car, you won't use the other colors.
I lost my Large when I decided to use it for a different car model.
Next time I'll make sure to manage it so it doesn't get lost.
View detail