Reviews
You can physically feel the horsepower increase.
I bought it thinking it would not work anyway, but after replacing it, the driving is totally different. It is easy to install. By the way, I am using the fine grit one, so I wonder what will happen if I change to the rough grit one. I am looking forward to it. Please see the official YouTube video of Mukawa for the installation. View detail
Fits: SUZUKI ADDRESS V125, KAWASAKI KSR110, HONDA PCX125, HONDA MONKEY, HONDA APE 100, HONDA GORILLA, YAMAHA CYGNUS X (FI), HONDA APE 50
KSR2 is mounted and brightness is OK.
I installed it on my KSR2 and the brightness Level is OK both in Position and in Brake. Other users' impressions were that the brightness became dark, but with the KSR2, I was able to check the brightness even during the daytime and the Level is Large and sturdy.
The LED headlight is more expensive than the Pine Stripe LED headlight, so I can't say that it has superior cost performance, but the product itself is solid and a good product.
KSR is a small battery vehicle, so if you use a lot of electricity such as for an electric tachometer, water temperature gauge, smartphone charging, etc., it is recommended to use LED headlight and tail lamps to secure electricity quickly.
Finally, the packaging has been changed from a box to a thick vinyl package. I am concerned about the packaging of this delicate product if it is not packaged properly for mail order.
View detail
Fits: SUZUKI ADDRESS V125, KAWASAKI KSR110, HONDA PCX125, HONDA MONKEY, HONDA APE 100, HONDA GORILLA, YAMAHA CYGNUS X (FI), HONDA APE 50
Brightness can be secured by attaching to KSR2
I installed it on my KSR2, and the brightness was maintained in both Position and Brake. I have seen some other people's impressions that the brightness became darker, but with the KSR2, the brightness is at a level that can be confirmed even during the daytime.
The price was higher than Matsu Stripe's LED headlight, so I can't say that the cost performance is excellent, but I think the product itself is a good product.
If the vehicle is powered by electric power (e.g., electric tachometer, water temperature gauge, smartphone charging, etc.), we recommend using LED headlight and tail lamps to secure the power.
Finally, the packaging of the product has been changed from boxed to thick vinyl, which is a bit worrisome since it is a Delicate product and if it is not packaged well, I would be concerned.
View detail
Genuine SP Takegawa Master Cylinder Lever for Honda Monkey 125
I specifically purchased this Kitaco lever as it is a billet one and not a steel one that came on the bike. The customer wanted a billet lever as a replacement anyway due top asmall fall and the lever got scratched pretty badly. I looked a t a few other brands but finally found that SP Takegawa did a cracking deal on this lever so in my basket it went. It was not really hard to find as I just used the search on Webike for this model and narrowed down categories. For what this is actually made of the price was slightly reflected in that but still, really good value from a great brand. With some other parts, my order was shipped using EMS and arrived in 5 days. The lever did comae in the SP Takegawa packaging and was well protected. The design is flawless and a really good take on a classic lever pattern. As this is billet, it is made from one piece of aluminium and you can see that in the lever. The quality is really stunning. A lovely smoothed out surface with plenty of meat on it so it will not break easily. Fitting this to the Monkey bike was just a matter of unscrewing the pivot bolt and replacing the lever. Nothing hard at all. It did surprise me but the lever once fitted does feel like it belongs on the bike anyway. The action is smooth and no notchiness. Very pleased with this purchase. View detail
Fits: HONDA SUPER CUBC125, HONDA GROM, HONDA MSX125, HONDA MSX125SF, HONDA CT125, HONDA CB125R, HONDA CB250F, HONDA MONKEY125, HONDA CBR250R, HONDA MSX, HONDA GROM, HONDA SUPER CUB110, HONDA CROSSCUB110, HONDA MONKEY125ThailandMODEL, HONDA CB150R, HONDA DAX125, HONDA CT125
This is what a luxury Lever is:??
Mukawa High Quality Lever??
Texture and structure are both good!
I just think 20,000 yen is a little too much ….
View detail
Fits: HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA MAGNA50, HONDA CUB press 50, HONDA CUB press 50, HONDA SUPER CUB 90, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA GIORCUB
If you want to Tuning engine+NORMALAir cleaner!
Used for LITTLE CUB.
After standard light tuning such as 75cc bore up, high camshaft, carburetor replacement with PC20, connecting pipe replacement for CUB90, etc., NORMALA air cleaner seemed to be a little insufficient in air capacity.
Nevertheless, we wanted to use the NORMALAir cleanerBox as it is, and we did not want the intake noise to be loud without a filter, so we chose to replace the air filter inside with this product.
Installation was very easy and the procedure is exactly the same as replacing the OEM air filter!
This Sponge Filter certainly lets a lot more air through than the paper version of the NORMALAir Filter.
In addition, when connecting to the connecting pipe of the pre-regulation CUB90, the filter side connection port is a little large, so it could be connected without loosening by filling the gap with a thick gap-filling tape or the like.
View detail
The pack of 6 replacement socket set screws sure come in handy
About quality and texture - The socket set screw from SP Takegawa is made from stainless steel and is sized at M3 x 4mm while the quality from the overall fit and finish is perfect. About the feeling of use - The socket set screw is used on the drain bolt with magnet and does a wonderful job of securing the stick temperature sensor but being so tiny are easily lost so the pack of 6 replacement socket set screws sure come in handy. Products to buy together - The socket set screw are a key part to work together with the drain bolt with magnet as is the sealing washer which are a product worth buy also. Difficulty of installation - The installation of the socket set screw is a simple task that took 0.1 of an hour to complete. Some slight mechanical aptitude and the use of basic hand tools is all that is required to secure the socket set screw into drain bolt with magnet. Cost performance and comparison with other products - I find the cost of all the products SP Takegawa sell to be on par when compared to what most other companies sell their products for and the socket set screw is no different. Having the pack contain a quantity of 6 socket set screws helps achieves this. About shipping and packaging - With there being no cost difference between sea freight and EMS for the socket set screw, I chose EMS for a earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - For my location, purchasing small common use products like this from Webike Japan is the best option when combining multiple parts together if you are also taking into account the shipping cost. View detail
I managed to get it on.
I was doing some maintenance at the beginning of the season and found Takegawa's air filter rusted.
I thought maybe I washed the car too much. I thought I might have washed the car too much, so I asked for just the filter part, but there was no part number.
My Grom is a JC75, and I need to spend another 1 man yen for the filter. Just thinking about the future... painful expense.
I looked for a lot of things, but I couldn't tell from the pictures if it would work or not.
This filter has a slightly bent duct, and the diameter should be the same on both the JC92 and the JC75.
I bought it The result was not attached.
However, since I bought it, I thought a lot about it and replaced the duct part of the filter that was already attached with this filter.
The diameter is a little different, but fortunately the filter I'm replacing is narrow enough to fit.
trial and error Yeah, I got it.
I'll have to see what else I can come up with until it's time to replace it again.
I think Takegawa should have released repair parts since it is a filter.
View detail
Fits: HONDA SUPER CUB 50, HONDA LITTLE CUB
two-edged sword
On an uphill which is also tough for a 4-wheeler, LITTLE CUB, registered as a Class 2 moped, was able to climb the hill at 40 km/h in 2nd gear. 5 km/h faster after replacing the Air cleaner. Considering only the maximum speed, the effect is clear. (I'm running 120mm wide, bulky Rear tires, so that's the only reason I can't get the Speed up.)
However, on the flat, I lost all Punch up to the mid RPM range of 1st gear 20km/h, 2nd gear 35km/h, 3rd gear 50km/h, and on an uphill, it stalls at once from 3rd gear 60km/h. It seems like there is too much air in the low to mid RPM range and the fuel injection is not keeping up? The intake sound is so loud that it even drowns out the exhaust sound of the BEAMSExhaust system.
Nevertheless, when the engine reaches the high RPM range of 35 km/h in 2nd gear on flat terrain, the Punch becomes effective and can be used up to around 45 km/h, which is above the rev limit. In this speed range, the intake sound becomes smoother and the exhaust sound becomes louder.
3rd gear missMatch GEAR ratio and EngineTorque at all speeds. (Adverse effects of RSprocket exchange) On a gentle uphill, the engine stalls even at 40 km/h in the middle RPM range, where Torque is supposed to be, and finally exceeds the Rev limit of 60 km/h on a long flat or downhill slope. At this time, there is no engine punch, but the engine noise peculiar to high rpm is heard, which is not good for both mental health and the engine.
In case of rain, a MINIBucket bought at a 100-yen store is covered to prevent raindrops from entering the intake air. (Lol)
View detail
There were no problems.
The light came on without any problem. I was able to use it normally. View detail
Does a wonderful job securing the largest sized breather hose
About quality and texture - The 15.5mm hose clamp from SP Takegawa is made from spring steel to maintain it's shape and finshed with a trivalent chromate treatment for prolonged corrosion protection, the quality from the overall fit and finish is perfect. About the feeling of use - The 15.5mm hose clamp does a wonderful job securing the largest sized breather hose to the barbed hose fitting and breather cap within the catch can system and is a much neater option then using a zip tie, with the end result being a professional looking installation. Products to buy together - A key product to buy together with the 15.5mm hose clamp is the 12mm breather hose for connecting the catch can to the engine via the breather cap for ventilation and drainage purposes. Difficulty of installation - The installation of the 15.5mm hose clamp is a simple task that took 0.1 of an hour to complete. Some slight mechanical aptitude and the use of basic hand tools is all that is required to position the hose clamp to secure the breather hose to the barbed hose fitting. Cost performance and comparison with other products - I find the cost of all the products SP Takegawa sell to be on par when compared to what most other companies sell their products for and the 15.5 mm hose clamp is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the 15.5mm hose clamp, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - For my location, purchasing small common use products like this from Webike Japan is the best option when combining multiple parts together if you are also taking into account the shipping cost. View detail
A much neater option then using a zip tie
About quality and texture - The 13mm hose clamp from SP Takegawa is made from spring steel to maintain it's shape and finshed with a trivalent chromate treatment for prolonged corrosion protection, the quality from the overall fit and finish is perfect. About the feeling of use - The 13mm hose clamp does a wonderful job securing the breather hose to the barbed hose fitting within the catch can system and is a much neater option then using a zip tie, with the end result being a professional looking installation. Products to buy together - A key product to buy together with the 13mm hose clamp is the hose connector that allows for a change in breather hose size from 12mm to 5mm as generally for the motorcycles I work on do not have the small barbed hose fitting on the motorcycle side. Difficulty of installation - The installation of the 13mm hose clamp is a simple task that took 0.1 of an hour to complete. Some slight mechanical aptitude and the use of basic hand tools is all that is required to position the hose clamp to secure the breather hose to the barbed hose fitting. Cost performance and comparison with other products - I find the cost of all the products SP Takegawa sell to be on par when compared to what most other companies sell their products for and the 13mm hose clamp is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the 13mm hose clamp, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - For my location, purchasing small common use products like this from Webike Japan is the best option when combining multiple parts together if you are also taking into account the shipping cost. View detail
Does a wonderful job securing the breather hose to the barbed hose fitting
About quality and texture - The 9.5mm hose clamp from SP Takegawa is made from spring steel to maintain it's shape and finshed with a trivalent chromate treatment for prolonged corrosion protection, the quality from the overall fit and finish is perfect. About the feeling of use - The 9.5mm hose clamp does a wonderful job securing the breather hose to the barbed hose fitting within the catch can system and is a much neater option then using a zip tie, with the end result being a professional looking installation. Products to buy together - A key product to buy together with the 9.5mm hose clamp is the hose connector that allows for an increase breather hose size from 5mm to 12mm as generally for the motorcycles I work on do not have the small barbed hose fitting on the motorcycle side. Difficulty of installation - The installation of the 9.5mm hose clamp is a simple task that took 0.1 of an hour to complete. Some slight mechanical aptitude and the use of basic hand tools is all that is required to position the hose clamp to secure the breather hose to the barbed hose fitting. Cost performance and comparison with other products - I find the cost of all the products SP Takegawa sell to be on par when compared to what most other companies sell their products for and the 9.5 mm hose clamp is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the 9.5mm hose clamp, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - For my location, purchasing small common use products like this from Webike Japan is the best option when combining multiple parts together if you are also taking into account the shipping cost. View detail
I can't start without it
This is essential when installing an external disc such as PCX on a car model that uses M6 Bolt such as Grom, MONKEY125, CROSS CUB, etc. However, the price is a little bit expensive. View detail
Fits: HONDA CROSSCUB110, HONDA SUPER CUB110PRO, HONDA SUPER CUB110
The stable Mukawa Brand!
Finally! SPTakegawa Power Filter (OEM Element exchange type)
Installation Kang Tan! Effect Outclassing!
Rapidly accelerate!
Exhaust system replacement for more power!
View detail
Air filter kit
I am amazed at the amazing effect of the simultaneous installation with F-Con. View detail
Good item
The filter area is much larger than the existing pure filter, so the amount of air inhaled is likely to be greater. That's why I feel like my bike has become more powerful after installing this item. View detail
Power Filter
I replaced it, but could not get a sense of the experience. View detail
Product # 03-01-110
Bought this as a spare for the Honda Monkey. This filter showed its best performance; I tried zero-resistance filters from other manufacturers, but with them the engine works much worse. Separately, I would like to note the high quality of workmanship, no complaints. There are no problems with installation, I recommend!!! View detail
thanks!!
It has a large area compared to the existing pure air filter, so it will be more effective for inhalation! Between dense and relatively wide, I maintained the existing version because I was equipped with a slip-on muffler I'll use it well View detail