Reviews
I can't get in...
OEM Hub SprocketBolt with Quantity:I'm going to replace the long bolt in the set, but the size of the long bolt is too large to fit into the OEM hub...
In the manual It's pretty hard. And
I don't want to say it's hard, but the size is slightly different!
There was nothing I could do about it, so I zagged the hub side with a ball board and installed it.
I thought the Off-set Plate would be attached with this, but now the hole of the Off-set Plate is too small, and the long bolt that I installed doesn't fit...
The instructions are "It's too tight, so you'll have to hit the Plate with a plastic hammer, etc."
I don't know. I don't think it's the right size.
I ended up drilling this one with a ball machine...
I didn't want to use a cheap Chinese, so I chose the expensive GCraft product and was disappointed. However, you can't go wrong as the build quality is very good.
Maybe yours is the only HaGap you have, but if you only have common tools, there is a good chance you won't be able to install it.
It requires a certain amount of machining skill and tools.
View detail
GCraft4mmOffset
This is a necessity if you have a 4J Tire on your Normal swing arm.
The brand is strong and the production is satisfactory, but the cost is Neck.
It is a product that can be satisfied if it is a little less expensive.
View detail
Ideal for fine tuning
I purchased it to adjust the clearance by widening the rear tire. At first I used the 4mm Offset Spacer of G-craft, but because the gap between the Swing Arm and the SuspensionBolt became very small, I changed it.
However, I used Stud bolt when using 4mm Spacer as it is, but the hole of Spacer did not go into the part which does not have Screw mountain, so I shaved the hole and expanded it.
It may be difficult because the parts require precision, but it would have been nice to be able to install them without machining on G-craft-to-graft parts.
View detail
To prevent sticking during OH
The next time you have to overhaul a screw head, use this guy for the countersunk screw.
Threaded mountain licks or replaced by dish Cap → OH history
Threads are dislodged without collapsing → possibility of replacement historyLarge
It's no exaggeration to say that you can tell if it has a history of OH or not by the countersunk screws in this area.
View detail
Fatty acids are replaced by MOTO!
Front offset sprocket device for the rear hub 5mm spacers Installed A reliable manufacturer's product I can use it for a while View detail
4MINI
MONKEY Swingarm 16 centimeters wide and changed to 4j foil Tire 130-70-10 so I will issue a Chain line Sprocket spacer 8m I bought it. The Stud Bolt of Normal hub could not be easily removed and it was Large strange. In the manual, it was supposed to be 28 mm, but I was 23 mm and the Sprocket was painful.
View detail
If it is Large Land Production it will be exchanged for Counter Shaft
Until now,
I used Large Land Production OffsetSprocket
The backlash is large Large Fixing plate is exhausted,
Exiting Counter Shaft,
Counter Shaft's Spline will decrease,
As it is, Counter Shaft exchange is sure when you use it
Engine full O / It becomes H.
When exchanging with GCraft's OffsetSprocket
Although the previous play was lost,
With Counter Shaft's Spline wear
A little play is coming out.
I also thought about the exchange of Counter Shaft,
As we are considering the company Counter board,
I did not exchange it.
The price is higher than that of Large Land Produce
Counter Shaft and full O / With H's labor cost
Because it is over 45000 yen,
I absolutely recommend GCraft's OffsetSprocket.
View detail
MONKEYRear 4j installed
I thought that I want to put 4j in Rear of MONKEY and I bought 4mm Spacer. My MONKEY uses Drum brake of 4 LMONKEY, but the difference between 5 l and 4 l or the size of the attached Stud bolt was too long so that Stud bolt interfered with Swingarm and could not be used.
I would like to install with Cap bolt or Stud bolt off.
View detail
Although there was the opportunity to use in order to make 5.5J wear this time and it purchased, the internal organs also of the Bearing are carried out and structure was also solid. It is recommendation!!
Although there was the opportunity to use in order to make 5.5J wear this time and it purchased, the internal organs also of the Bearing are carried out and structure was also solid.
It is
recommendation!!
View detail