Reviews
Fits: Others Universal
Less than six months later, this is what you get.
I bought it because there was room in the mounting area.
I bought it thinking it was made of Gold because it was more expensive than other companies' products, but it was inferior plastic.
Thanks to your help, I was just running, but the bolt of the Cover cracked and shattered from the receiving part of the bolt.
The structure is also bad, so if this part cracks, the Filter will not be routed through at all!
I got fed up with all the shoddy Powerfuls with Covers from all the Manufacturers, so I eventually went back to OEM.
View detail
Don't buy it.
I bought a DID 530VX3 to Crimp an existing Chain to replace the Chain, but the Crimp pin broke off and I could not Crimp it.
I managed to cut the chain by using Leutor to drop the crimp at the end of the chain and then cut it, but it seemed to break.
It was not of the least use and dumped the Gold down the drain.
I bought a similar Tool from Amazon for about 3,000 yen because the parts seemed to be usable, and it broke the same way, so I assume the contents are the same.
I ended up buying DID's Kashimaru-kun and did the Crimp, which is an OEM-specified product, and was able to do the Crimp easily and without any danger at all.
View detail
Fits: Others Universal
Broke after 3 months.
AF05E with AF35carburetor installed
Cover part is Material:Plastic, and I noticed that the Bolt was cracked from where it was stuck.
Fortunately, even if this part breaks, it is sucked in via Filter, so we have no choice but to use it as a normal Powerful!
View detail
It does not fit into the other 250 models.
I purchased this for use with Blinker relay, but it does not fit into Relay's Connector.
The shape is 250 type, but it does not stick to Male terminal because the direction of the terminal is 180° opposite to Connector.
It has no use as a Connector.
This ConnectorSingle Body can be used as a Harness, but I don't think that is what a Connector is.
View detail
Easy to use
Easy to use for Spring View detail
I can use it
Crimp is no problem, but Chain cut is a bit difficult, so let's sander it! View detail
No good
useless
Garbage box
Material has problems and is too soft.
View detail
I was able to adjust it properly.
I have used it a total of three times on my medium and large motorcycles and have been able to adjust the oil level well each time without feeling any deterioration. (Purchased 1 year ago)
After use, I clean it lightly with Parts cleaner before storing it, and it has been used without any problems.
Cost-effectiveness is also Large, so a dedicated Tool is useful! (^^)
View detail
I think it's cheap, but not cosmetically pleasing.
Maybe it's just something I happened to purchase.
Crimp pin was not very durable, and I could not successfully Crimp from about the 3rd Chain.
If only Crimp pins can be purchased at a discount, this would be fine.
I used to use KTC, but I would have preferred to buy that one, even though it was several times the price.
View detail
Tanaka Shokai Tanaka Show Kai Chain Tool&CrimpTool set
This is the first time I have purchased a ChainCutter&CrimpTool set. New RKBlackChain replaced 。 The tool is easy to use and a very good product! 。 Please try it outRecommendation. View detail
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Better than expected.
Used in GORILLA.
It is Chromium Plated on Steel, which is better looking than the pure Black of other Manufactures, and the accuracy does not seem to be bad.
View detail
Touch of Lever has improved.
The NORMAL fork and wheel may be a little too much, but it is much easier to maneuver and touch.
Also, the drum-like part that goes into the lever on the wheel side was not thick enough to fit, so I had to use the previous part to make it fit.
I think I ordered what I saw because it was my first time using the site and I wanted to be sure to check it carefully next time.
View detail
Easy to use
Cheap, but easy to use, and made it easy to change the Exhaust System. View detail
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Too cheap, I'm afraid, but...
It will be needed once the NSR50 Wheel is installed.
It is cheap and too inexpensive compared to GCraft and others, but it is Chromoly steel, so it will be Large sturdy. 16T and no Limit interference inside the Crank.
View detail
Fits: HONDA SUPER CUB 90, HONDA SUPER CUB 50, HONDA SUPER CUB70
Dear CUB riders
The CUB has a light bulb that often breaks due to vibration.
This is the fate of a single cylinder engine without a balancer.
This is especially true for vehicles that have been bored up.
I think it's one thing to ask a motorcycle shop to do it, but it's easy to replace the bulb in the CUB, so by all means, keep it in reserve.
I Quantity feel the hassle of buying every single bulb.:I bought it in Set.
This is a complete set, so it's really convenient.
It's cheaper than buying from Single Item.
View detail
Good product
It is a good product 。 Wood, needle, wire brush hair (Wire) I used to substitute with etc., but the dedicated product is still good.
However, it is inevitable in nature, but the finer the material, the more delicate it is to store and handle it.
View detail
Underpriced TANAKA
I bought it at the same time as the EK520SRX2 and used it to replace the Chain, but I lost the Chain at the Crimp stage and the Rivet Pin was crimped and the Tool itself became useless.
That's a minimum quality product!
Thanks to that, all of our plans for a 4-day weekend are ruined, and we can't afford to lose 4,500 yen! I purchased the Crimp tool separately and am waiting for it to arrive, but I can't ride my motorcycle until then.
I'm most upset with myself for trusting it because I'm dealing with Webike.
I learned that sometimes fraudulent products are sold because it's only a net mail order.
View detail
It's your first time, and that's why you failed.
I bought it when I first replaced Chain.
I think I could have used it a bit more if I used it properly, but it is a good memory that I tightened it so hard that it broke the pin.
View detail
Fits: HONDA MONKEY, HONDA GORILLA, HONDA CHALY, HONDA DAX
Great quality
Made with very good quality metal, fit snug on drive shaft which is what you want, will definitely purchase this item again when/if need another one. View detail
At a minimum [Color] Clear
My lot (Purchased in 2016.) was accompanied by a translation (please enter here Instruction Manual) I was unsure of how to use it, so I checked the Net for examples of its use and referred to many of them I was worried about it, so I checked the Net for examples of its use and referred to many of them as well Also, unlike the photo posted, only the Crimp pin seems to have a different Material It is a silver molding color
The Bolt for extrusion is turned by using the 14mm Socket + Ratchet without using the attached rod I did
For both Cut and Crimp, don't turn it all the way to the end at once, especially Crimp 5 times slowly I worked while repeating the confirmation by dividing it into about 2 parts, and completed without problems In addition, when you apply LargeTorque, there is a sense that the mouth of the Tool opens slightly
Also, the angle of the tool was slightly off when tightening You should check to make sure it's straight, or be persistent while working
I also worked on the part of the chain that was sprocketed to prevent twisting
The quality of the product seems to vary and there are some concerns, but that's the Manufacturer (Seller) We expect the response of the
I didn't expect it to be easy to use as I think it is the cheapest of its kind It does a decent job as a tool and seems to have no problem with repeated use, so I'm happy with it
View detail