Reviews
It is highly windproof, so it is a recommendation for those who are worried about running wind measures.
Even with a full face or system helmet, the riding wind coming in through the neck will chill the neck and nape of the neck. This can cause loss of energy and distraction, so it is important to prevent wind from entering the neck, wrists, and ankles as much as possible.
Windproof Neck warmer is also effective in keeping out the cold to a certain extent, but it is quite difficult to shut out the driving wind that invades the Helmet. It is not always possible to fill the gap between the helmet and the neck well, and when you shake your head to look behind you, it can twist and create a gap.
So I bought a Balaclava-shaped full face mask, thinking that it would completely protect me from the driving wind. As a result, I almost achieved my goal, but since the wind protection effect is only on the front side, the fabric gradually cooled down by the wind around my neck, and the area around the nape of my neck started to get cold. Also, when I looked back, there was a gap around my collarbone due to the Gap.
Still, it will eliminate the direct contact of the running wind with the skin, so it will work just as well. Hopefully, a little (500 yen) I would be willing to pay a little more if the price goes up by about $3.00, so I would like to make the entire Neck section windproof and a little more. (about 5 cm) If you could make it longer, there is nothing to say. So I will give it 4 stars.
View detail
Looks are the top priority, so it is very Parenthesis good!
I usually wear 26.0-26.5cm, but these boots were too tight for 26.5cm, so I decided to go with 27.0cm, which is a little larger. I would not have bought it without the Fastener. Still, because of the slim design, I had to open the fastener all the way by hand to get my foot into the Smooth.
The fastener cover is also very nice, as it prevents the frame of the motorcycle from being scratched by the fastener, which is not necessary if the fastener is on the outside of the boots, but it is a bad parenthesis.
I thought the toe part had a built-in Shift changeGuard, but it does not. That said, the leather is thick enough that my thumbs did not get sore after 3 hours of driving 120km or so on a mountain pass.
I heard that there is a Protector in them, but I am not sure because they are not thick enough.
The looks are outstanding and this is a traditional NAKED to ride with. (GB250 CLUBMAN) It is the best Fit for the "I", but the functionality is secondary. The soles are not very thick, but they are hard, so quick movements are not a strong point.
View detail
Just fit for Traditional NAKED!
My middle finger length is 8cm and palm length is 11cm (19 cm in total) So, L Size is almost Exactly, but not so Tight, so thin Inner Gloves can be used.
As DAYTONA's goal, the design is just right for the traditional NAKED. The shirring on the outside of the fingers is stylish.
The sewing is solid, the leather has a good texture, and the palm is slightly suede-like, which makes the Grip less slippery.
It seems to have a thin padding, but since it is a Short Type, it will not be usable in midwinter. Also, there is a light punching processing, but it cannot be used in mid-summer, and even so, it can be used until early summer. Therefore, I think that these are the Gloves that will be used for the longest period of time in a year, though they are used in 2Season from early spring to early summer and from early fall to early winter.
View detail
Fits: HONDA GB250 CLUBMAN, HONDA MVX250F
The texture and shape is so nice that you can hold the Lever all the time!
The adjustment range is quite large, which is convenient, and the large 1-Click angle makes it easy to see the effect. However, the furthest away is too far away to grip, and recently it is too close to full break or full clutch cut.
The color is very nice, I chose Titaniumium color for both Lever and Adjuster, and it matches the traditional atmosphere of GB250 CLUBMAN EXACTLY. I could have chosen a gorgeous color for the Adjuster with Accent, but I think it would have floated around the Handlebar of GB250 CLUBMAN, so I am glad that I chose the same color.
Once, Side Stand didn't go down to the end and I tipped it over, but thanks to Foldable, the lever didn't break! (Lol)
I am satisfied with the WW because the reversible function worked perfectly.
View detail
If it could be positioned more precisely, there would be nothing to say.
The Arm that holds the Mirror rotates parallel to the Handlebar and positions it to the Large side, but it cannot be fixed at any position. If the Arm is fixed by extending the Arm outward from the Handlebar End, the width of the car may become too wide, which may be illegal. If the Arm is fixed by extending the Arm outward from the Handlebar End, the width of the car may become too wide, and it may be illegal.:), so just moving it by 1Click is quite inward, and your arm is reflected in Mirror quite a bit. Naturally, you cannot see directly behind you. This is a little disappointing.
Triumph's Bar end mirror looks like it would be easy to see.
View detail
Body is soft and very easy to use.
Both the Frame and the Shield are made of soft resin, so they are very easy to use, and the Strap's elasticity is not too strong, so you can remove the Goggles. (Shift to the forehead part of Helmet) There is no time to be stumped.
The frame and PackingSponge are not very thick, so the fit in Single Body is high, but when worn over a helmet, I think the PackingSponge will not reach the face if the Jet helmet is thicker. However, I don't think this is a problem unless it is winter time. It does not adhere to the face, but there is a rubber lining on the inside of the Strap to prevent slipping, so it will not gap while riding. In fact, the pressure feeling is reduced, so you could say that it is an effect of the Plus surface.
Standard Equipment's Shield is [Color] Clear, [Color] Smoke (Black) Shield is also included. I'll get right on it. [Color] Smoke has been replaced with Smoke. To replace the Hook, simply remove the three Hooks, replace the Shield, fit it into the Frame groove, and fasten the Hooks.
[Color] The Shield of Smoke looks quite dark from the oncoming traffic side as shown in the picture, but not so dark from the person wearing it. Even if you enter Tunnel with it on, (I don't know how it would be in an occultic Tunnel with little or no lighting.) With a little bit of lighting, it was never pitch-dark and I could not see anything in front of me. Of course, it is not usable at night. (I've decided not to ride at night.)
I would appreciate it if you could sell just the Shield separately in case it gets scratched by insects, jumping rocks, etc.
View detail
Fits: SUZUKI V STROM 1050, SUZUKI V STROM 650
Purchased for Loading Hook
I purchased this for the installation of the Loading Hook.
I may replace the Blinker sooner or later, so I need one with Service hole.
It is well made
View detail
It is moderately small and good!
It is moderately small and suitable for mounting on NumberSIDE. View detail
I put it on as a spare.
External Fuel filter attached to ESTRELLA.
It has been immobile for a while, and you can often find a little bit of age-related deterioration in various parts of the car. 。
There does not appear to be any fuel seepage, especially in the Fuel Cock area, but there is no denying that the Fuel Cock has deteriorated over time.
The other day, I was worried about the rust in the fuel tank, and although I have removed rust to prevent impurities from entering Gasoline, I am not sure about it, so I will install an additional external type of fuel filter.
Fuel filter
A filter device used in automobiles to filter fine impurities contained in fuel.
It is used for the purpose of removing water, sand, and dust mixed in during refueling, etc., and maintaining sufficient fuel efficiency.
There seems to be a time for replacement, though not up to the air filter.
■ 50,000 km at Carburetor Vehicles
■Injection car with 100,000 km
■Diesel car with 50,000 km
is the standard.
Continued use of the filter past its replacement time will not only clog the fuel filter element and cause a lack of engine output, but will also cause the filter to lose its original function of capturing foreign matter and separating moisture.
[When the fuel filter clogs.
‥
Idling of ▲Engine is unstable.
Engine seems to stop when driving.
▲ Suddenly, Engine stopped spewing.
Failure to start = Engine will not start.
I haven't experienced the clogging of the Filter yet, but considering the distance and age, it should be replaced. 。
In my 90's ESTRELLA, the fuel filter is integrated with the fuel cock and inserted into the tank. That is not so bad, but I wanted to be sure.
I also added an external Type as a spare.
I chose KIJIMA's because it was inexpensive and I had used it before.
The deciding factor was the transparency, which makes it easy to see dirt.
Replacement procedure.
(1) Fuel Cock is turned off
↓
(2) To be sure, Gasoline in the carburetor should also be removed.
↓
(3) Interrupt the fuel filter between the rubber hose connecting the fuel cock and the carburetor.
It is wise to prepare Oil Resistant Hose separately because OEM Hose is not long enough.
↓
(4) Turn on Cook and apply Engine.
Operation check.
Fuel Cock flows by Engine pressure.
after replacement
No problems
They seem to be getting rid of the impurities for sure.
Durability...? I think Large is durable because it is inexpensive and will be replaced with a con stunt.
It is a good idea to have insurance on older Motorcycles.
Installation is also easy.
View detail
Lowdown
After much deliberation, I decided to go with EFFEX and it was the right choice.
Thanks to the fact that it is a little more than two centimeters lower, it will stick with sticky feet.
View detail
72JAM Shield
I have wanted a 72JAM Jet helmet for a long time, and with that Shield, bingo! It's the best! View detail
I was looking for something like this.
It was needed for Blinker installation. View detail
![[Highsider] Turn Signal Proton TWO](https://img.webike-cdn.net/catalogue/images/129660/17308_TS.jpg)
Small and wonderful.
Blinker is better for Small. View detail
![D604 [80/90-17 44P TL] Tire](https://img.webike-cdn.net/catalogue/images/124173/D604f_TS.jpg)
Anyway, it was hard.
The CT125 Rear tire GP-5 has 2,0mm left, so I'll change it after a few more runs, but I'm running a GWCampaign, so I'll buy the Tire while I can, and I'm in the On 9, Dirt 1 ratio here, so not completely On road, I decided to go Adventure oriented.
So, after much deliberation with the well-reputed Anakee STREET, I decided to go with D604, which has no Reviews at all, as I am a minority, and write my first Review.
In a review by a certain Large River in South Brazil, the only negative image was that it was hard and vibrated.
After touching the one that arrived at my house for a bit, I was prepared that it would be hard and tiring, as it reminded me of the T63 thing from company M.
Now, when I got it in my hands with the usual Pattern, I already wanted to replace it, and I had planned to replace it next month, but I started to do so (laughs).
As you might expect, there is a direction of rotation for installation, so we carefully checked the direction of rotation before starting work.
This is my first time to replace Tire on CUB, but I will follow the theory here.
The GP-5 has a soft bead and was relatively easy to remove.
Now, let's start the assembly.
As usual, apply a generous amount of Bead wax.
Unlike off-road vehicles, we do not want to scratch the rim, so we use rim protector while working.
It's already hard even to fit the first time!
Fit the One Side and put in the Tube. These are not so fiddly.
Turn it over and put the other side in, but it is hard anyway!
After fitting half of the wheel, I held it down with my foot and lever it in, but the remaining 20cm or so was tough!
The installation was done carefully, boldly, and by brute force.
We managed to complete the work without any holes in the tube and with a clean rim.
I ran the car for a while, and it is true that the slight vibration from the Rear has increased, but it is not at a Level that bothers me that much.
Grip is often seen as such and such, but well, it is a CUB, so it can run and stop normally.
We don't ride in the rain, so as long as the dry grip is good, it's fine!
The groove is somewhat larger than GP-5, and the block is also larger, but the tread surface and SIDE are harder, so I think it is easy to be played on the dirt.
Muddy terrain is likely to Stack if not driven well, but the CUB does not have that kind of driving ability to begin with.
If you are used to working on CUBs with Spoke wheels, and if you are used to working on them, and if you drive in an adventurous manner, recommendation.
I thought that GP-5 would be easier to work with when Puncture was done, and that in the end the standard Tire would be the best. I thought that the standard Tire would be the best in the end.
View detail
![Tank Lock [MT505]](https://img.webike-cdn.net/catalogue/images/27457/94562_TS.jpg)
Replaced the company's XS319
We were looking for a replacement for the company's XS319 Fastener, which we have been using for several years, due to damage to the Fastener.
Main compartment holds a smartphone (Pixel7pro), a bifold Wallet, an electronic Cigarette in a Case, and Toilet paper instead of Pocket tissue
With the XS319, I had difficulty handling the Cable when charging my phone, but this is not a problem with this product!
The Pixel7pro does not fit into the smartphone storage pocket on the back of the lid because it is not wide enough.
I think the width of Xperia1II used for Navigation is the limit (although it is slightly long).
View detail
Both height and width are just right!
[How is it used? The Handlebar I was using before was too low.
Was the one you received as per Image? Position is now easier as recommended by Shop.
Was the installation difficult? Drilling was required for the Mirror Holder, so a Drill is needed for installation.
How was your experience with it? Long distances are now easier.
View detail
tw200
[How is it used?
Touring
Was the one you received as per Image?
yes
How was your experience with it?
good
[Points to note]
None
How did it compare to other products?
good
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
fall
If I put it on Normal seat, I think it will be a little forward and downward.
My Seat has no problem because I have removed the anchor, so the Seat is like a crescent moon, and the footing is even better.
View detail
![[Repair Parts] Cam Sprocket 28T for Regular head](https://img.webike-cdn.net/catalogue/images/119029/00-00-2427_01_TS.jpg)
Regular headRepair Parts
Although the Mukawa Regular head has been discontinued for quite some time, it is helpful that Repair Parts are still available.
I think I can still extend the life of my Regular head. (Lol)
View detail
DAYTONA Grove
As the name "Vintage Line" suggests, it looks good. Perhaps it is because of the goatskin leather, but it feels a little stiff, but it may become a just fit as you use it. View detail