Reviews
There is a LARGE difference between with and without!
The chin portion protrudes from the helmet shape, so it was easy for wind to get caught in the helmet, but this has considerably eased the problem.
It is essential for winter and high speed driving!
View detail
If you are interested in Helmet's Size, you can find it here!
Best of all, it is inexpensive!
This Sponge can be cut as well as pasted, so the size can be adjusted by pasting it on the part of the Helmet that you are interested in.
In my case, the size of the Helmet I purchased was a bit Oversized.
We were able to match them beautifully.
Many modern helmets allow you to adjust the interior, but you can use basic subtraction to make some of the interior Sponge "Unplugged." Because it takes shape,
A little tighter..." If this is the case, there is no other way but to replace the interior.
I think it is possible to try this product for a while before that.
View detail
For X14 Interior Repair
After washing the interior of my X14, the Sponge on the top of my head was falling apart, so I bought this product FOR REPAIR.
Cut the missing sponge part to a large size, and cut it further so as not to block the air hole part.
Attached to firing Styrene on HelmetBody.
You can easily cut it into any shape you want with Scissors.
The original Sponge was sagging, so even with 6mm thickness, the Fit feeling seems to have improved.
View detail
To adjust the size.
It is just right for Helmet Position adjustment, easy to use! View detail
Replacement brings Helmet back to life!
Since this is the part that deteriorates the most, Helmet was revived after the replacement.
Hold of the whole Helmet is also getting better, and if you start to worry about deterioration.
Early replacement is recommended.
It may be a little hard to remove, so be careful not to damage it.
Required.
View detail
HelmetSize adjustment
There are many different Size Adjustment Sponge for Helmet, but I think this WINS product is a very good product at a very reasonable price.
The Instruction Manual says to remove the InnerPad and attach the adjustment pad to the InnerPad, but I attached it to the inside of the helmet body. 。 It was more securely attached that way.
Oh, and the back of the head and overhead Pad came in two pieces each, so very affordable.
View detail
It is easy to use.
I used it to adjust the interior of X-lite's X-803 RS.
I had the fitting done at the FiveStar store, but after using it for about a year and getting used to wearing it, I purchased this item to make it tighter.
The feel is good, and the double-sided tape is rather strong and can be applied firmly. The tape is wide, so please cut it as needed.
This time, we increased the top and back of the head area, and also increased the cheek pad slightly.
I checked afterwards, and the fine tuning was successful and made it difficult to Gap even in the Circuit speed range.
X-lite costs about 9,000 yen for the Cheek pad alone, and it cannot be fine-tuned, so having a product like this is very helpful.
View detail
Worth a try, for fine tuning, before replacing the interior.
It is said that the best way to select the size of helmet is to try it on, but the best way is not to try on a new helmet, but to try on a helmet that has been used to some extent and the interior has become accustomed to it. (Hetero) The condition would be desirable, but then I would have to try on the ones of people I know, and the MODEL I want is not always available. In general, helmets are not replaced that often, but the interior will always be worn out. Even if you choose a tighter fit when it is new, it may become looser than expected. In my case, with ARAI, I am JUST an XL when new, and an L is too tight, even assuming interior Downs. But I am an ARAI believer and have 4 Helmets, all ARAIRX7. I have 4 helmets, all of which are ARAI RX7, and I use them according to the motorcycle I ride and the wear I'm wearing at the time, but I still have a bias in how often I use them, and even with the same model, there are differences in fit. I like RX7X Kiyonari Birdco, which I have been using frequently recently, but when I ride Panigale, which has a tight forward lean, sometimes it becomes forward leaning, so I thought about changing the ARAIOEM System interior from the standard 7" to 10", but it is made-to-order and the delivery time is 3 months! The price is also about 4,000 yen.
So we decided to try this product anyway.
Result? ... ・ Except for the cheek pad, the fit is considerably improved, but not too tight. It is also less likely to drop forward. The only thing left to be seen is how long it will last, but since it is inexpensive, I will replace it if it gets loose again. I bought two of these for other helmets as well.
Easy to install. Kitchin and Quantity:If you set the double-sided tape, the adhesive will not shift in some places. It may be better not to stick the double-sided tape too tightly, considering the possibility of positional adjustments or replacement.
In the case of RX7X, the air inlet hole in the center is covered, so we cut that part only.
I would recommend this to anyone who wants to regain the fit of their favorite helmet that has become a bit loose.
It's worth a try.
View detail
Any Shield.
In addition to the 72-jam Bubble shield, it can also be used with Universal's Shield for Jet helmets.
Installation is easy and the adhesive surface to the Shield seems strong.
When run, the Shield is properly prevented from lifting.
One drawback is that our Shield has a wobble on the upper hook that makes a grating noise while driving.
View detail
Deodorant effect and sweat absorption effectLarge!
When touring in the summer, sweating and the smell of sweat make the inside of the helmet smell very unpleasant. The Helmet liner that I installed this time is not only deodorant effect and sweat absorption, but is also good because the hairstyle does not fall apart too much. It is also a high cost/performance product. View detail
The wind path is more effective than the AirHead
I used to use the AirHead, but the protruding part was painful and I couldn't get used to it, so I replaced it with this one.
It doesn't prevent your hair from falling asleep like the AirHead does, but it's a great way to fit in naturally when you wear it.
The wind passage feels significantly more than the AirHead.
View detail
You can't go wrong
I used it on my Jet helmet which I was unhappy with fitting I am very happy with the fit and there is no gapping after installation It's just one coin and it's my favorite helmet View detail
ROUGH&ROAD Helmet Spacer
I bought this "spacer" to raise the seating height my Shoie GT AIR. I would have view issues when I would ride at high speed or leaning into the corners. By raising the way the helmet sits on my head, I could see more. It worked well. Then I bought the new Shoie NeoTecII and JCruise. Strangely enough, I believe that Shoie changed the sizing on their helmets as both helmets fit fine in the cheekpads, but loose around the cranium. I took my ROUGH&ROAD Helmet Spacer and installed it in my J Cruise and the helmet now fits fine. I might have to buy XL helmets in the future, but right now, I'm sweet thanks to this product. View detail
Helmet perfect fit Fit ♪
SHOEI's Off-Road Helmet "VFX-W" I used this product for M Size.
When I was continuously running long in the off-road, I noticed that Helmet's interior paddle was getting wet with sweat, and gradually the Helmet's Front was slipping downwards.
But, S Size feels that it's too small, and you can try replacing it with a new gold quota - - -
So the off-road companion taught us this product.
If it is this price, even if I fail, I feel like giving up, so I bought it!
There are things of 6 mm thickness and 10 mm Thick, but purchasing 10 mm Thick by Cut with Scissors and easy adjustment.
First I removed Helmet's interior pad and tried applying this item.
There are six legs radially extending and there are particularly long legs by 1 pc. It seems to be basic usage to set this to come to Helmet's Rear. I also did so.
Try fitting all interior Pad of Helmet back.
Because I did not cut one place, I wonder whether it will be too tight - - I thought, but I was happy to have a good feeling with a single shot.
Then disassemble again, peel off the Tape of this product and pasted it. Six legs stuck to the periphery so it was hard to paste slightly, but in the end it could be pasted without problems.
After that, she suffered 100 consecutive minutes at Enduro race, but Helmet did not go down as usual.
Also, though I thought that I had a headache when I had a hard time with Size, fortunately I was durable with Large.
Very cheap, I was able to easily make Helmet to Exitly Fit myself ♪
I appreciate my friends who taught me.
Recommendation!
View detail
Fine adjustment of Helmet
Purchase Helmet's Size fine adjustment.
You can fine-tune Size if you get a little Large.
The price is reasonable and texture is satisfactory.
There are also two types of thickness Please purchase according to the application.
View detail
It will not be a Mohawk
There is a groove in the inner parietal part of SZ - RAM 4 so that air can pass, but as long as I am wearing short hair, my hair does not go to sleep there "Petit Mohawk" Become.
By attaching this, it will not become a Mohawk.
It would be nice to wear Inner Cap, but it became troublesome and found this product where I was looking for a substitute Mohawk countermeasure article.
Although it has nothing to do with the original use, people with similar troubles can try.
View detail
It purchases for Helmet change. Being caught too is since I am disagreeable.
It purchases for Helmet change.
Being caught too is since I am disagreeable.
View detail