Reviews
Cannot be installed with Carrier
Ease of use of Helmet lock is normal
Installation was easy with tools.
Note that if a KIJIMA Rear Carrier is attached, it will overlap the Pipe and will not be usable.
It's about making sure you use other locks.
View detail
moderate [Color] Smoke
Especially in the summer, from the prevention of eye fatigue and designability. [Color] Smoke was selected. My personal impression is that the center line is not lost even in the Tunnel, and the blackness of the Tunnel is just right. [Color] I think it is Smoke. The photo shows a comparison of the inside of the Shield with and without a white paper placed inside the Shield, and with about 1 meter of frontal light shining on the inside of the Shield. During the daytime, the inside of the Shield was not fully visible through the Mirror because of the Visor's shadow.
Also, the curvature of the Shield is Large, so distortion is a concern, but it was not a concern with this unit.
More importantly, the reduction of outside light that I expected from Inner Shield is only (I would) recommend using this product only in true backlit situations, as the distortion of the Shield is a painful Level when used for long periods of time. In that sense, I think this product is effective.
View detail
helmet
This helmet has nice form, Glass can removed easily and I can stick the 1973's Honda logo to cover the screw hole to attach the glass look so fresh and classic View detail
Installation of helmet holder on XSR125
We install most of Motorcycle's helmet holders on each vehicle we deliver.
As usual, it is useful for Helmet lock when parking the bike.
It is a vehicle specific product, but I had to shave it down a little to install it because it hits the side cowl a little.
View detail
It is the best cospa
Nothing to complain about. It is a safe Brand. View detail
Place Helmet on Top Bridge and lock it.
The standard helmet holder of ZX14R was placed on the Left Tandem Footpeg, but when the exhaust system was replaced, the Tandem Footpeg was removed and the helmet came in contact with the silencer. The silencer is no longer used since it is placed on the Top Bridge because the rubber may melt when the silencer is hot.
I had been leaving it unlocked, but since I bought a new helmet, I was concerned about theft and decided to purchase a retrofit helmet holder.
It was attached to the Multi Bar with Smartphone Holder so that the Shield could be opened for easy key operation.
It lacks a SMART appearance, but it has achieved its purpose for now, so I will use it for the time being.
I might remove it if I can't stand it anymore (laughs).
View detail
To relieve the anxiety of a short break.
I bought this product because the CBR1000RR SP sc77 does not have a Helmet holder in OEM and there is no Screw hole to install a Type product that mounts on the Frame.
I used to hook it up to Mirror when I took a break at a touring destination, but it was half the fun with the fear of theft.
After installing this one, I was able to leave the vehicle body with some degree of peace of mind, so I think it is actually quite cost-effective as a cost-effective solution.
Installation is not particularly difficult as long as the size of the car body is carefully checked.
If I had one request, I would have liked the key to be 4-digit instead of 3-digit. I thought that if you leave for a long time for meals, etc., it might try all patterns and be unlocked.
View detail
It peels right off.
For Z8,,
2023/03/20 Purchased a Blue Type of this
2023/09/12 Red Buy this
I didn't want to change the color.
Mirror coating on the surface peels off quickly.
Coating to repel water is still peeling off easily, even the mirror part is peeling off.
At first it peeled off when I wiped it with SurLuster0, which is self-inflicted because the warning on this product says to use water only and apply Towel lightly....
(Mirror shield on Z7 didn't peel no matter how much I scrubbed it, so ......)
I was careful with the new Redi Type, but even with very careful care, it was peeling.
This is a RECOMMENDATION for those who can afford to replace it in six months.
The attached image is fogged up with breath for clarity.
View detail
Looks as good as expected
Buy Blue in Semi-smokeBase.
The color of the look is beautiful, just as I expected.
I wore it and actually saw it running, and the visibility [Color] Clear and no problems.
Mirror coating peels right off." I have not experienced such a problem with the one I purchased, so far.
View detail
Second, ◎ on ThirdHelmet
[Glasses etc. The head is SHOEIx-twelve L Size].
This is my first ShieldJet. It's comfortable, no shaking, wide field of view, and no wind in my face! I used to use a half cap for a little riding, but I don't need it anymore.
Once you get used to it, you can put on and take off the helmet while wearing Glasses. Loose around the ear Space may be working. Perhaps that's why head circumference (Around the forehead) and the chin area seemed tight. Size is Small. I can understand the opinion that. … or maybe I should have tried wearing an XL. (Sweat)
I did not feel any discomfort from the wind from the Shield, including the sound. I felt coolness around my temples, but there was a buzzing sound instead. I tried driving another motorcycle at nearly 100km/h, but there was no change in the loudness.
Shield is virtually fog-free! If you drive out a bit, I can say that none of them are. In winter (It was a warm day.) This impressed me.
The quality of the paint, buckle, and shield opening and closing is generally high, and the level of satisfaction is high. However, when you wear it, the well feeling when you hold it is not like a certain Top model, and you feel the price range. Quality and texture The 5 star rating of "5" is a cosmetic evaluation.
View detail
SlimBase
Slim and solid. View detail
Not bad, but ….
I put it on SHOEI's GramStar.
I was going to replace it with Mirror shield, but when something that looked white was released, I bought it.
It is a Pin lock modoki, but it is a mysterious product with color.
As you can see in the image, it does indeed add color, and the view you see is a Yellow color.
At first I wasn't sure about this, but once I got used to it, it was easy to see at night.
It was unfortunate that it was more transparent from the outside than I had expected.
Also, the installation was moderately Large strange. I found an official video of the installation, but I could not imitate it because it seemed that they put so much effort on the Level. I could not imitate it.
Large was strange depending on the direction of warping, but I managed it.
View detail
Very good product
I like it because it is Design cleaner than other companies' products.
Installation was easy and the feel is very good.
Spare key is also included.
The bolt is also a stainless steel bolt.
View detail
Lightweight, cute Design, cute box.
I like this helmet because it is lightweight and has a cute Snoopy design. I like how easy it is to lock and release the chinstrap. The box design is also cute, so it makes an excellent present. View detail
Fits: DUCATI MONSTER1100/S, DUCATI MONSTER796, DUCATI MONSTER696, DUCATI MONSTER796, DUCATI MONSTER696
Might be easier to use.
It can be said that it is easy to hook because of its large opening, but it is difficult to remove it without using both hands.
It happens to be the place where the Battery Charging Cable is out, so you should think carefully before attaching it.
View detail
Fit feeling is good for a foreign-made Helmet.
Many foreign-made helmets, even AsianFit, are narrow for Westerners, and when worn, there is often a feeling of pressure from the SIDE and an impact on the ear area when putting on and taking off.
I feel a little pressure around Teak, but I don't mind it because I expect it will wear out after use.
However, the cap appears to be slightly larger in size, so from a third-party viewpoint, the silhouette is a bit too big for the head.
The paint job and interior texture are good, and the design resembles Armour's Helmet, which appears in the famous game "H◯LO.
The PeakVisor is even more similar, but this Visor is difficult to use. It may be a matter of getting used to it, but when I tried to close the open Shield, I accidentally picked up the Visor and couldn't close it. "What? It won't close!" This can be the case.
Shield also seems to be slightly distorted in the forward direction.
In addition, the Knob for opening and closing the Shield is located directly in front of the Shield and is small, making it difficult to pick up and operate depending on the Gloves.
Weight-wise, it is hard to judge since it is the first full-face, but looking at the Specifications, I think it is slightly heavier.
Considering the price and other factors, I think this is a well-made product overall.
View detail
Fits: Others , HONDA MONKEY125ThailandMODEL, HONDA MONKEY125, HONDA PCX160, SUZUKI GN125-2F, YAMAHA YB125SP, YAMAHA XTZ125, KAWASAKI KLX125, KAWASAKI D-TRACKER125, KAWASAKI Z125PRO, KAWASAKI KSR110PRO, KAWASAKI KSR110, YAMAHA XT250SEROW, HONDA CRF250L, HONDA CRF250RALLY, HONDA Dunk, HONDA MAGNA50, HONDA XR100 Motard, HONDA XR50 Motard, HONDA APE100 TypeD
Nice little addition to my Monkey 125
I live in an urban area and wanted to keep my helmet locked with my bike although theft is not too common here. The stock helmet lock is located at an awkward spot that's too low and inconvenient for me - I had to try out this one. Installation is easy, product works as promised. View detail
Fits: Others , YAMAHA BWS 50, YAMAHA BWS125, YAMAHA MAJESTYS, HONDA ZOOMERX, HONDA PCX125, HONDA PCX125 E:HEV, HONDA PCX125 Hybrid, HONDA PCX150, HONDA PCX160, HONDA CROSSCUB110, HONDA glom, HONDA MONKEY125, HONDA CB125R, HONDA CBR125R, HONDA CB250R, KAWASAKI Z125-PRO, HONDA DAX125, HONDA CT125CT110 HUNTER CUB, HONDA CL250
For CL250
Side Back on CL250
Because it is installed
Master Cylinder in Kochira
Type's installation on the
Helmet holder.
View detail
Tighter than expected.
I usually use SHOEI'sSize as Spec.
I checked on the Net and it says to choose one size up, but two sizes up may be fine. Well, everyone's head shape is different, so this is just for reference!
View detail
Could not be used for X-ROAD II.
This is not Webig's fault, but we tried to install this on our X-ROAD II, but there was no space to insert it, so we could not install it.
The package says it is also compatible with II, but the product labeling is incorrect to begin with.
View detail