Reviews
I bought it by model.
The size of the part that goes into the Head did not fit and could not be worked. I will probably process it and use it in the future, but I was a little disappointed. View detail
lacking in stability
It lifts up, but while lifting it up, it shifted forward and fell off.
I'm glad I didn't remove the Tire.
I replaced it with a higher one to be raised by the same Manufacturer's Stem.
Maybe I was not using it properly, but I didn't understand it because it was not explained in detail.
Maybe people without knowledge should not use it.
View detail
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
Not suitable for REBEL 1100
Instruction Manual is unfriendly and difficult to understand.
The receiver is not stable due to rubber.
Not suitable for heavy motorcycles.
I almost knocked it over.
View detail
damage
As you can see in the photo, the spring and functioning part of the component was damaged from the start.
I assume it is fabricated by cutting from a board.
If it is to be used as a spring, I think it needs to be heat-treated, but I guess it hasn't been.
There are welding areas nearby, so the heat from the welding may have an effect.
I think it's a product with a high breakage rate.
View detail
Defective item
When I looked at the product sent to me, the spring part was damaged as shown in the picture.
I assume the parts were cut from sheet metal.
If they were to function as springs, they would need to be heat-treated or something, but I guess they haven't done that.
The heat from the welds may have an effect, and I think the product has a high defect rate.
As for DAYTONA's STAND, the front stand has recently been voluntarily recalled.
I don't think they are made in-house, but as long as they are sold, DAYTONA needs to take responsibility for quality control.
View detail
Fits: HONDA MONKEY, HONDA APE, HONDA CT125CT110 HUNTER CUB, HONDA XRMOTARD, HONDA CHALY, HONDA DAX
Rear Maintenance Stand NORMAL
Rear Maintenance Stand NORMAL
I could not use it on my Grom JC92. The description reads like it would be compatible with NORMAL, though.
View detail
Triangle section is long and Motorcycle is not slanted.
Because the Triangle section is long, the Motorcycle is not slanted and will fall to the opposite side when the wind blows.
It is completely useless for both 18-inches and 19-inchesTire Racer.
I had to repurchase another product.
The Triangle seems to be about 1cm longer than the normal one that was repurchased.
View detail
It's a very good idea…
I bought this because I was worried about it coming off when I lifted up in the V by myself.
Since the Hook and the receiver are fixed, the sense of security is perfect, but the moment I lifted up, it was torn off.
Did I use it incorrectly?
But I understood how it works, so I bought a slightly thicker Rubber Band at 100 yen and wrapped it so that it would be fixed in the same way.Rubber Band is cheap even if it breaks, so I started using Rubber Band after that.
View detail
Garbage
I am Garbage.
The weld of the bar on the Screw part of the pedestal was tilted.
I managed to fix it with a Rubber Hammer, but I almost knocked over the Motorcycle! 。
The Damper also has a narrow range of effect and there is a shock when lowering the Motorcycle.
BootsSTAND and the welding of a good UNIT product is really inaccurate.
I should have bought the DRC honestly.
I will never buy a product made by unit again.
View detail
It cracks easily.
The SIDE pillars are strong enough, but the top panel is not strong enough.
I put my CRF450R on it twice and the top panel cracked.
Once it is cracked, you can't use it because it will shake the car body if you put it as it is.
I didn't put it on with a bang, but the top panel is plastic, so it's weak.
View detail
Not suitable for heavy vehicles and vehicles with large tire contact area.
* The video is a recent driving scene with my car FZr1000 3GM5.
[How is it used?
Cleaning and maintenance of wheel.
Was the one you received as per Image?
It was as per Image.
How was your experience with it?
As shown in the title, it is not suitable for heavy vehicles and vehicles with large ground contact area of tire.
[Points to note]
Even if you use it, I think it is up to 250cc class weight car body.
How did it compare to other products?
Chain lubrication, etc., is not necessary for a heavy body. Swingarm Lift Stand is better to use.
It can only be used for cleaning the wheel.
Other items that would be helpful
Installation Point or hang/It is better to lay a square of about 3 cm in STAND.
Items to buy together/Square timber.
Opinions and requests to Manufacturer/It should be indicated that it is difficult to use for chain lubrication of the rear wheel.
View detail
welding failure
I have welding quality control qualification WES. There are two defective weld pits, and it is painted without repair. The company name and "made in Japan" are written proudly. I wonder if they are not ashamed. View detail
easy
Used for ZrX1200R.
Shaft bent easily.
Disappointing
View detail
It broke on the first try
It's a cantilevered vehicle with 230k miles on it, and it broke on the first lift up
I was worried that the shaft is too thin to be threaded through, but it was no good
I bought it after seeing a review of my use of cantilevered and 270 pounds Was it bad?
View detail
It's hard to know what kind of car it's for
I bought a body and V receiver for maintenance on my CB650F
After purchasing it, I noticed that the body of the car does not have the for Swing ArmHook mounting screws
I didn't check myself enough, so I gave up
I have now purchased the L-Shaped Receptor
So, here's the problem again..
Use for 400 CC or less on the product you received in the mail It says
Then I think there should be an explanation to the L-Shaped Receptor before ordering! But what do you think? I bought it with high expectations because of the good reviews from everyone on Maintenance StandBody! But I'm disappointed 。 It's a shame that I can't send it through WeBike's exchange or contact page, no matter how many times I enter the information
sad 。 I think it would be better if you considered a more detailed response
View detail
Oh, no
I've written an impresario before, but I'll add to it 。 The lock lever at the bottom broke off while I was using the Motorcycle It's hard to lift, and it breaks in a flash, so this is a useless STAND! I've already arranged for a new STAND, but this is not the way to go when it's so expensive I will never buy anything from this manufacturer again View detail
distress
RearTire uses Racing Stand
I bought it using only the front tire?
I tried to use it, but the frame moves! Let's go! Straighten up!
The Tire spins more heavily than you might expect
Well, I bought it for a wash-for-vehicle, so...!
Quantity of Roller:Pair (for Left and Right) to prevent flooding with Grease
View detail
Fits: KAWASAKI Z1000 (water-cooled), KAWASAKI Z1000 (water-cooled) SX 11
precision defective product
Although delivered in a semi-finished state, we provide an instruction manual for everything from assembly to use There is no need to assemble it with the help of images You can find out how to use it by watching youtube etc However, in my case, it seems to have been hit by a defective product, and it is impossible to fix it to the car body The distance between one of the two insertion points was slightly insufficient to fit the other Because of use after a period of time has elapsed since delivery, the return of the product is also hopeless? Later, it disassembles and the Attachment position is scheduled to be corrected
To install to Z1000, pull out the bolt of the frame that is stuck in from the Left Put it back in from the Right and tighten it up with the Car Both SidesAttachment You can find out which Bolt is which in the youtube video
View detail
Dissatisfied
I am on a dTRACKER.
I bought it because it was cheap at Sale, but it looks like Large texture, and if I lift it up I will not even get my feet even on my hands. It is very inconvenient..
I can not lift with a force that is half-baked.
View detail
It is not usable
When using with GSX 1300 R HAYABUSA, Shaft is twisted by one shot. I bought another one but another one broke up with one shot.
When I talked about the situation via dealership "How to use" is bad
We also use GSX 1300 R HAYABUSA for explanation of how to use it, and we used it by using Axle Shaft for freeing a single finger, but we used it, but it is useless.
Considering the correspondence of Manufacturer, it is one of items that I can not absolutely buy.
View detail