Reviews
Reliable Brand
Purchased due to the addition of a Large Motorcycle.
We use Chinese STAND for 125 and 400 Class Motorcycles and this one for Large Motorcycles.
With Chinese STAND, the STANDBODY is distorted by the weight of the car body when it is lifted up, but this product can be lifted up stably without any problem at all.
If I had to make a request, I would say that protective parts should be attached to the pipe that touches the ground when lifting up, otherwise the STAND will become wound wound.
View detail
Easy to use
The rear wheels can be used without difficulty, but the front wheels cannot be used. The front wheels are gradually shifting, perhaps because they are stuck in place. View detail
I can't give it to you without it. It is a must buy!
I bought this Option to use the Jay Trip , Low Roller stand (item #:JT-1052QR).
"V-receiver, 2." They say.
To begin with, I did not purchase STAND out of necessity, but I purchased YOSHIMURA's Rear Stand Bracket Set for VSTROM250SX. (M8) I had been putting on the Option (Option 1) for the time being, so I bought this Option because I had seen it being used with the Jig Sur which is almost the same as the Option (Option 2) and I thought it would be good.
As expected, it worked properly.
However, if you don't use it well, the red rubber part on the end may come off, so it seems that you need to get used to it.
I am a novice when it comes to STAND for RoadMachine, so I will do my best to familiarize myself!
View detail
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
It's tough to go it alone.
If two people do it together, there is plenty of room, but alone it is quite scary.
If you have a Rear Carrier with Grab Bar, you may be able to do it by yourself, but it is very difficult because the REBEL is low and there is no part to grab on the Rear side.
I did it with two people at first to make sure I could do it, and then I tried it alone, but I almost beat him.
I think it would be wrong to object to the fact that it cannot be done by one person, since the Manufacturer recommends a two-person operation in the first place.
Motorcycle maintenance is basically a one-person job, so I felt like Minus in that I had to get help every time!
View detail
Fits: HONDA CB1300SF, Others Only available for vehicles with Quantity:2pc under frame.
UnderFrame Stand
To OH the steering stem of RZ, we fixed it with this product and worked on it.
It would be nice if the height could be raised a little more.
View detail
Easy to insert into Fork
When inserting the STAND into the front fork hole, the STAND tip bracket is inserted at an angle,
It is a little hard to get into the holes. Once it is up, it is fixed perfectly, but it takes a lot of time to insert it into the two Fork holes.
View detail
The product is good, but..,
The quality of the product is very good, as it is made in Japan. However, the contents of the package, especially the tires and other components, smelled like cigarettes and filled the storage room. It is a pity because the product is so good. View detail
better than nothing
The product will Gap depending on where it is placed. At that time, the RUBBER feet on the back will come off.
The bank angle is quite high, so even if you think you have placed it straight, it will gap.
View detail
good quality
Purchased as an addition to the company's Roller stand.
I don't have to tell you about the fit and consistency. I have used it without any complaints.
However, it seems that a protruding part has been added, but I have no idea what this is for...if anyone knows, please let me know.
View detail
Combination with SNIPER
I purchased the SNIPER Racing Stand Hook for my 2019 ZX-10RR.
STAND-UP has also become easier.
View detail
For Chain cleaning and lubrication
Rear wheel:Even if it is placed in the middle, it gapes due to the angle of the Side Stand, and the Chain side is difficult to work on because it is angled too much.
Front wheel:Handlebar is not recommended for use by one person, as it will break off and definitely Gap.
If I could get on it, I managed to turn the Tire with one hand.
View detail
For domestic cars, the included color is sufficient.
If it is to be used on a domestic car, I think the included colors will cover it.
There is a Bolt for fixing on the STAND side, but there is no Screw hole on the Adapter, so it is easy to come off.
View detail
Questionable quality inspection of products
I received it ahead of schedule, but when I was setting it up for installation to fit my Motorcycle's size,
The Clamp's corner Pipe was not penetrating the ArmHolder's insertion hole (One Side).
I had no choice but to use a slotted screwdriver as a chisel to remove the BALI.
DAYTONA, please inspect your products carefully.
View detail
How about one for Garage?
I purchased this product for the first time for Chain Maintenance.
I was nervous when I put it up for the first time, but Quantity was there without a hitch!:Set is ready.
It is so convenient that I wish I had introduced it sooner.
I am satisfied with the quality of the product, but I have one point,
The hook part was bare gold and it looked like it might scratch the Swing Arm,
I covered it with Fuel Hose, which happened to be available.
Other companies' MAJOR products have already taken countermeasures in this area, so please check this when purchasing.
View detail
I'm not sure when it was lost.
I bought it because one of the four was gone and the other was cracking.
It explains that double-sided tape makes it harder to remove.
If so, I wish they would put it on from the beginning.
It was a hassle to put it on, so I used Vinyl Tape to prevent it from coming off.
View detail
Chain Cleaning and Lubrication
I put the rear wheel on the Maintenance Roller Stand and cleaned the Chain, but the Tire was heavier than expected and a little difficult to turn. I am a beginner, but I managed to do it. View detail
diversion
It was installed in the STAND of J-TRIP.
There was a rattle, so we eliminated the rattle with an appropriate Bracket.
View detail
Fits: SUZUKI V STROM 1050, SUZUKI V STROM 650
Some parts are pricey, but no problem.
Chain and Wheel cleaning was inconvenient and price.
Buy this one which is Reasonable.
Assembly is required, but the height can be adjusted without any problem. The Hook and the Adapter for direct use of the Swing Arm are included from the start. I purchased a ZETA Swingarm Spool at the same time and used the Hook for its stability.
When using the STAND, hang the vehicle straight with the front brake applied →STAND on the Hook →STAND rearward tip down, and you are done.
Note that there is no Cover on the Hook, so I made a mistake at first and damaged the Swing Arm as much as I could….
There is no wobble, and the feel is satisfactory. Above all, I am satisfied with the maintenance performance of the Large width up.
View detail
Needs a little work.
The inner diameter of the Adapter seemed to be a little small, so I could not install it, and since I did not want to cut down the STANDBODY side, I used a Leutor to cut down the inner diameter of the Adapter I purchased this time so that it would be large enough to fit. Although I was disappointed with the product itself, I am glad that the Adapter only was sold, even if it requires a little modification, because without it, I could not STAND-UP safely. View detail
A little processing was required.
The inner diameter of the Adapter seemed to be a little small, so I could not install it, and since I did not want to cut down the STANDBODY side, I used a Leutor to cut down the inner diameter of the Adapter I purchased this time so that it would be large enough to fit. Although I was disappointed with the product itself, I am glad that the Adapter only was sold, even if it requires a little modification, because without it, I could not STAND-UP safely. View detail