Reviews
A must-have for maintenance
YAMAHA I purchased Y’S GEARService manual for maintenance and restore of FZX750.
I think YAMAHA's service manuals are conscientiously priced, since the ones from Japan and other manufacturers, especially H cars, are very expensive.
(Supplemental editions are purchased separately as there are slight differences depending on the year)
I thought the Manual was no longer available since it is an old vehicle, but thankfully it is still published.
This Manual is easy to understand because it uses photographs rather than graphics due to the content at the time of its release!
However, since the unit of torque for tightening Bolt and Nut is expressed in ?-m, it is necessary to replace the unit with N-m.
If you do your own maintenance, a service manual for your car is a must.
*Used Situation is the usual way of riding. The work skill is set as intermediate because the degree of difficulty varies depending on the content of the maintenance.
View detail
All but Model 2AK0 are required to supplement the complete version.
I purchased this as a supplement to the complete edition because I need it for maintenance and restore of my YAMAHA FZX750.
(You can't use the supplemental version if you don't have the complete version.)
This supplement is a supplement to Model 3XF1-5.
My FZX750 was probably a learner's car? The model number is 3XF2, but the VIN number is not listed in the manufacturer's site.
The battery is also specified by the manufacturer as YB14L-A2, but YTX9-BS, a sealed type, is installed.
The electrical system is a weak point, so it is thought that the previous owner improved the entire regulator.
My FZX750 has had a strange fate. My FZX750 has had a strange fate, which is why a supplemental version was necessary.
The service manuals of the time were very detailed, listing the bearing numbers for each part, the Horn, StartingMotor, generator standards, and even the manufacturer.
View detail
YAMAHA FZX750, final 3XF5 supplement.
I purchased this as a supplement to the complete edition because I need it for maintenance and restore of my YAMAHA FZX750.
(You can't use the supplemental version if you don't have the complete version.)
This supplemental version is a supplement to Model 3XF5.
My FZX750 is model 3XF2, and I purchased it after determining that the contents of the final 3XF5 were not covered by the complete and supplemental 3XF1-5 editions.
I know it is a minute difference, but it is better to be prepared.
View detail
I'm still glad I bought it!
I think the best value is the ability to manage Torque. View detail
More stable than expected.
Used for Grom JC75.
It was used as is with no problems.
I am happy with the stability and it is more solid than I expected, but I still have to glue the Grip by myself.
I like the look of the product and look forward to seeing it in the future.
View detail
Not available for 2023GROM
I purchased this product because it was indicated that it could be installed on a 2023 GROM, but the type of the Air Cleaner Box has changed from the previous model and it cannot be installed immediately.
There is an intake on the Engine side at the far end, which is inaccessible. It might be possible to install the unit if all the ducts were loosened and removed, but I decided not to do so because it would take too much time.
It was a waste of time, so I installed it in the intake of the box in front of the Air Filter.
Does it seem to be effective from where it is installed? Or not?
I would like to believe that there is.
View detail
It can be used properly.
The texture does not feel cheap. It's also strong and stable.
When used in conjunction with the Ladder rail and placed on the Transporter, it can also be used properly as a step ladder.
STANDDecal is also easy to customize because of the variety.
View detail
I can really help. It is safe and secure.
It is safe because Hook does not move.
We recommend that you take a look at Jtrip's Channel on YouTube for a video showing how to use it.
Work is safe and secure.
View detail
A necessity for maintenance
It is a must-have if you want to keep your Motorcycle for a long time. It is expensive, but it contains a lot of necessary information and is indispensable if you want to keep your Motorcycle large. View detail
Wouldn't this be the perfect maintenanceSTAND for Middle motorcycle!
I am satisfied with the stability of the vehicle when using the rear stand, the lightness when lifting up, and the price. I was thinking of replacing the tires by myself in the future, and I am also hoping to expand the range of maintenance of other parts. (The Z650RS weighs 188kg *Rear Carrier would be better) It only requires a little weight by hand. It is very convenient because I used to do one side lift up with a piece of wood.
Comparisons were made with Company S, Company A, and Company J. As a result, we decided on DAYTONA. As the reason for the selection, I considered that the structure of the most load-bearing part is Square Type, which seems to be sturdy, and that it is superior in terms of comparative cost. Also, the fact that the product introduction image is of RS was a deciding factor. The other 3 companies are all sold separately, and S and A are a little cheaper than DAYTONA, but there were some comments that the stability of the frame is not so good. I have not actually used them, so I am not sure.
The Stand Hook holder is specified to have a diameter of 14 to 18mm. If the diameter is larger than this, it will not fit in the attachment. Also, it takes a little getting used to inserting the Attachment.
The only drawback is that the latch of the U-shaped attachment is too thin and I am not sure if it is durable. I am not sure if it is durable or not. I don't know because I haven't used it yet. However, spare parts are available, so there is no need to worry. (This is not a problem for those who can weld.)
J company claimed that the handlebar should be set to "Left" and "Up" when the brake is "STAND-UP", while DAYTONA company claimed that the handlebar should be set to "Straight". I am not sure of the difference, but I found that the fixation of the hook of the front brake at the time of OthersLift up was the same in all companies. I hope this is of some help.
View detail
It's convenient, small and good.
I am currently using the center front stand.
The disadvantage is that it is bulky, heavy, and requires an adapter to be carried.
There is a risk of losing the adapter, so I ordered a stand that hangs on the fork.
First of all, it is very light and has little space. It's easy.
Very satisfied. I think I will only use this from now on. -------------------------------------------------- -------- I am currently using the center front stand. The disadvantage is that it is bulky and heavy and requires carrying an adapter. There is a risk of losing the adapter... so I ordered a stand that hangs on the fork. First of all, it is very light and has little space. It's easy. Very satisfied. I think I will only use this from now on. Powered by Google Translator
View detail
Fits: YAMAHA XG250 TRICKER, YAMAHA XG250 TRICKER
Service manuals that are fun to look at
Items is essential to know every detail about your car, isn't it? I am only a hobbyist and a skilled car builder, but I feel happy just reading these items because of my love for machines and motor cycles. Of course, I want to make my car last longer, but I also don't want to cause accidents with my own troublemaking. Nowadays, we can look up anything on the Net, but having a book at hand gives me an indescribable feeling of happiness and satisfaction. I recommend this book to anyone who understands it! View detail
Almost perfect except for the price.
The front and rear stands seem to be the best in a certain manufacturer, but this product is sufficient for cleaning and simple maintenance at the Amateur level.
However, the price could be lower, so the rating was not a perfect score.
View detail
DAYTONAfor Repair
I bought this one because I cry when I drop it.
Used for thruxtonrs.
The oval-shaped swing arm has a shallow hook.
If this is not possible, use a Y-shape.
View detail
useless
Purchased for Spoke maintenance. Conclusion:It can't be used. First of all, I can't use it with Harley because I can't get over the bumps. It was faster to use Jack. View detail
It's good to have it
All Data is here.
When something is broken, something is modified, or some parts are added, it is possible to isolate from electrical drawings, tightening torque, and error codes, and to perform pass/fail tests for each part.
If you do your own maintenance, there is a LARGE difference between having it and not having it.
Service manual for YZF-R1 RN20 4C8 is very expensive but I am glad I bought it.
View detail
A must-have for Overhaul
I know the price is high since it is a new OEM product, but I would have expected more detailed instructions on how to remove and assemble it.
The essentials, tightening Torque, and limits of consumables are detailed and useful.
Is it difficult for a layman to use just the Service manual without knowledge of maintenance?
View detail
Daytona spool nut
Fits perfectly! View detail
I am glad that there is a Repair item since the item will deteriorate!
I bought for Repair because it has been ripped over time and the Rubber at the tip of the V-receptacle has been coming off every time I apply STAND.
I am glad that there is a Repair item, as these items deteriorate.
Double-sided tape makes it harder to pull out." I also put up Double-sided Tape because of the proviso that it was a good idea.
Since it is Rubber, deterioration is inevitable.
Hopefully this won't take...
View detail
I bought it by model.
The size of the part that goes into the Head did not fit and could not be worked. I will probably process it and use it in the future, but I was a little disappointed. View detail