Reviews
Easy to use
The rear wheels can be used without difficulty, but the front wheels cannot be used. The front wheels are gradually shifting, perhaps because they are stuck in place. View detail
Fits: HONDA Ape 50, HONDA Ape 100, HONDA Ape 50, HONDA Ape 100
The APE can be found at ・・・・
I purchased this carburetor and installed it in order to prevent dust from being sucked into the carburetor while driving on the street, but the intake resistance was much greater than I had imagined. In addition, the carburetor protrudes to the Right on the APE, so the Rubber that stops the Net when the carburetor hits the thigh while driving is not able to be used.
Gap and before I knew it, Net and Sponge were gone. Now I am using Funnel with JAM's 3D Air Filter (Right Side Cover needs to be removed or partially cut).
View detail
RIDEX has reached the 20-volume Large table!
At last, RIDEX has reached the 20-volume Large table!
congratulations
The LineUp of Machines appearing in this issue is as follows,
HondaCRF250.Harley883R, RZ50.RZ250, HondaGROM, GSX-R1000R, etc,
Unusually, it is not one side full of old cars, and Genre is not biased,
I liked reading it because it was an even mix.
If you could write in such a way that a wide range of Motorcycle riders can relate to it,
I wouldn't mind buying it again, what a great idea!
Well, my Motorcycle has never appeared in this comic.
I hope to see it published in the future, hopefully by volume 50 or so.
View detail
Volume 19 of RIDEX.
In Motorcycle Manga, this is volume 19 of the well-known RIDEX.
Because I have already purchased it as Collection due to inertia,
I won't go into detail about the quality of the content,
The Machines in this volume are,
GSX1100S KATANAS, MACH, SR400, ZEPHYR, HondaDAX and,
They are all Motorcycles, which appear frequently in previous volumes, and which this author likes Large.
To be honest, though, it's all the same old rutty, full of stories that I've read before,
The pictures are beautiful, so if you consider that you could buy a Motorcycle color Illustration collection for about 1000 yen,
Cost performance is not too bad and not too much of a headache.
That's about it
View detail
I can't give it to you without it. It is a must buy!
I bought this Option to use the Jay Trip , Low Roller stand (item #:JT-1052QR).
"V-receiver, 2." They say.
To begin with, I did not purchase STAND out of necessity, but I purchased YOSHIMURA's Rear Stand Bracket Set for VSTROM250SX. (M8) I had been putting on the Option (Option 1) for the time being, so I bought this Option because I had seen it being used with the Jig Sur which is almost the same as the Option (Option 2) and I thought it would be good.
As expected, it worked properly.
However, if you don't use it well, the red rubber part on the end may come off, so it seems that you need to get used to it.
I am a novice when it comes to STAND for RoadMachine, so I will do my best to familiarize myself!
View detail
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
It's tough to go it alone.
If two people do it together, there is plenty of room, but alone it is quite scary.
If you have a Rear Carrier with Grab Bar, you may be able to do it by yourself, but it is very difficult because the REBEL is low and there is no part to grab on the Rear side.
I did it with two people at first to make sure I could do it, and then I tried it alone, but I almost beat him.
I think it would be wrong to object to the fact that it cannot be done by one person, since the Manufacturer recommends a two-person operation in the first place.
Motorcycle maintenance is basically a one-person job, so I felt like Minus in that I had to get help every time!
View detail
It didn't work. (My mistake)
My AF24TACT with AF34LIVE DIO carburetor installed. (This product) The diameter of the lens was just a little too small. The diameter did not fit and I could not install it even though I tried to modify it and force it to fit. It is a pity because it is very cool. It is my mistake that I bought it without checking it carefully. View detail
Fits: HONDA CB1300SF, Others Only available for vehicles with Quantity:2pc under frame.
UnderFrame Stand
To OH the steering stem of RZ, we fixed it with this product and worked on it.
It would be nice if the height could be raised a little more.
View detail
Easy to insert into Fork
When inserting the STAND into the front fork hole, the STAND tip bracket is inserted at an angle,
It is a little hard to get into the holes. Once it is up, it is fixed perfectly, but it takes a lot of time to insert it into the two Fork holes.
View detail
The product is good, but..,
The quality of the product is very good, as it is made in Japan. However, the contents of the package, especially the tires and other components, smelled like cigarettes and filled the storage room. It is a pity because the product is so good. View detail
better than nothing
The product will Gap depending on where it is placed. At that time, the RUBBER feet on the back will come off.
The bank angle is quite high, so even if you think you have placed it straight, it will gap.
View detail
Maintenance essentials
Maintenance necessities including Torque management
I have been stingy and gathered information on the web etc., but considering the accuracy of the information and the time involved, it is better to purchase.
I should have bought it earlier.
View detail
good quality
Purchased as an addition to the company's Roller stand.
I don't have to tell you about the fit and consistency. I have used it without any complaints.
However, it seems that a protruding part has been added, but I have no idea what this is for...if anyone knows, please let me know.
View detail
Combination with SNIPER
I purchased the SNIPER Racing Stand Hook for my 2019 ZX-10RR.
STAND-UP has also become easier.
View detail
For Chain cleaning and lubrication
Rear wheel:Even if it is placed in the middle, it gapes due to the angle of the Side Stand, and the Chain side is difficult to work on because it is angled too much.
Front wheel:Handlebar is not recommended for use by one person, as it will break off and definitely Gap.
If I could get on it, I managed to turn the Tire with one hand.
View detail
For domestic cars, the included color is sufficient.
If it is to be used on a domestic car, I think the included colors will cover it.
There is a Bolt for fixing on the STAND side, but there is no Screw hole on the Adapter, so it is easy to come off.
View detail
Questionable quality inspection of products
I received it ahead of schedule, but when I was setting it up for installation to fit my Motorcycle's size,
The Clamp's corner Pipe was not penetrating the ArmHolder's insertion hole (One Side).
I had no choice but to use a slotted screwdriver as a chisel to remove the BALI.
DAYTONA, please inspect your products carefully.
View detail
How about one for Garage?
I purchased this product for the first time for Chain Maintenance.
I was nervous when I put it up for the first time, but Quantity was there without a hitch!:Set is ready.
It is so convenient that I wish I had introduced it sooner.
I am satisfied with the quality of the product, but I have one point,
The hook part was bare gold and it looked like it might scratch the Swing Arm,
I covered it with Fuel Hose, which happened to be available.
Other companies' MAJOR products have already taken countermeasures in this area, so please check this when purchasing.
View detail
I'm not sure when it was lost.
I bought it because one of the four was gone and the other was cracking.
It explains that double-sided tape makes it harder to remove.
If so, I wish they would put it on from the beginning.
It was a hassle to put it on, so I used Vinyl Tape to prevent it from coming off.
View detail
Chain Cleaning and Lubrication
I put the rear wheel on the Maintenance Roller Stand and cleaned the Chain, but the Tire was heavier than expected and a little difficult to turn. I am a beginner, but I managed to do it. View detail