Reviews
Maintenance essentials
Purchased to do my own maintenance.
It's a necessity
It's fun just to read about it.
View detail
Small Stand Hook.
I installed this Stand Hook on my SC59 CBR1000RR, and I have noticed that if the Stand Hook is long enough, the whole Swing Arm weld often flies off when the bike falls over. This Stand Hook is very small and I think it will minimize the damage when it falls over. I slip down once after installing the Stand Hook and the Stand Hook was not damaged. I also use the Rear Stand made by the same company, but the Stand Hook is not so small that it is difficult to lift up, and I think it is very easy to use. View detail
Heavy objects are easily lifted
There are many products out there, but I chose J-TRIP. It is already easy. However, L-Shaped Receptor and Small Motorcycle seem to be incompatible, so I purchased a V-shaped Receptor separately and am now using it. View detail
For cleaning front wheel
Purchased for cleaning Front wheel, not used for Rear as there is a Center Stand.
After applying the Center Stand, float the Front a little and apply this STAND to the Quantity.:Set.
The non-slip Rubber is a little difficult to insert because it is more effective than expected.
It looks good for use according to the Instruction Manual.
By idling the front wheel, cleaning is much easier.
View detail
Chain Cleaning and Lubrication
I put the rear wheel on the Maintenance Roller Stand and cleaned the Chain, but the Tire was heavier than expected and a little difficult to turn. I am a beginner, but I managed to do it. View detail
![Service Manual [Supplemental Version]](https://img.webike-cdn.net/catalogue/images/111384/service_manual_yamaha_TS.jpg)
Supplement for late model
It is a Supplement to the Second Type Model of XJR400R.
Each adjustment point corresponds to a later period.
The vehicle I purchased was a MODEL with Immobilizer, so I wanted to check the Wiring diagram around the Front and to check the detailed differences.
The information I wanted to know was well described, so I could check it while performing maintenance.
View detail
![[Repair Parts] U Type Clamp Attachment](https://img.webike-cdn.net/catalogue/images/109969/29982_TS.jpg)
diversion
It was installed in the STAND of J-TRIP.
There was a rattle, so we eliminated the rattle with an appropriate Bracket.
View detail
Rugged STAND
It is BoxSTAND, Off-road motorcycle owners should have at least one.
I think it would be easier to put the Block under the Side Stand, tilt it to Left, and then put it in from the body Right.
BoxSTAND is so sturdy that once you buy one, it will last you a lifetime.
View detail
To maintain your car properly
You will get detailed and correct information.
However, in my case, I bought it in the sense of Collection.
View detail
Very lightweight
This is a very lightweight STAND. Originally, we were using a STAND made by another company, but it was heavy and a little inconvenient when carrying it or loading it on the transporter. The Battle factory STAND we purchased this time is very lightweight and can be carried easily with one hand. The feel of the STAND is not a particular problem, but it is a little less rigid than the steel ones made by other companies, but I thought that was a trade-off with the lightness.:I like it because it is Stainless Steel and looks very Parenthesis. The bosses are set up differently for each car model, so you should be aware of that when purchasing. I highly recommend this product and I am very satisfied with it. View detail
Required for full-scale maintenance
I purchased this product for servicing my XJR400R.
It could have been used, but it's as good as used. (Rather, used ones are more expensive.) I chose the new one because of the price.
The complete edition contains details from ServiceData to maintenance procedures and Wiring diagrams.
Although there are more videos and blogs these days, they often have the wrong things or do not give the information we want.
I think it is essential for those who do their own maintenance to ensure that the correct procedures are followed.
View detail
J-TRIPShort low ler Rear stand
I purchased this for my MT-09.
We considered cheaper companies A and D, but after reading your review, we decided to purchase JT-RIP.
Because there is no room in the length of Garage, we decided to use Short. It is also stable enough.
It helps with maintenance, but if it were cheaper, I would have no complaints.
View detail
Fits: HONDA CB1300SF, Others Only available for vehicles with Quantity:2pc under frame.
It is useful for maintenance.
I am using it for maintenance of CB750four. I have to remove the Center Stand because it is wearing the assembly tube. Before I purchased this product, I had a hard time adjusting the chain, changing tires, etc., fighting the fear of tipping over. Now I can do maintenance around Front and Rear by changing the place to hang the STAND. （The only thing is that it is hard for old people to bend down and rotate the jack with the pin spanner, although it is unavoidable due to the structure. View detail
Looks strong
If you order this Check your hooks diameter first, Looks strong and When lift up, it's solid without shaking. Don't forget to check the internal diameter size of the swing arm's hook and then jive it out of the two models from j-trip View detail
Is Ideas a good but subtle product?
I could only find an article advertising Off1etc., so I bought it as a human sacrifice (purchased via the Rakuten side of Webike).
Ideas are good, but anyway ”heavy”. it is certainly easier than putting it on the MXSTAND, but it is too heavy compared to the Ethos STANDetc. which I like and have two of, and NG.
There are two points
(1) Color on iron:Gray paint.
I thought it might be aluminum, judging from the color in the photo, but it turned out to be iron. The body itself is heavy. Also, the paint is peeling off and rust is showing on the operating parts. Quality-wise, it is the same as Unit's various products.
(2) Regarding functionality
1. Front tire rides on the tip and the STAND section is slightly raised.
2. Step on Lever and lift
The lift is raised by the 2 actions of 1 and 2, but since the fixed point under the frame is determined by the position of the front tire in Action 1, it is not possible to fine-tune the lifting position back and forth.
With Enduro racer, even at 1G, the suspension contracts quite a bit and the minimum ground clearance is low, so it is set up on the Under Guard quite a bit in front and the first adjustment does not work.
The Beta RR2T was not able to lift the rear wheel enough, because the fulcrum was slightly forward of the horizontal point. It was a halfway feeling. I haven't tried it, but I think CRF250R might be a better point for my Motorcycle, and YZ125 might be a little bit too sensitive position.
I'm not sure what kind of car you are talking about. I am wondering what type of car was designed for what type of car.
I bought it for my tiger car (Beta Evo), so it seems to fit in a relatively good position since the body is light and the wheelbase is short. So it is a product that can be used...
I honestly don't think I would recommend it to everyone.
Maybe it's good for going for a ride and using it outside? But it's steel and it's going to rust soon...
Might be useful in Race like JEC where matte is laid down.
View detail
A constantly evolving Manufacturer
from before I've never done this before. is used
I have repurchased Matte Black from STAND, a collaboration between Nankai Parts and J-Trip!
When I received it in my hand and compared it with
Plating mirror surface was missing.
It looks cloudy like Uniqlo plating.
Or is there a secret that makes it rustproof?
The area of the Rubber on the receiver is now larger.
I think you can tell from the pictures.
Constantly evolving Manufacturer J-Trip
(Incidentally, DAYTONA part number 25298 has a 20mm Adapter on the front stand.
J-Trip is φ15, 17, 19, 22, 24, 27
DAYTONA is φ15.5, 18, 20, 22, 24, 27
Yes, it is subtly Gap!
I want to make it as close to the Stem hole as possible, so if you see this review, please give it a try.
Just 20mm is delicious in XJR1300 and FZr1000, so older Yamaha models would be good!
View detail
Fits: SUZUKI V STROM 1050, SUZUKI V STROM 650
It was above my imagination.
I use it on my Z900RS. L-Type Arm hangs behind the Swing Arm for easy lift up.
If you are working alone, it is easier to work with a piece of wood under the Side Stand as it is close to parallel.
View detail
SV650 in '99 car.
As long as the width is positioned properly, the Swing Arm can be used perfectly without interference or rattling. View detail
Dream Service Manual
I was looking for this manual for long time and eventually decided to buy it. It is not cheap but a worthwhile. The manual in Japanese language but has lot of good photos of servicing bike. Good to have a copy View detail
Dream rear stand
Very well made rear stand. Easy to use. Unfortunately due to tight construction, rear wheel can't be turned while bike on stand. Otherwise I'm very happy with this product View detail