Reviews
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
It's tough to go it alone.
If two people do it together, there is plenty of room, but alone it is quite scary.
If you have a Rear Carrier with Grab Bar, you may be able to do it by yourself, but it is very difficult because the REBEL is low and there is no part to grab on the Rear side.
I did it with two people at first to make sure I could do it, and then I tried it alone, but I almost beat him.
I think it would be wrong to object to the fact that it cannot be done by one person, since the Manufacturer recommends a two-person operation in the first place.
Motorcycle maintenance is basically a one-person job, so I felt like Minus in that I had to get help every time!
View detail
Fits: HONDA CB1300SF, Others Only available for vehicles with Quantity:2pc under frame.
UnderFrame Stand
To OH the steering stem of RZ, we fixed it with this product and worked on it.
It would be nice if the height could be raised a little more.
View detail
better than nothing
The product will Gap depending on where it is placed. At that time, the RUBBER feet on the back will come off.
The bank angle is quite high, so even if you think you have placed it straight, it will gap.
View detail
For Chain cleaning and lubrication
Rear wheel:Even if it is placed in the middle, it gapes due to the angle of the Side Stand, and the Chain side is difficult to work on because it is angled too much.
Front wheel:Handlebar is not recommended for use by one person, as it will break off and definitely Gap.
If I could get on it, I managed to turn the Tire with one hand.
View detail
Questionable quality inspection of products
I received it ahead of schedule, but when I was setting it up for installation to fit my Motorcycle's size,
The Clamp's corner Pipe was not penetrating the ArmHolder's insertion hole (One Side).
I had no choice but to use a slotted screwdriver as a chisel to remove the BALI.
DAYTONA, please inspect your products carefully.
View detail
Chain Cleaning and Lubrication
I put the rear wheel on the Maintenance Roller Stand and cleaned the Chain, but the Tire was heavier than expected and a little difficult to turn. I am a beginner, but I managed to do it. View detail
![[Repair Parts] U Type Clamp Attachment](https://img.webike-cdn.net/catalogue/images/109969/29982_TS.jpg)
diversion
It was installed in the STAND of J-TRIP.
There was a rattle, so we eliminated the rattle with an appropriate Bracket.
View detail
Fits: SUZUKI V STROM 1050, SUZUKI V STROM 650
Some parts are pricey, but no problem.
Chain and Wheel cleaning was inconvenient and price.
Buy this one which is Reasonable.
Assembly is required, but the height can be adjusted without any problem. The Hook and the Adapter for direct use of the Swing Arm are included from the start. I purchased a ZETA Swingarm Spool at the same time and used the Hook for its stability.
When using the STAND, hang the vehicle straight with the front brake applied →STAND on the Hook →STAND rearward tip down, and you are done.
Note that there is no Cover on the Hook, so I made a mistake at first and damaged the Swing Arm as much as I could….
There is no wobble, and the feel is satisfactory. Above all, I am satisfied with the maintenance performance of the Large width up.
View detail
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
It also worked with the YamahaBOLT Shoulder Bag.
Although the only model that was compatible with this product was the Rebel, I thought that it might be effective for the BOLT Shoulder Bag since the Swing Arm is round. I bought it with the intention of becoming a human sacrifice. As a result, I bought it thinking that it would be useful for the BOLT Shoulder Bag, but the Brake Caliper is located under the Swing Arm, and the stubborn Exhaust Bracket is in the way. The BOLT Shoulder Bag, however, has the Brake Caliper under the Swing Arm, and the stubborn Exhaust Bracket is in the way and the position of the Bracket is fixed. The Front Brake Lock is an absolute necessity. View detail
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
DAYTONA
I'd like to see it built a little sturdier. View detail
easy to find a place to put things
It is small in size, so it is good to be able to place it in the right place. It can be used normally.
But if you have JTrip's Rear stand, that is more convenient in many ways.
View detail
Large Motorcycle can be used, but it's tough.
I used it on a Large Motorcycle, but I have the impression that it does not improve efficiency on the Front because the Roller comes off from the Guide while turning the Wheel. View detail
It takes more strength than you think to turn it.
I bought a similar Roller stand at a certain cheap tool store and it did not turn by hand at all.
I trusted Brand and bought this one.
It's a 900cc motorcycle, but it takes more power to turn the tire than I expected. It is much better than the thing of the cheap tool store, but ChainMaintenance is quite Large strange. It seems to be inevitable with this type.
If you have a place to store it, it's much better to buy a Maintenance Stand. It's for people who don't have storage space.
View detail
I want to make chain refueling easier since there is no main stand.
I'm not sure if it's because I'm not used to it or because it's too heavy to turn the tire. View detail
The slide is useless.
The non-slip surface on the back of the body comes off immediately. is coming off immediately.
Since it supports a heavy object, please make it more solid.
If the body is dislodged when it is placed on the Roller, the RollerBody will not remain stationary and the
If there is no non-slip surface, the genus Gold part rubs against the ground and scratches it.
I'm just going to do some Chain cleaning.
Would a Type that lifts the car body be better to work with?
I feel like I can work better when the wheels are turning.
This one is more stable, though.
View detail