Reviews
Fits: Others 200 series High aceDX standard Body
I'm glad I bought it
I bought this product to reduce the burden of moving.
There are no special precautions for installation as you just plug it in.
However, it may be easier to use the slide of the seat without it after installation because the thing itself is long.
I'm also worried about the durability of the inserts, as they are too tight and need to be moved unexpectedly when wearing the belt.
I have no complaints when using it, and my shoulders are quite comfortable since it is the same height as where the WindowSwitch system is on the Right hand side, etc.
View detail
Fits: Others High ace200 series (general)
Not a good fit feeling
I bought this because I wanted to use the rear gate as a point for the hanger.
I tried to use it as soon as I received it, but the shape didn't seem to fit.
If the Damper is overloaded, it will lose and come off.
It's a shame because I don't think I can use it with too much confidence.
View detail
Fixed Point increase
Purchased to increase the number of fixed points for Transporter.
Since it is an Exclusive Design, it was easy to install with Bolt On.
I'm not sure how durable it is, since I just bought it.
I think it will last for a while since it's made of only Gold materials.
View detail
If you use the Seat with it folded, tragedy awaits you.
As you can see, it is a product that can be attached to the legs of the second seat to add Tie DownHook.
It is important to note that the second seat is designed to be used with the seat out (ready to be used as a seat) and not folded.
It looks like you can use it folded up, but you can't because the seat itself floats when you try to pull it down with Tie Down.
I thought I could use it for a moment because the Seat that I was using in the folded state would not lift up easily, but if I continued driving, the Seat would lift up and the body of the car would fall down at the same time.
Of course, if you use it with Seat out, there is no problem.
However... I almost never use the RearSeat, so I always fold it up to increase the cargo capacity.
So, ignore the original usage and don't do it if it's true. Seat folded. I'm forced to use it in
The way I did it was to clamp the pipe in a position that was 90-degrees different from the correct position.
In this method, the pipe clamp is subjected to a great deal of force in the direction of rotation, and in the worst case, the clamp may cause the hook to rotate and the Tie Down to loosen.
It is completely misused and all at your own risk.
Seat. "Hard to float." In the worst case, there is a very high possibility that the motorcycle will float and fall over.
However, if you use the Belt MountHook High ace for 200 series (https://www.webike.net/sd/24635762/) to hang the bike from the top first, and then pull it downward, you can prevent the bike from falling over even in the worst case scenario.
I don't want my motorcycle to fall over or have an accident, so I use them together properly.
In addition, the clamp part of the product is quite a gorgeous material.:It's aluminum, and the surface is moist and polished as if it were Barrel polished, and it looks pretty good.
However, for some reason, the hooks are unusually tacky, and commercially available steel hooks are still used.
I don't think anything of it, because I'm in the camp where quality is good, but if you're looking for a luxurious interior, it might bother you.
View detail
The inner diameter of the color is cutts.
Purchased for Second seatBelt
Installation is easy, just remove the screw from the seat belt anchor and tighten it together with this part.
The pitch is very fine compared to the screw diameter, so if you try to put the screw in the slant, you will ruin the screw hole, but if you are not too clumsy, you can carefully put the screw in and it will be large and strong.
The first thing you should do is to screw in the screws by hand.
I thought, "Is this large enough? I thought so, but it's surprisingly large and strong, and the body side doesn't deform or the parts (3.0mm thick steel plate bent and punched out by PRESS) don't deform.
In the first place, it's not something that you have to jerk with all your might to pull the tie down, but rather something that supports the body of the car so that it doesn't fall down as it hangs from above.
No problems.
It doesn't get in the way during normal riding, and even if there is an accident, it is unlikely that the passenger will be harmed by this part.
It's also inexpensive (I don't want it to be expensive because of its cheap construction, but it's also reasonable because it's a bit of a hassle to try to make it yourself), so I don't think there's any harm in buying it.
The only weak point is that the vibration of the car makes it noisy and tinkly.
I have Anti-Vibration Rubber to prevent this from happening, but it still tinkles.
If you have a car that's silent or something, you'll probably notice it quite a bit.
So, before you put on the cover, it's a good idea to buy some dishwashing sponge at a 100-yen store, cut it into an appropriate size, and stick it in.
Well, I don't have to worry about it because I can just plug it in later.
If you don't want to do that, you can always use Tie Down and keep the tension on.
Also, whether it was the individual difference of the vehicle or the precision of the product, the inner diameter of the included Spacer was too small to pass through the Anchor bolt by hand.
The color of the Anchor bolt is Aluminum Cut-out, which seems to be highly accurate, so I think it might be caused by a thick coating of paint on the Anchor bolt, but I'm not sure.
The solution is not to try to install it straight away, but to hang it first using only the anchor bolt and collar.
This will press-fit the collar into the Bolt, and then it can be installed normally.
Note that if you make a mistake, the collar will be press-fitted and it will be very difficult to remove.
It's not something I'd use on a van van, but it's inexpensive, so don't hesitate to buy it when you need it.
View detail
It's super convenient to use it as a fall prevention device in the worst case scenario.
Purchased for front seatBelt.
Installation is easy, just remove the screw from the seat belt anchor and tighten it together with this part.
The pitch is very fine compared to the screw diameter, so if you try to put the screw in the slant, you will ruin the screw hole, but if you are not too clumsy, you can carefully put the screw in and it will be large and strong.
The first thing you should do is to screw in the screws by hand.
I thought, "Is this large enough? I thought so, but it's surprisingly large and strong, and the body side doesn't deform or the parts (3.0mm thick steel plate bent and punched out by PRESS) don't deform.
In the first place, it's not something that you have to jerk with all your might to pull the tie down, but rather something that supports the body of the car so that it doesn't fall down as it hangs from above.
No problems.
It doesn't get in the way during normal riding, and even if there is an accident, it is unlikely that the passenger will be harmed by this part.
It's also inexpensive (I don't want it to be expensive because of its cheap construction, but it's also reasonable because it's a bit of a hassle to try to make it yourself), so I don't think there's any harm in buying it.
The only weak point is that the vibration of the car makes it noisy and tinkly.
I have Anti-Vibration Rubber to prevent this from happening, but it still tinkles.
If you have a car that's silent or something, you'll probably notice it quite a bit.
So, before you put on the cover, it's a good idea to buy some dishwashing sponge at a 100-yen store, cut it into an appropriate size, and stick it in.
Well, I don't have to worry about it because I can just plug it in later.
If you don't want to do that, you can always use Tie Down and keep the tension on.
It's not something I'd use on a van van, but it's inexpensive, so don't hesitate to buy it when you need it.
View detail
It can be used normally
The Blinker relay broke and I used it to make a Wiring with Coupler to mount on the car body because the one I bought for Replacement did not have a wire or Coupler.
0.The 75sp wire is installed, the cover is cut at the height of the terminal face, and the Coupler is installed on the other side. 75sp wire is connected to the Blinker relay properly, and it seems not to fall off.
Cheap Electric Works PliersQuantity:I can't compare it to something like the one in Set, but the Crimping part is thicker and more solid.
You can buy just the right amount of this type of product, and more often than not, you'll have the opportunity to choose Emon for its quality and reliability.
View detail
Just fit
The Center console part has been stuck in my mind every time I ride it.
I always put my phone there, but when I stepped on the Brake a little too hard, it was ejected forward and I had to rummage around underneath at traffic lights… but the Non-slip mat solved the problem.
The size is just right! It is indeed a special product.
To be honest, I thought the Rubber mat from Pelle LePera would cost $2,000! I thought, but the effect is very Large.
If you have a problem like me, there is no harm in buying it. I think it will make your car travel more comfortable.
It's also the Items that change the Image of the commercial vehicle interior!
View detail
Buy for Repair
I lost the tip of my Ladder, so I bought this as a for Repair.
The texture is normal Material:The Ladder itself is not made by KIJIMA, but it is very sturdy.
As for the point that processing is necessary, I cut about 3cm for the length adjustment.
Because it is slightly oversized, I tie the root with Tie Wrap now to prevent it from falling off and use it.
I'm generally satisfied!
View detail
Compact
[How is it used?
I use it to put my Off car on High ace.
I used to use Straight's DRC Lamp, but it was too long and I had trouble storing it, so I replaced it with this foldable one.
Was the one you received as per Image?
As per Image
It feels a little heavier than I was expecting.
How was your experience with it?
It can be folded so that it can be loaded vertically, and of course it fits under the belly of the Motorcycle as shown in the photo, so you can use the space effectively.
It's great because I load three cars or a stupid load.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
The Rubber of the foot is a Replace product, so buy it when it is gone.
Hybrid Lamp Replacement Foot Rubber (https://www.webike.net/sd/23176446/)
View detail
For Transporter
I bought this to convert my TOYOTA HILUX into a transporter, and I think it is a must-have item because I can't put a larger size motorcycle on the back of the HILUX without lowering the gate. It is necessary to lower the gate of the cargo bed of the HILUX.
In addition, the Ladder slope is quite tight because of the high position of the HILUX cargo bed.
If you have a low height motorcycle like American, you need to hang the Ladder a little higher to make the slope slower.
In addition, when the back side of the cargo bed is surrounded by Ladder, it is important to note that it will loosen if the body is too small.
I haven't used it on any other vehicle other than the HILUX, so I'm not sure how it would work on other vehicles.
It is a convenient and happy point that this Ladder has two roles in one.
View detail
Fits: Others TOYOTA 200 series vehicles with high ace center console
Comfortable Goods
I've been driving a car that had Armrest as OEM.
I felt uncomfortable with this part when I switched to High ace.
The results were pretty good.
I thought there was a big difference in comfort between having elbows and not having them.
It is easy to install because it only needs to be plugged into the side Pocket of the Console.
The size is just right, so you won't have any gaps while riding.
View detail
Fits: その他 TOYOTA 200 series Hiace
Effective use of space
It is a product that can make effective use of Space.
It's very nice to be able to fit your phone in a little Space.
The points that I made in installing my
Remove the interior.
Relocation of the Switch
It is
I proceeded smoothly because the part such as removing the interior was the work done when I installed the car navigation system by myself.
In addition, it is the relocation of the Switch, but because there was already a Switch in the part where the Mount of the Smartphone Holder gets into, I relocated it to the bottom. Because there was the Switch of the Smart Phone Holder in the part where the Mount of the Smart Phone Holder is already hooked, I relocated it to the bottom.
Because the Wiring of the back was short, I pulled the Wiring by hand and stretched it and moved it though it was a little forcible.
By the way, iPhone12-Size can be installed without any problem!
View detail
Can be mounted at any location
I bought this for the purpose of applying Transporter's Tie DownHook.
Since it can be mounted anywhere in the Piping section, you can find a good spot to make a Spot by yourself.
I couldn't tighten the bolt very tightly because of Hexa, so I applied Screw lock agent to it.
View detail
Fits: Others 200 series high ace S-GL,100 series high ace S-GL
To prevent stains on Second seat
It is used for High ace for Transporter application.
I bought this to prevent the front tire from getting dirty because I press the front tire against the second seat to fix it when loading the motorcycle.
It is quite easy to install and easy to use.
Material is PelePera cloth, but Reverse side can be fixed with Magic tape, so there is no Gap.
It comes in two colors, so you can choose one that matches your decor.
View detail
Recommended
It is lightweight and has some strength.
The part that hangs over the body of the car is rubberized to prevent scratching. It is easy to use and recommended.
View detail
Very useful
I bought the Unit TruckLamp because I was having trouble finding a place to load the Ladder rail when I had two Motorcycles in my light Truck.
The one for the light truck is narrow and I might drop the Motorcycle Tire when loading and unloading, so I chose the wide and normal for Vehicle.
It is higher than the enclosure around the light truck, but it fits in without so much discomfort.
It was a good decision to go with this one because it is wide enough so I can still load and unload with ease.
It seems to be heavier than a normal Ladder rail, so it requires a bit of force to handle, and the folded part may open, but it is not a large problem.
There are various types of belts for light trucks, so if you choose the one that is easy to use, you can install it easily.
It is very convenient to expand the cargo bed which is not so wide of the mini truck by folding down the fuselage, and the mini truck also becomes a good transporter and pickup truck for parenthesis.
View detail
identification
I bought it to do Wiring.
I bought this colored Type to distinguish it from others.
Waterproof Cover is also included, which is good, but Quantity:Is this sale price for 1 Set of 5pcs. a good deal?
There are no other colors available, so I had no choice.
View detail
For Wiring
I bought this for Wiring.
It's affordable in terms of quantity and sale price.
It was also sold in a nearby shop, but the selling price, here was cheap, so it is a purchase with others.
View detail
for Replacement
It doesn't turn on, and when I look at it, Fuse is out, and it is purchased for Replacement.
This seems to be a bit cheaper than the parts sold at my local motorcycle shop.:1 Set of 3pcs. and it's not that expensive.
I thought it would not be a loss to have it in reserve.
View detail