Reviews
being fond of
I guess it's a matter of preference, but the plastic parts part is also Material:I think it would be good to have Aluminum. I changed the color to Aluminum. View detail
![Loading Hook for [MotorcycleGarageOption]Garage](https://img.webike-cdn.net/catalogue/images/69630/99045_TS.jpg)
Fashion in Garage
I use it for Jacket hanging.
Until now, the Hanger has been hooked to the gable end of Garage.
Merit to use this GarageHook, but I think it will only look better. You can choose any color you like, so it will be the one point in Garage.
The only demerit is that the Hook comes to a predetermined position, so the Hanger can only be hung there.
Even if you don't hang a Hanger, it can be used for a variety of purposes if you think of it as a hooked part.
To be honest, I could do without it, but it doesn't get in the way, and it would be useful if I had it.
View detail
Together with DAYTONARubber cord, it becomes a cord for fixing
[How is it used?
When you want to add a little more after fixing a large object with the ROK strap, or when you want to use the ROK strap for a large object.
To prevent misalignment, use a DAYTONARubber cord and this product.
I'm combining them and fixing them subsidiarily.
Was the one you received as per Image?
Yes
Was the installation difficult?
It was easy.
How was your experience with it?
The Hook looks Large in relation to the Rubber cord.
It has to be that large to fit on the back of a truck.
I was convinced that that was the way it was.
I am pondering how to make Hook fit better when putting the code together. (It's not that much of a problem.)
[Included Parts:were they on?
nothing special
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
DAYTONA Rubber cord can be attached
It can also be hooked to the thicker part of the cargo bed for Endurance's Rebel 250.
View detail
As a place to hang Netetc.
I bought it as a Loader Hook for a camping seat bag etc., but in the position where it was installed, it was convenient as a Hook to hang a Net. View detail
As a Loader Hook for Large tight Seat bag
It is useful when you don't have a loader hook or you have a hook but it is not well positioned. I have an Endurance Tandem Rear Carrier, but it has a hook only directly below where I place my luggage. Note that you may need a longer bolt depending on where you install it. View detail
A sturdy Loading Hook can be added.
This product can be easily added to a Cowl or Frame by simply tightening the Screws, and the strength of the Ring is perfect for camping touring! View detail
Various uses
[How is it used?
Used in combination to fix a certain company's Hook.
Was the one you received as per Image?
As per Image.
Was the installation difficult?
Just screw it in. No difficulty?
How was your experience with it?
Not used as it should be, but it is a dress-up element.
Leg.
[Included Parts:were they on?
As shown in the product image.
[Was there anything that disappointed you?
I also liked the color of the Silver?
Other items that would be helpful
Installation Point or hang Just screw it in. No difficulty. /Instruction Manual No. Ease of understanding ○○/Points to note None. Items to be purchased with Depends on the combination/Opinions and requests to Manufacturer I wonder if the delivery time is long….
View detail
To Hook for Transporter of DA17V
I bought this as a Hook for my DA17V Transporter. It is solidly made and seems to be able to endure a considerable tension. At first I was looking for a suitable Universal Product in Home center, but when it was difficult to find easily, I found it in webike, so I bought it.
I bit into the driver/passenger fixed Bolt and saw that it was just right.
OEM Cover can also be covered when Hook is not in use
Quantity:I bought 2 sets, and I thought I would fix them to the Bolt (floor side) of the Seat belt of the Rear seat.
I had to extend the hole to 12mm because the sutra didn't fit.
It is easier to buy this product than to go around the home-centre, though the cost is not equal to the Universal Product of the home-centre.
View detail
M8 is better
I bought this product to fix my 25mm Belt, because the screw near the Carrier is M8 and I could only find this product. （The screw around the carrier is M8.)
It's a little expensive, but it can't be helped.
View detail
Fashion.
The Bolt was a little short so I replaced it with one from Home center.
I was able to replace the Bolt to fix the Seat and add the Hook.
It looks Fashion and can be enhanced for loading.
Dress-up is also a Recommendation.
View detail
I installed it on a TrayWagon.
I installed the TrayWagon to make it a Transporter. It is Exactly the same as the original M8 hole. It seems to be strong enough and I made a good purchase. View detail
Because the OEMHook bolt is cheap.
I took the plunge and replaced the OEM Hook bolt because it was not good.
It is longer than OEM, but I personally don't mind.
It looks better
View detail
The more fixed places, the better.
There is not enough room to hang Tie Down on the cutting board Trailer and I want to make a fixed place on the top board. I want to make a place to fix it on the top board.
It's nice to have an extra fixed location for more peace of mind.
Another good thing is that you can set yourself up in a place where Tie Down works well.
View detail
It's small and has a good shape.
I bought it to put my stuff on the seat and hang the hook.
I haven't used it as a hook yet, but it's a good Accent.
You may never use it just for looks.
View detail
I use it for High ace.
I'm using it with the Floor panel of OGUshow.
Essential Items for creating a Transporter car.
It is not bent at present, so it is well made.
View detail
The more fixed places, the better
[Motivation for purchase]
Because there were no rear hooks
The deciding factor in the purchase
Buy it with the Motorcycle Accessories
【attachment】
Just use an M8 bolt to hold it in place
My Thoughts on Actual Use
You can now pull in the rear direction and sink the suspension
Areas for improvement
nothing special
Comparison Products
nothing special
【Review】
It was installed as an OEM product
This should prevent the Motorcycle from collapsing in the car …!
View detail
I use it to hook up the Transporter Tie Down
Tie Down Belt when loading a motorcycle into a Transporter I use it where
At first I installed the Eyebolt, but it got in the way when I didn't use it, so I changed it to this one I did
I think it's very good
The quality and strength are very good
Minus the slightly higher price point
https://plaza.rakuten.co.jp/runoncircuit/diary/202001230000/
View detail
I was able to install a Loading Hook on my Jimny JB23W (=PωP)
Inch BoltW5/16Size was available, so I looked for a Hook and found the M8Screw The only size I can find is DAYTONA's Universal Loading Hook It was (I can't find the same size product in Amajohn.)
Quick installation
This bracket is designed to tie down a motorcycle, so it is durable and not deformed
I had no problem holding back six cans of kerosene
View detail
usually
This is a common CargoHook bolt
Since the rear support of the R1200RS is removed, it is installed in a vacant place
I was able to install it with no problems
You need a longer size bolt because it is not long enough to be buried in the back to
View detail
Something useful.
NV350 (DX) I am using it.
Bolt and Washer are not attached, but I thought that it was rather unassociated and it was a correct answer because various lengths and materials were available at home center according to the way of installation.
The building is solid..
View detail