Reviews
Stable
The CT110 HUNTER CUB had a Seat that was too Flat, causing the body to fall backwards during acceleration, and my back would ache if I rode it for a long time.
The backrest supports my waist, which stabilizes my body and reduces the burden on my back, and the footpeg and backrest help stabilize the car body when turning.
The construction is solid and seems to be strong enough, and it is possible to sit lightly on the backrest when standing.
As a Demerit, I can't sit deeper in Seat, so my buttocks hurt a little faster because I can't distribute my weight with my thighs.
If you are taller than 180, your legs may feel cramped.
View detail
Case of another Manufacturer.
We were looking for a case from another manufacturer, but when we tandem the case, my daughter said it was too stiff when she leaned on it....
The included Screw cannot reach it because of its different shape, but we were able to change it to 40mm and install it.
It seems to stick out a little, but in my daughter's opinion, it is GOOD!
View detail
It's very easy.
I bought it because I read that it was good in your impresion and I had back pain.
It is so good that I wish I had installed it sooner.
The work takes about one hour if the tools are available.
The instruction manual can be downloaded from the enclosed paper via QR code or Honda.
Personally, the most time-consuming part was the final installation of the back Cover.
I had a hard time getting soapy water on it and pushing it in.
View detail
Back rest installed.
[How is it used?
Used in Touring
Was the one you received as per Image?
As per Image
How was your experience with it?
They say the Rear seat is comfortable.
[Points to note]
Base is purchased and installed.
How did it compare to other products?
Base is a little high in price.
Others
There are bolt and clip fasteners on the base, and the clip fasteners are easy to remove and may cause the backrest to fall off while driving.
Seat cannot be removed if backrest is installed with screws.
View detail
It's pretty good
I don't like Style, but it was surprisingly easy.
It will be difficult to get in and out.
The installation could be done by myself by referring to Youtube from abroad.
It is uncomfortable to lean back with a lumpy spinal pad on your back.
We are seeking to do something about that.
View detail
Fits: YAMAHA TMAX500, YAMAHA TMAX500, YAMAHA XMAX
Designability is also fat.
The material is a rubber-like material and hard.
However, it is not so hard that it hurts to lean on it.
Installation is as simple as drilling a hole in the top case and fastening with a screw.
We have not yet tested the waterproof property of the installation, but there was no flooding with just a car wash.
View detail
Yamaha Sissy Bar For Yamaha Bolt R-Spec
About quality and texture - Quality is good, but the paint will show marks from things being strapped to the Sissy Bar if you are not careful. About the feeling of use - Needed if you are going to take things with you on a long ride, like a knapsack. Products to buy together - You need to also puchase the Backrest Arms to mount the Sissy Bar to. Luggage Rack is optional. Difficulty of installation - Installation is not hard. You can do it alone, but much easier if you have someone to hold the parts while you install the bolts and tighten them down. Cost performance and comparison with other products - More expensive than one from China, but fits better and is the right color. It is also a Yamaha part. About shipping and packaging - Excellent. Any concerns, cautions, or advice when purchasing - None View detail
Pad only.
I don't understand why they are only selling the Pad.
The appearance is the best match to the design of the Rebel 1100, and the texture is also excellent.
However, I can't understand why the pad is sold separately.
View detail
Low Backrest
Quantity with Pad:I am not happy that it is not a Set.
No one will install this on a single body.
It is a little shorter than the external backrest, and I chose it because I thought it would best match the style of Rebel, and I was right.
The ability to Catch the Passenger's buttocks to prevent them from falling off during acceleration is not a problem, and can also be used when strapping luggage to Rear Sets.
The texture is as OEM as you would expect, very good.
View detail
It is just the right Size.
I like the size, which is not obtrusive, but still makes a statement.
It is not recommended, but it is convenient to hang a bit of Helmet.
I think the quality of the paint and the quality of the OEM parts is quintessential.
Since Tandem is almost never done, the appearance is determined though the Parts are attached only by Parenthesis.
But the fact that the pad is sold separately is a little bit annoying...
View detail
Design-oriented Tandem backrest bar installation
Proper painting (Lol)
Well, the design is good, but it's expensive. (Lol)
If you have the tools, you can install it in 10 minutes?
View detail
Installed on GIVIRear boxE26N!
I was looking for one that would fit for my GIVI 26L.
Align it with the R, position it, drill the holes, and install!
Feels a little firm, no discomfort at all!
View detail
The original Honda rear backrest can be installed to make up for the inconvenience of the factory without a backrest
Honda's original rear backrest is suitable for Rebel 250/500 models. After installation, it can make up for the inconvenience of no rear backrest at the factory. It provides a sense of safety for the rear seat passengers and can be installed with the rear shelf. It can be used to load motorcycles. Traveling luggage greatly increases the convenience of traveling! However, the position of the backrest is a bit low, which is not suitable for the function of the backrest! ----------------------- ----------------------- Honda (Honda) applied to the original backrest Rebel 250/500 models, the installation can not make up the backrest inconvenience factory, provides security for the rear seat passenger can be installed with the rear shelf, a motorcycle can be used to load luggage travel greatly increase the convenience of travel! position back but a little bit less in line with the function of the low back! Powered by Google Translator View detail
Easier to handle
Because there is a kind handling Instruction Manual.
You do not need to be a PRO to work with it.
Depending on how you do it, you can do it without shifting the Fender as per the Instruction Manual.
It would have been 120 points if the included Bolt was Stainless Steel.
View detail
Decent product
In all, good quality and no problems with fitting and chrome. Welding somewhat coarse, maybe Tig instead of chosen method. View detail
The peace of mind of an OEM
It feels luxurious and rigid.
I compared it to other companies' products, but chose the Y's Gear product because it was made by Pipe and felt cheap.
The price seems quite overpriced, but as only an OEM can do, it feels safe and satisfying.
I feel that a little more angle would allow for a more relaxed two-seater.
View detail
Fits: Others B47, KAWASAKI VERSYS-X 250, Others B37
Focus on appearance
I don't normally do Tandem, but I personally think it will improve the look, so I bought it. I didn't have an electric drill, so I wasn't sure how to drill the Case, but I was able to drill a preliminary hole with the Drill and then pry it out with thin Scissors. I am very happy with the look and feel of the case. View detail
Fits: Others B47, KAWASAKI VERSYS-X 250, Others B37
For Tandem
We rather often do Tandem as a couple, but GIVI's B47 hurts where the back hits, so we bought a Backrest in preparation for long touring.
You need to drill holes for mounting, and I'm concerned about water immersion, but it also included RubberWasher, so I wonder if it's Large sturdy.
The inside of the B47 is positioned to be drilled, so it's not a problem if you drill a 6.5mm hole as per the Construction Manual for easy installation.
The Cushion is also softer than I expected, so they said the comfort during tandem has increased.
View detail
It keeps you in a comfortable position!
As per the installation instructions, I noticed when I removed the rear cargo bed and fixed the base and installed the rear box, when I opened the lid of the rear box, the base of this product was hindered.
That's why I made a hole in the RearBOX directly only the Cushion part and fixed it with Screw stopper as shown in the picture. I used to ride on the RearBOX by leaning directly on it, but I had a problem that the RearBOX hit my back when I passed the bumps, which was painful. However, the problem was solved by installing this and comfortable position can be taken. It's not the same as the original image, but I'm glad I bought it!
View detail
I recommend it as a Backrest.
I'm 170cm, 58kg, normal build, but it's just right for me personally. However, those with a good build may feel a bit tighter.
Installation of this product is to insert the seat into the rear suspension part. It may interfere with the Rear Suspension part of the Carrier which is already using the Rear Suspension part.
I was able to use it together with the Tandem Backrest for CROSS CUB of Wills WIN, which is like removing the Spacer from the rear suspension.
By the way, I received my own screw with the pad part temporarily fastened. You can buy more screws at the home center, but it's too dangerous and I wanted to send them separately.
View detail