Reviews
![14. Grip End Cap [Grip Heater HG: Repair Parts]](https://img.webike-cdn.net/catalogue/images/30252/08T50HANE21_1_TS.jpg)
Hole concealment of fret & mdash;厶
Holes were drilled and painted Silver. View detail
![Grip Heater 115 [Grip Heater: Repair Parts]](https://img.webike-cdn.net/catalogue/images/31601/08t50hane01_01_TS.jpg)
Replace only Left when replacing Handlebar.
Originally used HG115.
When replacing the handlebar, the Left Side could not be removed cleanly and could not be ported.
Because the inner elasticity is Zero, if it is bonded, I have to break it and remove it.
We were glad to be able to sell the product in component units and not have to buy a complete set.
View detail
Fits: HONDA CBR125R, YAMAHA MAJESTYS, YAMAHA MAJESTYS, HONDA MONKEY125, HONDA FORZA Si, HONDA dunk, HONDA ZOOMERX, HONDA glom, HONDA glom, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA glom, HONDA PCX, HONDA PCX HYBRID, HONDA PCX, HONDA PCX, HONDA PCX, HONDA CB250F, HONDA CBR250R
Good item for monkey 125!
It's a really good product. Both the finish and the design are excellent. Thank you for your prompt delivery. I recommend this product to others, too. View detail
I'm ashamed to admit...
I'm ashamed to admit that I put the Grip on before I put the Controller on, and now it's too late.
It is impossible to remove it again with reusable Level, so I had to buy a new one at Repair Parts.
The result was expensive, but the Quantity:I'm glad it's still better than buying 2 Set. (;^ω^)
View detail
Fits: HONDA PCX HYBRID, HONDA PCX e HEV, HONDA PCX160, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX
Unity in Endurance
Purchased at the same time as Endurance Custom seat. The specs are the same as in the product picture. I am satisfied with the Large size. I am satisfied with the design and functionality. View detail
Fits: HONDA CBR125R, YAMAHA MAJESTYS, YAMAHA MAJESTYS, HONDA ZOOMERX, HONDA dunk, HONDA FORZA Si, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA PCX150, HONDA glom, HONDA PCX HYBRID, HONDA PCX150, HONDA PCX150, HONDA CBR250R, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX, HONDA CBR250R
Convenient for hanging a small shopping bag or Helmet.
I purchased Red.
I installed this on my pcx 125 jk05. I like the fact that the limited space around the handlebar is not sacrificed since it is tightened to the master cylinder and does not require any extra mounts.
It is solidly built and has a good texture.
As it is called a "Convenient Hook," it can be used with no problem if it is just a small bag of groceries at Convenience.
Bags purchased in SUPER large quantities can also be hung, but please note that the foot space will be cramped.
It is also convenient to hook the D Ring of the Helmet during Small breaks.
I think it is such a Must-have item that Scooter should make it a Standard Equipment.
View detail
Installed on a 2021 MT-09SP
I was thinking that I would not need a Loader Hook since I have a Seat Bag attached when touring, but I bought this Hook because I thought it would be useful for touring around the neighborhood without a Seat Bag attached and for bringing back food I received while on the road. I bought this Hook.
At the time of purchase, the one made by DAYTONA was cheaper on sale, but it had a 2-piece structure, so we decided to go with Endurance, which has a one-piece structure and a clean shape.
The length of the Bolt is 40mmType which makes the protrusion the same length as the OEM Bolt.
When used with Endurance's Rear Carrier, the 60mm Type seems to be used.
The SeatBack is convenient, but since we have short legs, the bag makes getting in and out of the car a hassle.
Net bought 30cm×30cm, but when I put it on Hook, Seat becomes boneless ham, so a little larger size might be better.
View detail
Fits: HONDA cross-cub 110, HONDA Super Cub 110
Exclusive goods
Grip heater made by Endurance with voltmeter function was selected in preparation for cold wave attack.
I checked the actual vehicle to purchase UniversalThrottle pipe.
JA10 is Throttle Cable1 pc pull…
The successors JA45 and 60 are Quantities:2pc pull not compatible…
I searched the Net for help from my predecessors.
Quantity:There is also an atmosphere of processing and using 2pc pulls…
I bought Endurance's exclusive products honestly.
Grip heater has been installed many times in other cars.
Finished quickly, no problem because it is a dedicated product.
Fingertip problems. [Color] Clear!
I never felt cold when I was in my 20's. Is it age?
View detail
Fits: HONDA dunk, HONDA FORZA Si, HONDA GROM, HONDA GROM, HONDA ZOOMER-X, HONDA MONKEY125, HONDA MONKEY125, HONDA CBR125R, HONDA CT125・CT110 HUNTER CUB, HONDA CT125・CT110 HUNTER CUB, HONDA GROM, HONDA GROM, HONDA GROM, HONDA PCX e:HEV, HONDA PCX HYBRID, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX
Convenient for a little shopping
Convenient for a small amount of luggage
If the volume is too large, Handlebar is taken.
I wish the Hook department also belonged to Gold.
View detail
Fits: HONDA Rebel 500, HONDA Rebel 500, HONDA Rebel 250, HONDA Rebel 250, HONDA Rebel300
DIY OEMHelmet holder also installed!
The installation method is described as a reminder.
If you install it yourself, you do so at your own risk.
Installation time:20 min.
Required tools:Torque wrench (10mm, 13mmSocket), 6mmHexagonal Wrench?
?Instruction Manual is not included, so you can look at it first on Net.
Temporarily assemble the backrest.
? For now, so just hand-tighten it!
?Quantity:Pair (for Left and Right) Bolt next to the Rear Fender of Quantity:Remove 2pcs (6mmHexagonal Wrench).
? It is quite stiff and can be easily removed using Glasses Wrenchetc.
?? Temporarily fasten to the car body with the supplied Bolt.
When installing the side bag support, use the bolt for the side bag support without the hanger plate.
If you want to add a hanger plate, you need to purchase Bolt separately.
Retighten the backrest bracket (13mmSocket:24N.m).
Retighten the mounting portion of the backrest (10mmSocket:10N.m).
Installation is complete so far:===========
How to install OEMHelmet holder:60-90 minutes
Neji-saurus is purchased and removed.
See Neji-saurus impresario.
Make a hole with a 6mm drill around the bottom of the upper hole on the side where the Backrest Bracket will be installed.
The size of the lens must be gradually increased from 3mm to 4mm to make it large enough.
? I only had up to 5mmDrill on hand and was forced to widen the hole.
Remove the mounting plate of the OEMHelmet holder with the Neji-saurus.
Attach the OEMHelmet holder to the back restBracket with the removed screws (security and screw reuse).
Tighten with Neji-saurus.
==============================
If side bag support is installed, the procedure may be slightly different.
The backrest is a nice touch to tighten up the silhouette!
The OEMHelmet holder could not be used when the side bag was installed, so the Backrest Bracket was modified.
If you don't want more keys and are considering DIY, please refer to this page.
View detail
Fits: HONDA Rebel 500, HONDA Rebel 500, HONDA Rebel 250, HONDA Rebel 250, HONDA Rebel300
Perfectly compatible with double seat. It does not affect the loading SPACE.
Since it is a CruiserType, we considered Backrest.
We were looking for something that was easy to purchase in terms of price and Simple construction, and decided on Endurance.
I was worried that it would interfere with the DAYTONA Grab Bar Carrier, but I was able to install it without any problems. I was worried that it might interfere with the DAYTONA Grab Bar Carrier, but I was able to install it without any problems.
I think the installation of DAYTONA's Grab Bar Carrier occupies the Bolt along with two Washers from the Rear Fender, but if you remove one Washer and install it, it will be just fine.
Fender → Backrest → Washer → Carrier.
As usual, the Rear circumference must be carefully inserted or the Screw hole may be broken, so it must be occupied slowly while temporarily holding the four screws in place.
The load area has become narrower, but it is still more than 20 cm and can carry a seat bag, etc. It seems to be able to do a one-day camping trip in Tandem.
View detail
Fits: HONDA CBR125R, YAMAHA MAJESTYS, YAMAHA MAJESTYS, HONDA MONKEY125, HONDA FORZA Si, HONDA dunk, HONDA ZOOMERX, HONDA glom, HONDA glom, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA glom, HONDA PCX, HONDA PCX HYBRID, HONDA PCX, HONDA PCX, HONDA PCX, HONDA CB250F, HONDA CBR250R
Convenience
Foot Motorcycle so shopping convenient with Convenience.
Installation is easy. Be careful not to hang something too heavy as it may cause the HandlebarBalance to collapse, but in the neighborhood, no problem.
View detail
Fits: HONDA CBR125R, YAMAHA MAJESTYS, YAMAHA MAJESTYS, HONDA MONKEY125, HONDA FORZA Si, HONDA dunk, HONDA ZOOMERX, HONDA glom, HONDA glom, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA glom, HONDA PCX, HONDA PCX HYBRID, HONDA PCX, HONDA PCX, HONDA PCX, HONDA CB250F, HONDA CBR250R
Nice hook
This is a useful item. The installation is very simple. The delivery and packaging are excellent. I chose black. Simple is the best. View detail
Fits: HONDA CBR125R, YAMAHA MAJESTYS, YAMAHA MAJESTYS, HONDA ZOOMERX, HONDA dunk, HONDA FORZA Si, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA PCX150, HONDA glom, HONDA PCX HYBRID, HONDA PCX150, HONDA PCX150, HONDA CBR250R, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX, HONDA CBR250R
Installed on MONKEY125
I can now go shopping without carrying a bag.
I don't use it often, but it's better to have it than not to have it.
View detail
Fits: HONDA dunk, HONDA FORZA Si, HONDA GROM, HONDA GROM, HONDA ZOOMER-X, HONDA MONKEY125, HONDA MONKEY125, HONDA CBR125R, HONDA CT125・CT110 HUNTER CUB, HONDA CT125・CT110 HUNTER CUB, HONDA GROM, HONDA GROM, HONDA GROM, HONDA PCX e:HEV, HONDA PCX HYBRID, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX
Mounted on PCX160
I bought this product because the Convenient Hook is not attached to the PCX, so it is easy to install.
The only thing you need to do is to change the master cylinder holder, but if you hang something heavy on it, the handlebar might be taken off.
It looks like you can only hook up light objects.
Because it is not the thing of the dress-up purpose, it becomes uncomfortable when the holder of the opposite side is dress-up.
View detail
Fits: HONDA CBR125R, YAMAHA MAJESTYS, YAMAHA MAJESTYS, HONDA MONKEY125, HONDA FORZA Si, HONDA dunk, HONDA ZOOMERX, HONDA glom, HONDA glom, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA glom, HONDA PCX, HONDA PCX HYBRID, HONDA PCX, HONDA PCX, HONDA PCX, HONDA CB250F, HONDA CBR250R
After a quick shopping trip to Convenience
Hook to hang small bags and other items for small purchases.
The texture of the Aluminum Cut-out+Anodized process is also a nice touch.
View detail
![Main Harness [Grip Heater: Repair Parts]](https://global.webike-cdn.net/photo/impression/5c/5c4a48cf989f829c3c64f9e688b81d1dL.jpg)
Grieg's Wiring break as Repair item
At the moment the Voltmeter of the Switch did not turn on or not, the voltage was pointing at 8 V
It disappeared and it was broken when I checked it.
Wiring's handling is marginal (I gave it myself) From the Bullet Terminal part of the Coupler the line is blown out
I got it.
Since it is a special item, it was corrected without problem.
View detail
Fits: HONDA cross-cub 110, HONDA Super Cub 110
It saves labor and time to process
I also thought whether to handle the removed Grip with a hand-held tool, but it takes time to finish this product as well, considering the fact that such a place as the installation place of Wiring and Indicator of Grip heater etc. is lost, Whether it is better to purchase this product.
It is very beautifully shaped, and if you look at the actual thing, I already bought it and it feels like a correct answer.
View detail