Reviews
Fits: TRIUMPH STREETCup, TRIUMPH STREETTWIN, TRIUMPH SpeedTWIN, TRIUMPH THRUXTON, TRIUMPH BONNEVILLET100, TRIUMPH BONNEVILLET120
able to be used for two purposes
It is painted black, so it is hardly noticeable even if the side bag is not attached.
The shape of the Bracket makes it possible to attach not only the company's Side Bag but also other companies' Side Bags.
Just one point. My vehicle was installed with some of the extensions connected, but I'm worried that the Nut is very close to the Rear shock, so I'm not sure if it will make contact.
View detail
Exclusive Design.
The gap between the right side and the body is the same as the right side. View detail
It's Exactly because it's dedicated.
It's a little disappointing to see it from the back because it's a little far away from the car body. View detail
Fits: Others Hepco & Becker Side case Explorer/Journey/Junior/Gobi
Securely mounted.
Firmly and Pannier can be worn.
However, I think the price is too high.
View detail
The product is good, but the accuracy is not good enough.
The product itself seems firmly and sturdy and gives a sense of security, but we had the following problems in installing it.
When installing the new machine, even the screw holes were painted, so it was necessary to make a tap.
・Quantity:Pair (for Left and Right) The holes in the Parts connecting the Holder of the Bracket were not aligned with the Screw holes in the Bracket and needed to be corrected.
The mounting holes of the parts to which the blinker is attached are small, and the rubber part of the blinker is deformed, so it was necessary to widen the holes with a file.
Wiring had to be extended because the Blinker would have to be moved.
I asked PRO to install it for me.
Since it is quite expensive, I was expecting a good degree of accuracy.
View detail
Weak rigidity of the bar
I installed it on my 2nd model MT09SP, but it is a large size because it interferes with the controller of the rear suspension. The bar is not rigid, so when the back is attached, it bends inward, so I have to check the interference with the tire every time I attach it. View detail
Fits: SUZUKI BURGMANSTREET125EX, SUZUKI DL1000 V-STROM250SX
At the risk of sounding like an obstructionist... ('◇') voiced repetition mark in hiragana
However, we decided to publish this information because it is useful for DL1000 V-STROM250SXUser!
It is exactly the same as the fitting plate that comes with the GIVI Mono-lock case when you buy it.
The only difference is that there are four additional colors circled in red on the photo.
In a sense, it can be purchased at a PRO-like home center, or it can be assembled without it, so it does not matter whether it is there or not (although it would be stronger if it were there).
So, it may not be worth buying except for the use that you want to stock OEM boxes as well. Hmmm.
View detail
Fits: HARLEY-DAVIDSON XL1200, HARLEY-DAVIDSON XL883
Am I putting it on the wrong way?
Installed on an XL883N (2019). The Bolt on the back side of the bike is threaded on the Fender side, so it is easy to loosen and install, but on the front side, it is nutted. Therefore, it is not possible to remove the Bolt by simply loosening the Bolt and sliding it off. In addition, it is not possible to leave a space of about 5mm between the attached cylinder-like part and the loosened Bolt (Bolt is not long enough?). (Bolt is not long enough). The longer cylindrical part is not used and is fixed in place.
I don't know if it is a problem with my installation/motorcycle or the product.
View detail
Fits: HONDA CRF1000L Africa Twin, HONDA CRF1000L Africa Twin Adventure Sports, HONDA CRF1000L Africa Twin, HONDA CRF1000L Africa Twin Adventure Sports
attachment
Installation required a deep socket, and the exhaust system had to be removed, making installation a bit of a hassle. View detail
Technology.
Installed on a 2022 h2sxse after model change
Need to expand the hole because the fixing screw has been changed from m6 to m8.
We also need to get a new Screw (we use m8x45 and m8x40 as Quantity:Buy 2pc each)
And SmallerScrewQuantity:Purchased additional 2pcs because they were not long enough. I forgot the length.
It took me a whole day to install it because I was a beginner because I had to remove all the covers and tail lamps from the rear.
The Bracket is inserted between the Frame and the Fender, but since the 2022 Fender will have a sensor to detect blind spots, it is quite heavy and could not be done by one person.
Also, the fitting kit is fixed with a screw on the Tandem Footpeg, but it cannot be fixed because of the helmet lock, and even if the helmet lock is removed, it cannot be removed because a special screw called one SIDEScrew is used. I tried to remove the helmet lock, but I could not do so because it uses a special screw called one SIDEScrew.
Finally, I purchased a footpeg from the new KawasakiOnLineShop! (8,000 yen (´ωTranslated) Tohoho…)
Finally, Plate for Monokey is available in m5 and m7, but m7 is more Refreshing and Recommendation. It is a bit expensive, but you can find it at ....
View detail
Fits: HONDA NC750S DCT, HONDA NC750S, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER BOLD'OR, HONDA CB1000R, Others , HONDA NC750X DCT, HONDA NC750X DCT, HONDA NC750X, HONDA NC750X
I still can't deny that it looks cheap.
It can't be helped that it is a dedicated part, but it still looks cheap.
There are many parts to install, and they have not been installed yet. As an amateur, I feel like I have to work hard in terms of menbarrel to install something this solid, but I am looking forward to seeing where it goes, so I will make time to do my best.
View detail
Fits: YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100Classic
Quantity:Pair (for Left and Right) Might we need it?
Necessary to prevent Side Back entrapment.
It is easy to install.。
Required when installing Side Back on American without load capacity.
Accident prevention.
The other side is also needed.
View detail
No scratches on Swing Arm
Installed on a Forty-Eight, the Swing Arm is not damaged, but the Bag Support does protrude outward from its mounting position. View detail
Fits: APRILIA SHIVER 750, APRILIA SRV850, BMW C650 Sport, DUCATI MONSTER 1100, DUCATI MONSTER696, DUCATI MONSTER796, HONDA CBF1000, HONDA CBF500, HONDA CBF600 N, HONDA CBF600S, HONDA CBR600F, HONDA CRF1000L Africa Twin, HONDA CRF1000L Africa Twin, HONDA VFR1200F, HONDA VFR800, HONDA VFR800, HONDA VFR800F, KAWASAKI ER-6f, KAWASAKI ER-6f, KAWASAKI ER-6n
Screw hole mismatch
It did not fit the fitting (bracket) slightly, so I had to modify it a little. If possible, it might be safer to have someone with knowledge or a store install it. View detail
Unavailable features
There is a claim that it can carry a U-Lock, but I can't find a U-Lock that fits this at Motorcycle supply stores. View detail
Appearance is not so clear
Installation was easy and quick.
I haven't run with the Back installed yet, so I don't know how strong it is.
View detail
Fits: YAMAHA MT-09, YAMAHA NIKEN, YAMAHA TMAX, YAMAHA TRACER9, YAMAHA XMAX
Mounting LargeChange!
The installation was a hassle anyway, I had to remove the Cowl around the Rear and the Damper at the SIDEPannier mounting point to install it.
If they had thought a little more about the design of the Mount plate, it would have been easy to remove the Grab Bar and install it.
The product itself has a sporty design and is unobtrusive when the Rear Box is not worn.
View detail
Fits: HONDA CB650F, HONDA CBR1000RR, HONDA CBR400R, HONDA CBR250RR, HONDA CB400SB, HONDA CB400SF, HONDA CB650R, HONDA HAWK11, HONDA CB1300SF, HONDA CB1300SB
Let's see if it's BF03 or BF30.
I have a CB1300SB22 and I initially ordered BF03 by mistake. I recommend you to check whether BF03 or BF30 is the one that fits your Motorcycle.
The installation is no problem, as it is done with 3 screws. However, the quality of the attached hexagonal screws is not so good... If you are concerned about it, you may want to replace them with StainlessScrews.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS, KAWASAKI Z900RS, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE
To install Tool Bag
I purchased this to install a small side bag or tool bag. I purchased this bar because the existing Pillion Bar was also made by KIJIMA. The color, texture, and pipe diameter are the same, so there is no discrepancy. I didn't really want to install it, but I didn't feel comfortable using only standard tools. View detail
Material:Plastic, so I'm concerned about deterioration over time.
[How is it used?
I used SHAD's Rear boxfor Repair.
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
Large sturdy if ready for Bracket.
How was your experience with it?
It is convenient because it can be removed by One-touch.
[Included Parts:were they on?
There was not.
[Was there anything that disappointed you?
Material is Material:It is Plastic and will whiten over time.
Any more than that and it would have become brittle and needed to be replaced.
View detail