Reviews
Quality control or packaging issues
Installation is Level, which is fine for Beginner.
No special problems with the feel of the product.
However, there is a relatively noticeable scratch on the base plate section….
Was the shipping check lax, or was the packaging messy and damaged in transit?
It's not a practical problem, but ….
The mood is lowered by the relatively expensive components.
View detail
RearCarrierQuantity:Pair (for Left and Right) The bracket does not align with the base mounting holes on the top case.
I purchased this product to install GIVI's Mono-lock case 47 on my F900XR. I would like to comment on the installation process and the state of use.
(1) RearCarrier's Bracket is LeftOnly Right and Quantity:Pair (for Left and Right) Since there is no Bracket to link the Quantity:Pair (for Left and Right) There is some difficulty in determining the horizontal state of the Bracket.
The ?Instruction Manual is somewhat confusing.Quantity:Pair (for Left and Right) It would be good if the distinction between Bracket and the reverse side is clearly indicated.
(3) Base plate hole and quantity on the bottom of Top case:Pair (for Left and Right) Bracket holes are FrontQuantity:Pair (for Left and Right) Two of them fit, but not the Rear. However, the Rear hole was not inserted, and since the Bolt hole was shifted from the normal position, I am not sure about its strength.
Also, the position cannot be adjusted back and forth.
?There are no strength or other problems so far in using Top case, but the position of Top case is quite high.
I would like to see the Bracket extending to the rear of the vehicle reshaped so that it is lower. Also, the Top case is slightly further rearward than the rear wheels.
View detail
Fits: YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT03
QC CRAP!
About quality and texture I bought this as an alternative to $expensive$ luggage kits. I used it with oxford soft saddle bags. Later on to be used with refashioned, custom saddle bags for a stylish look, which would be harder to fit to proprietary equipment such as GIVI. Hence use of a simpler mechanism such as this one Easy to install, although instructions were in japanese It fundamentally works as intended, but its very heavy, pure steel construction. unfortunately, on this brand new product I found chips in the paint, welding is of low quality upon arrival. Sure its cheaper than other options, but the weld should not be so cruddy that i could have made my own one of same quality for a quarter of the price and my own time. You will see the welding yourself in my photo, judge for yourself. I think this product has a higher weight-limit than it is listed, because the steel rod is very thick and heavy. The unprofessional welding will fail before that bends. I have had mine 3+ months with no failures. shipping was pretty fast from JP to AUS. I don't recommend this product to anyone with spare time and equipment to fasten and tap metal. Just do it yourself as the price is simply not justified. Be careful with shorty style exhaust, as with large saddle bags the bottom of the bag can melt in this setup if is not heat-resistant. I can smell mine burning sometimes on a hot day sitting in traffic, lol. View detail
Buy something different.
The same Type can be purchased on Amazon from an unnamed Brand.
Laflo is expensive.
View detail
I'm not happy with the accuracy
I purchased this product to distance myself from the Exhaust System.
The holes are gapped when inserting the Nut, making installation difficult.
However, it is Steel and rigid, so it is safe.
View detail
Fits: HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CBF1000 06, HONDA CBF1000 07, HONDA CBF1000 08, HONDA CBF1000 09, HONDA CBF1000 10, HONDA CBF1000 11, HONDA CBF1000 12, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500
Exclusive goods
I feel that it does not have to be a dedicated product. View detail
Incompatible with Fender Eliminator Kit
I bought this because I want to install a Saddle Bag.
If you install it, you can't use Helmet holder, but it's not used much. (Difficult to use) So there was no problem there.
However, it is not compatible with the Fender Eliminator Kit that I originally installed. It's not a problem at Level, but it's bothering me.
View detail
When you first buy it, you need rust protection!
Overall, it's a rough product, or rather, it's delicate when you think of it as a product of a large hand manufacturer.
The finish was dirty due to poor welding, and I was wondering if it would rust.
I used rust remover while it was still minor, applied rust inhibitor and no problems since.
I wonder if the cost is not too good.
Exclusive Bracket with dirty weld marks and easy to rust, Material is Steel.
However, it is only a special product of the Large hand manufacturer, and the accuracy itself is not bad.
The dedicated bag is also easy to install and can be fixed firmly, so the performance itself can be evaluated.
It's just that it's poorly made and the price is not commensurate with the product.
View detail
Fits: BMW R1200RS, BMW R1250R, BMW R1250RS, BMW R1200R
impressions
The special Spacer was missing.
I had no choice but to buy something similar from Home center and install it.
Others are normal but Cost performance is not good.
View detail
Fits: YAMAHA XV 1100 Virago, YAMAHA XV 750 Virago, YAMAHA XV 750 Virago, YAMAHA XV 1000 Virago
This is not something an amateur can install.
There are too many problems.
The only thing that fits is the Hole Pitch.
It is not possible to install it as it is.
It requires processing and ingenuity.
BlinkerWiring will also not be able to reach you.
The release position of the Blinker positioning protrusion is incorrect.
Interference with Sissy barFrame.
It must be at least 5mm more and the round bar mounting position must be on the outside.
The round bar is too far inside and the Bag interferes with the Suspension.
Normal people shouldn't buy it.
View detail
Fits: BMW R1250RS, BMW R1250R, BMW R1200RS, BMW R1200R
The installation deflated
I installed it because it was exclusive to the car model, but Screw is the quantity:Set of 2pcs is missing … Also, you don't need Stopper for Case completely When you install the Case, you have to push it in with considerable force No. Clearance is a mess It's a shame because the texture is just fine I will never buy this Manufacturer's again View detail
Fits: YAMAHA YZF-R1 M, YAMAHA YZF-R1
For a simple product..
It is a little difficult to install
It was difficult to fit the rack to the screw holes firmly, but once you get used to it, you can get used to it What a mess
It's a great way to put a large seat bag on, for camping and for self driving sessions You can use it in various ways, such as
View detail
Installation is limited
You need to be creative when you install it It is not always possible to install all the side bags and models of cars
My Side Back is The "AQADRY Side Bag The width is long in the Considering the position of the hips, the Front side Belt is just behind the Tandem belt and the Rear The side Belts will inevitably pass over the Rear Fender Now what to do? Right now, I'm puzzling over the Large size of it …… (*Motorcycle = CRF250L)
View detail
Fits: DUCATI Panigale 959, DUCATI Panigale 1299, DUCATI Panigale 959, DUCATI Panigale 1299
Is it imit?
I was able to do it without problems for installation.
No problem with texture.
Seat bag US-10https : / / www. webike. net / sd / 20013033 /
I went to a day trip to Mount with.
It is nice to have it installed, but we will gap to the driver side in about 30 minutes.
Gap about 10 cm from the initial position.
I hit the driver's buttocks so I am very anxious.
It is not until it falls...
The reason is that the mounting pitch is shorter than the Pitch of Bag and the Motorcycle side is short.
I think that this installation method will not be established in Panigale.
I regret that I like the texture of Bag, but I replaced it with another Bag.
View detail
Fits: KAWASAKI W400, KAWASAKI W400, KAWASAKI W400, KAWASAKI W400, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650
Daytona saddleback
The Daytona saddleback is an indispensable product for travelers. This model is made for kawasaki w800. Put on the model. Beautiful. The material is strong and durable. Used for attaching to bags as well. And most importantly, ordering products via Webike has a system that meets international standards. Home delivery on schedule and have good shipping packaging no damage thus having confidence in both product and service standards from Webike (translated by Google Translator) Daytona saddleback products are indispensable for travelers. This model is built for the kawasaki w800 straight model. The material is durable. Suitable for attaching to the bag as well. And the order of the Webike has a system with international standards. Arrive home on schedule. And have good transport packaging. No damage. This ensures that both Webike products and service standards are guaranteed. View detail
Although the cut of a rear cowl is required to attach to a phasor, Every one right and left, 2 cm x about (it goes out simply with nippers) 4 cm, Since it appears in the instruction manual and the perforated line is contained also in the cowl side
Although the cut of a rear cowl is required to attach to a phasor,
Every one right and left, 2 cm x about (it goes out simply with nippers) 4 cm,
Since it appears in the instruction manual and the perforated line is contained also in the cowl side from the beginning perfectly, the place to cut for true -, [ easy ]
That there are two stars (although looked in, to the extent that it does not understand) which are not known by any means if it does not look in from the bottom even if cutting [ which wages had as I have you attach in a store / which is not ] temporarily goes wrong,
Although the drilling accuracy of the attached parts made from aluminum having been open at the place bad shifted for a while and these parts become a form inserted in the frame by the side of a car body, it is the point which only a few had to correct with the stick file greatly (it is aluminum, it deletes immediately and can correct).
View detail