Reviews
![EDR α Series GPS Driving Recorder For Motorcycles [Drrorecorder].](https://img.webike-cdn.net/catalogue/images/91097/gwqa_TS.jpg)
Fits: Others
I don't have a Monitor, but Compact is fine.
I bought it in a store, but I will Impression it.
[How is it used?
This model is large enough to fit under the Tandem seat.
How was your experience with it?
I don't have to worry about theft because I can store it under the Tandem seat because there is no Monitor, but I have to connect my phone to Wi-Fi to watch the recorded video with my phone, but the time until I can watch the video is too long. The best way to watch it quickly is to remove the SDCard from the body and play it on the PC. You can play back the video on your PC, but it's a pain to remove the SDCard.
The picture quality is clean, the LED signals are recorded with the lights on properly, and the Motorcycle is so quiet that shaking is not a problem at all. I have no problems at night or in the Tunnel.
[Points to note]
If you have a Radar detector, you may also suffer from spatial extraneous radio waves from this product.
[ITEMS TO BUY TOGETHER
Camera Bracket for EDR MITSUBA:Mistuba Sankova Item No.:EDR-P05
Camera Bracket for EDR MITSUBA:Mistuba Sankova Item No.:EDR-P04
Dr-Recorder Camera Bracket PLOT:PLOT Item Number:DRS012
Drraco Camera Bracket PLOT:PLOT Item Number:DRS002
Dr-Recorder Camera Bracket PLOT:PLOT Item Number:DRS001
[Opinions and requests to Manufacturer
The unwanted radiation is within the specified value, but it is a problem in practical use.
Keep an eye out for coexistence with Radar receivers.
View detail
It is recommended to mount the Camera on the License Plate Bolt after mounting the Camera.
I bought this for the installation of the RearCamera of Mistuba Sankova EDR-21Gα.
I think it's better to install the camera after you install the camera.
The Nut that comes with the installation is M3 and small, so I didn't have the right tool on hand and lost the Nut and went to the home center to buy one.
Be careful
I bought the one for the upper Left, but I think the one for the upper Right might have been better for the angle of view.
View detail
That's the strength of OEMOption!
It may seem a bit expensive, but as it is a ManufacturerOEMOption, it is Exactly right for a CameraMount Bracket. View detail
Sits great!
Mistuba Sankowa EDR-21Gα for Camera mounting.
If you have trouble finding a place to install the RearCamera, use this one.
All your problems are solved at once!
View detail
![EDR α Series GPS Driving Recorder For Motorcycles [Drrorecorder].](https://global.webike-cdn.net/photo/impression/2b/2b40466dd2fb1bd05c338355bd71df78L.jpg)
Fits: Others
It's a must to install the front rear2ch drarecorder.
I ride a moped Grom, and whenever I go on a touring trip of around 100K round trip, I always get overtaken twice by unreasonable drivers.
When you are driving with a gap between you and the car in front of you, some cars suddenly move out into the opposite lane of the Right Side and try to pass you.
It's also a lateral Limit.
I've already decided that I need to add a DVR to protect myself, so I installed this product.
FrontCamera is not enough for me, so I looked for a 2CH product and found this product.
I was waiting for the EDR-22G which was supposed to be released this summer, but the other day the Manufacturer's website said that the supply of electronic components was not available and that it would be released around April 2022, so I gave up and went with the EDR-21Gα.
Well, the functionalities are almost the same, so let's call it good.
As for the installation, since I have KITACO's Power Outlet Port Harness, the Power Supply Cable on the Dr-Recorder side needs to be processed by Male's Bullet Terminal.
The Body is installed on the Battery, I cut it off because it interferes with the plastic which receives the documents on the Seat side.
Wiring is unexpectedly long, so I keep it between Tank and Shroud.
Especially the front side, the fine adjustment of the Camera position is super hard. It is recommended to work by two people if possible.
The handheld Switch is placed under the Handlebar and the GPS Antennas are placed on the Front forkStubby.
The work took two hours with one person working.
The recorded image is also very clean and the License Plate can be clearly identified.
I'm sure it will be a great help to me as a soloMain.
View detail
The installation of the FrontCamera drrorecorder is very easy.
We have installed this product, which is compatible with the installation of Mistuba Sankoowa's EDR-21Gα drrorecorder.
I was planning to install Stubby on Front fork and put Camera on it, but Stubby is too expensive!
You made a Small leap of faith when you discovered this product. Even this one!
It comes with a mounting screw, but since it is very small, it is necessary to install the Camera in a quantity before installing it in the vehicle.:It is better to Set.
Attach the Bracket to the vehicle and then attach the Camera to the Quantity:If you set it, you will lose Screw.
I wanted to install it as Compact as possible, so I gave it 100 points.
I'm very happy with the way the Camera is mounted.
View detail
Items that make the installation of the Drarecorder Camera easier.
We have installed this product, which is a good match for the installation of Mistuba Sankoowa's EDR-22Gα drrorecorder.
I was initially considering one for the upper Right as it is from the Right Side that I get passed by cars from behind.
However, if you look at your motorcycle from the back, you will see that there is an exhaust system on the Right Side.
I bought the one for the top of the Left because I thought that maybe the exhaust air pressure might scare the Camera or make it dirty.
Since it is a moped, the width of the Number is Small, and the length of the Bracket is the same as 170mm, the Quantity:Pair (for Left and Right) You can adjust it, but if you shift it from the Center to either side, you can see the Bracket.
Bracket length could have been about 20mm shorter.
Also, it comes with a screw for installation, but it is too small to install the Camera with the Bracket on the vehicle.
Once the Bracket is removed from the vehicle, the Camera can be installed.
It has a good amount of wall thickness and is quite solid.
I'm very happy with the way the Camera is mounted.
View detail
If you're going to put your phone on, this is the way to go.
I chose Short to keep it low, but the height is just right. The height is just right. The normal length is too tall and doesn't look good, so this is the right choice.
It's a shame it looks so rugged and crudely finished.
Knob is also spurred by Large threshold.
View detail
![[Optional Accessories for DDR-S100 Drive Recorder] Wind Noise Reduction Filter [Drive Recorder]](https://global.webike-cdn.net/photo/impression/2a/2a5b2866b4d59c3fe36fa1c5321e2fa1L.jpg)
Improvement of Wind Cutting sound
What made you decide to buy?
DAYTONA:MiVue M760DDriveRecorder - To reduce the Wind Cutting sound
How was your experience with it?
MiVue M760DDriveRecorder-Control switch has a built-in Microphone. The sound of the wind like the noise that this Microphone catches the running wind ... There is room for improvement! I felt, and as a result of searching variously, from DAYTONA as well Wind Cutting Sound Reduction Filter The MiVue M760DDriveRecorder is not compatible with DDR-S100, but it was sold for DDR-S100. In order to improve the driving wind, the selling price was also cheaply purchased, because it is not a MiVue M760DDriveRecorder exclusive product, the fit is not good..., but I was able to paste it to the Microphone part. It is the Wind Cutting sound of the problem, but the structure of the motorcycle, it does not disappear perfectly. As the name of the product, it is reduction Filter. I think I was able to soften the sound more than before I installed it. By the way, the Filter and FilterDouble-sided Tape come in a pack of two, so you can keep the other one.
View detail
Paste the Switch of Small Type to the Ministry Space.
I bought this to attach the Switch from my Dr-Recorder to my Handlebar.
I was worried because it's not Screw stop, but the Switch itself is light enough that it's not a problem.
It is easy to install and reassuring for space-saving installation.
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3
EDR-21 installed on DAYTONA's Fender Eliminator Kit!
I installed the EDR-21 on the DAYTONA Fender Eliminator Kit. I was worried about the rear side, but I was able to fix it well, and I was able to check the video without feeling any vibration. View detail
RAM MOUNT Security Knob for 1.5-inch Ball Arm
Because it is equipped with a RAM mobile navigation bracket, I am usually too lazy to disassemble it for fear of trouble, but it is convenient if others want to take it away. If it is lost, it will be hundreds of dollars, so it is equipped with this special anti-theft lock. The material is also good, the price is not expensive, and the screw is very tight, even if the speed is more than 150, it will not loosen, it is very tight and stable. You can also hang it on the keychain if you don’t use it. If you buy a RAM phone holder, it is recommended to equip it with an anti-theft lock. ---------------------------------------------- Because with a RAM cell phone navigation stent, usually basically do not bother to trouble removal, but if someone wanted to take the words are easy to lose, then that is a few hundred pieces did not, on the allocation of the special anti-theft locks. Look at material material is also good, prices are not expensive, and tighten very tight, even if the speed of more than 150 will not loose, very tight very stable. When not in use, then you can hang the keychain above, if you buy a cell phone holder RAM recommended anti-theft lock with a very convenient. Powered by Google Translator View detail
Fits: DUCATI SCRAMBLER(800), HONDA CB1000R, HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB125R, HONDA CB1300F, HONDA CB150R, HONDA CB250R, HONDA CB400SB, HONDA CB400SS, HONDA CB750, HONDA CRF1000L Africa Twin, HONDA CRF250L, HONDA CRF250RALLY, HONDA CTX700, HONDA DN-01, HONDA GB250, HONDA GROM, HONDA GROM
Sub-optimally mounted.
I already installed one of them by processing CrownNut as shown below.
URL → https://imp.webike.net/article/477619/
I attached this to the Separate HandlebarsFixing Screw M8 part of the FZr for fun (mystery).
Processing is as shown in the image.
It will fit in the Upper Cowl Bracket without interfering.
I'm going to use an old digital camera here as a drum recorder.
The video seems to have taken a running scene.
View detail
It is used to fix Holder of Smartphone.
As shown in the picture, I buy it to attach Camera directly, not Smartphone Holder.
Because it is a hobby to take a movie when touring, when there is this, Camera is attached to the body side, and it becomes the substitute for DriveRecorder.
The video shows the touring scenery.
View detail
It is made of Gold and is solid.
The image shows the length comparison with standard Size.
The thing of standard Size is used for Smartphone, but when ActionCamera is installed, it makes it Long, and it uses it for the animation shooting from the Screen.
Because it is a considerably long article, be careful about the interference with Screen.
The video is Touring scenery.
View detail
It's like I'm scratching an itch.
I have been using 3 units of W800, ELIMINATOR 250V and FORZA (https://imp.webike.net/rider/Bk3zFyuo3yCvMlvNGruU/mybikeList.html) with RAM MOUNT's smartphone STAND for a long time. I have been using RAM MOUNT's smartphone STAND on my W800, ELIMINATOR 250V, and FORZA () for a long time, but I could not turn them to the direction I wanted to point them well due to the problem of the range of motion, so I decided to purchase this product.
this "RAM MOUNT SwivelArm is a very itchy product.
RAM MOUNT's normal arm (https://www.webike.net/sd/21313050/) and short arm (https://www.webike.net/sd/21313052/) have a limit of bendable angle between the cloak part and the joint part of the phone. In my case, there was a case that I could not point it at the angle I wanted to point it.
In this respect, the SwivelArm here allows you to change the direction in the middle of the Arm, so you don't feel the inconvenience you used to feel at all.
View detail
Strong enough Base.
I installed it on 2020 YZF-R1.
warp and woof
I did not want to affect the handling of this motorcycle, which is said to be the Yamaha of Handlebars, when installing the Ram Mount, and wanted to install it in a place other than the Top Bridge or Stem Mount, so I bought it to co-tighten with the Tank fixed Bolt.
good point
Because it is a ManufacturerOEM, the most important strength and connectivity was not a problem at all.
I'm happy to say that I can't find any bad points this time.
Installation
The diameter of the bolt I bought is M8, but the diameter of the Tank fixed bolt is M6, so I put a collar in this mount to adjust the gap, and because the length is not enough, I bought a new Stainless bolt and tightened it after applying Aluminum Grease.
You may not need such information especially, but this Bolt Base is sold only M8 or M10, so you tend to give up when Size is different, but if you do it well, you can install it anywhere you want, so I hope you can install it with ingenuity without giving up.
I'm not sure what to make of it.
View detail
Same ease of use as standard Arm
I was using a standard arm, but with the change in mounting position I wanted to use a short arm
In my case, when I'm not touring or in places where I'm worried about theft, I leave the Arm attached to the XGrip and remove it.
However, since there is no spring in the short arm, when the Knob is loosened, both sides of the ball support become empty, and the Neck is not so easy to use.
So, at my own risk, I put the Spring for the standard Arm through the Bolt of the Short arm, and put the GripBand for the Bud MINTON on the side I didn't want to remove, and it became the same usability as the standard Arm!
It seems to be durable because it doesn't come off because of the cone shape, and it doesn't cut or crack though it has passed nine months since I installed this Band!
I feel like I'm doing an impression of the GripBand! (Lol)
View detail
high rigidity
I used it to install a Chinese Dr-Recorder and GPS Antennas along with Camera.
It's very rigid, so the Camera image didn't get blurry.
View detail
Fits: DUCATI SCRAMBLER(800), HONDA CB1000R, HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB125R, HONDA CB1300F, HONDA CB150R, HONDA CB250R, HONDA CB400SB, HONDA CB400SS, HONDA CB750, HONDA CRF1000L Africa Twin, HONDA CRF250L, HONDA CRF250RALLY, HONDA CTX700, HONDA DN-01, HONDA GB250, HONDA GROM, HONDA GROM
The Greatest Thing Behind the Edge of Unbreakable Support
It is a little different from the current one because the one I own is an old MODEL. At the time of purchase the Bolt that came with the Ballius at the time of purchase prepared Stainless bolt on its own because the length is insufficient.
BALIUS? (Domestic 4-cylinder 250cc NAKED) It has been used for 8 years and over 100,000 km at
From this point of view, it's proven to be the best when it comes to durability.
It is a base for installing the kit, which can be fixed firmly and securely without breaking it and also supports the upper kit firmly. If it's fixed properly, neither the kit nor the phone will ever fall out, no matter what you do, whether you run through the forest road or the bumpy Winding like the Iroha Slope with full throttle of Axel, or the maximum speed challenge, you won't have to worry about the Gap.
According to our friends at Forest Road Rider, the Motorcycle didn't seem to break after one turn sideways on the slope.
Material:There is no discoloration or cracking of the surface and no sticking to the surface, which are common in plastic products.
The product is the best, so now it's just a matter of which Arm you choose...
View detail