Reviews
Very good.
Motard bikes do not have space to store the body, and I was concerned about the large size of the body. I chose this model because the body is small and the connecting cable is SMART and thin.
I was very anxious about the purchase, but I was able to install it without any problems, and I am glad that I was able to use the included double-sided tape and tie wrap instead of using a bracket.
View detail
Pretty good
I don't know about other drarecorders, but it is a normal shot.
Command on Switch is easy to understand and the UserInterface of the application is very clear.
I feel that the parking monitor is less likely to be triggered by the weak battery in SR400. However, the engine is started within 5 KICKs.
View detail
The installation was Large strange, but I am satisfied.
Because of ADV160, it takes time to detach Cowl and handle Wiring.
It took almost a day, but the images are beautiful.
The Bluetooth connection was also not bad.
If possible, we hope that it will not have to be used to verify the accident.
View detail
TimePlus is fun!
Image quality (default 58 fps) is fair
The daytime image quality Number can barely recognize all letters before and after the stop, and 4-digit numbers at the back of the second unit of Right.
When you start driving, you can recognize 4-digit numbers even in the front and back.
One point, I would like to add that there are three picture quality settings:58fps, HDR, and HDR.
1080p/58fps、1080p/29fps、HDR1080p/29fps
Motorcycle is not good for drareco
Yamaha・XG250 TRICKER
I can't compare the picture quality because it's my first driver's camera, but I felt the picture quality wasn't as good as I thought it would be.
There may be a single-cylinder effect and a problem with the location of the installation.
The app is a little unstable, but useful.
The high quality MODE of 1min1File58fps is 100MB, and the DOWNLOAD feels quicker at about 7 seconds.
I think it is easy to use (although I don't know about other apps) because it also shows map and speed during video playback and the own car Pin works.
However, when I tried to play and DL other files, the Wi-Fi connection was broken, etc. It seemed a little unstable.
The SDCard is screwed into the Plus, so it is good to be able to watch videos without the need to remove the SD card.
・TimePlus
The 1 hour and 15 minute run was combined into one video of approximately 5 minutes and 350 MB.
The video is one File per minute (default value) and the GPS on the map is only that section, but
With TimePlus, the entire driving route is displayed, making it easy to look back and enjoy looking back.
View detail
Convenient to have!
I could not find a good place to mount it, so I bought a Mirror mount because it was EXACTLY what I wanted. As a result, it was Exactly!
I was able to install it without any problems, but I am only worried about theft.
The screws are dedicated to prevent theft, but if the Bracket is broken or the Mirror is removed, it is the end of the world.
I would rather be able to take it off and on easily, so I can carry it with me.
So, I am Covering as a self defense.
View detail
Camera abnormality immediately after opening the package.
After opening the package, I connected the battery and checked the operation, but the Camera error message kept blinking and I could not record. View detail
as always
The Plate is not so bad, but the SMARTness after installation is good. View detail
New car installation
Control switch of JupiterNavigation, which is frequently used, is installed on the Left Side.
DAYTONA DAYTONA:DriveRecorder-Control switch with MirrorM10Clamp installed on the Right Side.
View detail
OGK I put it on EXCEED.
B+COM Sorry.
OGK for summer Dislike BoomMicrophone for EXCEEDHelmet's Income and B+COM B-COM:WireMicrophoneHolder is now available and used for SENA20S
The Double-sided Tape on the Mounting Adapter seemed weak.
View detail
For RearCamera, a driverless camera
I was looking for one for my RearCamera for my DoraRecco and found it.
I am very satisfied with the large size of the product, which is securely fastened to the Fixing Screw of the License Plate without any fear of falling off.
View detail
Dora Reco for Front
I was looking for a place to mount the FrontCamera for the DRA recorder and was looking for some related parts and I found this.
I think the price is a little high, but I am satisfied.
View detail
It's worth a try
When we replayed the first video from the DVR, we could not hear anything but the terrible Wind Cutting sound.
I was looking for an Option product at that time and happened to find it and bought it.
When we tried it, the Wind Cutting sound was considerably suppressed and the Engine sound could be heard on the Level, and we were fairly satisfied.
Try it and see.
(Can't we at least include this in the package?)
View detail
Wind Cutting sound of the Dora Recorder was so bad that I put it on.
The Wind Cutting sound of the M760D was so bad that I put this product on to try it out.
It is not for the M760D, but it came on without any problem.
Even a child can do it because it is only attached with double-sided tape. (Lol)
Before I put it on, it was beeping even when I ran at about 40km/h.
The video is running at about 60km/h, but there is no Wind Cutting noise to be concerned about.
The effect is quite good and recommended.
View detail
Also available as for Front.
Used for NMAX for Front.
It can also be used for FrontCamera by replacing the rings and Bolt & Nut.
The "for Rear" is not usable as it is because the outer diameter of the Camera is different.
The Bolt for this product is Torque.
View detail
I bought the Repair item because I only needed the front.
When it comes to cost performance, Quantity:Set purchase would be best, but
I bought the forward CameraSingle Item because the rear Camera and other parts are wasted.
The images are only information about the installation of the system in such a place.
I went to DIYCenter and bought a 1.5mm thick AngleBracket of a board for about 100-200 yen. Buy an AngleBracket about 1.5mm thick.
Drill a 6mm hole in the Motorcycle Bracket to tighten it together, and paint it black.
It seems that double-sided tape is the basic method of attaching a bracket for a camera, but I was a little worried about it.
Tie Wrap was also fixed.
View detail
As a countermeasure for Wind Cutting sound
I bought and use it for DDR-S100.
I drive about 5,000km a year for touring and it lasts me about a year.
Others, it wears in the BodyMicrophone of AS300 of SONY, Wind Cutting reduction is built in this machine, but I put it with the measure of the dust and the insect, the sound enters beautifully.
View detail
If you want to mount it on the Handlebar, it might be possible.
When replacing the DDR-S100 with the Mivue M770D, the DDR-S100 has a MountQuantity option.:I was using Set and wanted to do a similar installation here so I bought it.
Mount of DDR-S100 is Material:I liked the texture in Aluminum, but this is Material:I'm a little disappointed with the look of the plastic. It will probably get whiter with use.
The Nut which is the pair with a special Bolt is probably 6mm though I did not measure it, and I pinched Nut with Long nose pliers and tightened it because there was no Spanner etc. which can correspond in the Tools Set at the time of installation.
I mean, Spanner might be able to fix it, but even if there is a Socket, I think the root of Mirror is in the way and I can't fit the tool to Nut.
Because Clamp itself wraps the Cap of Camera's Rear, it is troublesome that the Cap cannot be removed unless Clamp is loosened every time and the angle is also gap every time Clamp is loosened.
Well, I think that the construction of this clamp and the special bolt together deter theft.
View detail
Looks good after installation.
I bought this together with my MiVue M777D drrorecorder.
Because Rear is set to Fender Eliminator and License Plate Holder is installed, the quantity of License Plate:Pair (for Left and Right) The reason why I bought this product was that it seemed to be incompatible with the Bracket which is tightened together with the Bolt, and I thought that the appearance after Camera installation would be refreshing.
The wrench for the special Bolt is included, but I didn't have a Spanner or Socket in my tool box that fit the Nut on the receiving end, so I used Long nose pliers to pinch the Nut and tighten the Bolt.
I haven't measured it, but I think Nut is probably 6mm.
I thought it is not good to tighten Bolt nut too much because Clamp part is made of resin.
However, Clamp has a softness to fit Camera, so if this is destroyed, I think that the special Bolt is meaningless.
I took a spin around the neighborhood after installation, and the vibration from driving didn't change the mounting angle.
I'll take another look at it next time I go Touring.
View detail
You only have two choices.
There are two types of brackets available from DAYTONA, but the MONKEY125 can only use this bracket.
If it's a Honda, there is a possibility that the OEM uses the same parts, so you need to check.
The only way to attach a heptagonal switch is to buy a Bracket. The Handlebar is wrapped with a Hemp palm, so you can use it to attach a flat Switch to a round Pipe.
The saltiness that I installed is good for the location because I can reach my fingers without any problem to control the Switch.
However, the operation will be stopped and it will be done with the smart phone, and it cannot be confirmed that it operates without Monitor by two Button operation, and it cannot learn the operation. (T_T)
The thing is made of iron, which I hope will not rust, and it is strong enough not to run away even if you press the Switch.
There was no BALI and the finish was beautiful.
In order to install it by tightening the friend to Mirror, I tightened it by turning it for the angle which escapes when it moves assuming the position to tighten it because it turns when tightening it. However, because it does not have to face the front like Camera, I thought that it was rather Easy and good (the point is only good if it can operate)
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
If possible, it is better to have two people work on it because the direction of the mirror and the direction of the bracket need to be aligned and the handlebar turns when tightened. It's better to have two people working on it.
However, the person who installs this is probably an expert who has also installed DriveRecorder, so he will probably do it without worrying about it. ( *´weed)
View detail
The product is good, and because of its odd shape, the mounting direction can be chosen.
This is a special product for DAYTONA's MiVue M760D Camera, and if it cannot be mounted on the vehicle body, this is the only option.
It will be installed by friend tightening on Mirror.
If you don't set the angle so that it faces straight, you need to be careful because Camera will face the other place because it is tied with in Hemp palm.
However, if you tighten it, it will be scratched, so if you don't tighten it in one shot and tighten or loosen it again and again, it will damage the paint and call rust.
I had it tilted to assume the angle that the Bracket would rotate while tightening, and when I tightened it, it faced the front. You need to have a hunch.
As for the direction of installation, it is better to think about turning it to the back or the front while considering the circumference of CameraWiring. When the place where it is cut diagonally is put together with the brake master, it becomes beautiful, but the phenomenon that the gold good cable comes near unusually and is covered with the switch occurred.
The thickness of the plate is strong enough to prevent shaking due to the plate, but there is nothing you can do to prevent the Handlebar from picking up shaking, so you should move it to the body.
after all "Something like this. If possible, I would like it to be made of stainless steel by laser cutting.
View detail