Reviews
For the use of Income.
I have been using a btx2 pro s with a SZ-RAM4 and bought it with Speaker so that I could use it with my new SHOEI Z-8. I was so attached to the SZ-RAM4 that I couldn't bear to retire it, and since I would likely want to use Jet in the hotter months, I decided to keep it too. I decided to keep it, and the question arose as to what to do with Income.
When using Income, the Microphone is available in Included Parts:for full face, and it is sufficient to use the unused one in Included Parts:for the mounting Clamp, but the Speaker and SlideMount need to be replaced or newly prepared each time they are used. However, the Speaker and SlideMount need to be replaced or newly prepared each time they are used.
I thought about changing the Speaker and SlideMount for each season, but I decided to purchase the Speaker and SlideMount because it is troublesome to take off the interior and put on and off each time, and if I just attach the Body, I can use different Helmets depending on my mood. I decided to purchase a Speaker and a SlideMount.
For installation, we decided to use double-sided tape to attach the outside of the clamp, which was not used in the Included Parts:section, to the helmet, but the SlideMount, which we purchased additionally, does not come with two screws to fasten it to the clamp, We had to think of a way to fix it to the Clamp. At first, I was thinking of using one screw for each SZ-RAM4 and Z-8, but I didn't want to damage the screws by applying excessive force, so I decided to prepare screws. However, this was not the Size sold around the corner. I had to buy a clamp to attach the screws, and it cost about 2,000 yen for two small screws. I had no choice but to use the regular screws for the Z-8, and for the SZ-RAM4, which is likely to be used less frequently, I removed the Clamp once, removed the Screw holder from the Clamp, and fixed the SlideMount to the Clamp with 2.5mm diameter Screws and Nut to make it ready to be used. The Clamp was removed and the Screw holder was removed from the Clamp.
As for the wiring, in the SZ-RAM4, the wires were placed inside the helmet, crossing the edge of the helmet, so it was necessary to protect the wiring from damage when the helmet was placed on the ground, etc. In the Z-8, the wiring could be pulled inside the helmet without passing through the point where it hits the ground, etc., so no protection was needed. However, with the Z-8, it was possible to pull the wiring inward without passing through the point where it hits the ground, so no protection was needed, and the wiring was well concealed, making it look very refreshing.
After installation, it works fine and I can now use Income on my Z-8. For this gold price, I would like to see at least a Screw included in the kit.
View detail
It was saved.
I purchased a new Helmet.
I think it is LiNori that I don't have to buy the whole IncomeBody, but I felt it was a bit pricey.
View detail
It was saved.
I purchased a new Helmet.
It was quite helpful not to have to buy the entire IncomeBody.
View detail
To replace the Helmet on DT-E1.
Purchased Wiring and Speaker to mount on two different Helmets.
Only the Body can be replaced, which is more convenient.
View detail
To the self-satisfied immeChain.
Not in terms of performance, but for FashionStyle's self-satisfaction!
It's a regular plastic frame, so you might expect it to be a little cheaper, but it's moodUp??'sItems.
The exchange procedure is not that difficult.
It can be easily removed by inserting a flat object such as a slotted screwdriver and connecting it, but I think that a plastic spatula can be used for recommendation without damaging the body, rather than a gold driver.
View detail
Just give me what I want at Rose~!
"I bought this because the Tape on the Microphone was peeling off.
Nothing wrong with the quality.
One thing that bothers me is the price, since everything is all-in-one, including the anti-slip of the Body and the fixed Seal of the Speaker.
It is a Kit with poor performance for a Situation like mine, where I only want the Microphone part.
I know it's not SDGs, but I don't think it's a sustainable Parts supply that can be used for a long time, and I would like to see it available at RoseRose. "
View detail
Purchased for different use of Helmet.
I bought the Helmet without Speaker because of the different use of the Helmet and the lack of a recess for Speaker on the Helmet.
The shape of the helmet causes the base to float, so it is not attached and used as a clip stop.
The price of the Base and Speaker is quite expensive, so I think it is expensive considering the cost performance. Also, DAYTONA's Income has a variety of repair kits, so I think this is a good point.
View detail
It purchased in order to hear the congestion information of a highway radio, etc. I think that the die length and texture of a cable are also good.
It purchased in order to hear the congestion information of a highway radio, etc.
I think that the die length and texture of a cable are also good.
View detail
I wish the Manufacturer would figure out what Velcro is for!
Income DT-E1's Helmet side Surface Fastener and Base plate side Surface Fastener, but IncomeBody also comes with this product.
However, the Base plate of Include Parts:of the same Income (17123) This Surface Fastener on the back side of (Hard side) and paste in the (Product Spec.) However, once the two are attached, if you try to remove the base plate to separate them, the Helmet's Surface Fastener (Soft side) The Surface Fastener part other than the Double-sided Tape of the tape is torn off, and it becomes impossible to use it again.
This is why I purchased this product.
I hope that Manufacturer will think properly about this.
View detail
I think it's a bit pricey.
I bought it for Makeover.
Installation is very easy as you just need to fit it in.
I just think it's a bit pricey.
View detail
It's a bit pricey though.
The material is the same as that of regular Sponge, so the price seems high. I'm glad I bought the Income brand, which has a very strong brand, but Repair Parts is available and I can order only what I need. View detail
I think it's good that you can buy it as a Single Item.
I replaced the Microphone only because the person I was talking to couldn't hear me because of all the noise. After the exchange, I can use it without any problem, but the breakdown of the microphone seems to be early. However, because I can buy it cheaply with Single Item at Repair Parts, I think it is good. View detail
Procure spare parts out of print
Two to three months have passed since I purchased DAYTONACool RoboGT Body, but discontinued products came out with some consumables. It is out of print so soon ... ( / Ω ) and started procuring spare parts. This is Helmet holder to fix Body. I'd like to wait a little more and make it to GT 2.
View detail
Since the tandem was carried out in many cases, it used a long time ago. A battery uses one 9V dry cell. a battery -- having -- it seems that it is fairly good. On the Hokkaido touring for one week, the changing battery was carried out only on
Since the tandem was carried out in many cases, it used a long time ago.
A battery uses one 9V dry cell.
a battery -- having -- it seems that it is fairly good.
On the Hokkaido touring for one week, the changing battery was carried out only once.
Although volume control is possible, since it in practice used, having fixed with the volume maximum, there may be no meaning to which the volume is attached not much.
With the structure of the whole back very appropriate for handmade, a power switch did not have a mark of ONOFF, either, and since LED etc. were not attached, it was puzzled at first.
And it is the greatest fault that only two situation plugs can be inputted.
Since radio and music needed to be listened to carrying out a tandem in the case of, it has changed there at the same time tandem & mixing amplifier DF1011 was put on the market.
Although a price becomes high about 5000 yen, since all the above-mentioned demands are satisfied, the recommend of that one can be carried out individually.
View detail